混合交通下右转机动车信号配时方法

为了减少右转机动车与直行自行车之间的干扰,提高交叉口的运行效率,本文分析了两相位信号控制交叉口右转机动车与自行车之间的冲突规律以及自行车交通流的行驶特性,确定设置右转机动车信号的直行自行车流量临界值.以减少冲突和提高交叉口运行效率为目标,确定右转机动车相位绿灯起亮时刻和绿灯时长,并建立了相应的参数标定模型.以实际调查数据为基础,应用VISSIM模拟软件进行模拟验证,结果表明,设置右转机动车信号后,右转机动车延误和机非冲突明显减少.     

Molten salts/ceramic-foam matrix composites by melt infiltration method as energy storage material

A new type of high temperature energy storage material was obtained through the melt infiltration method, using compounding SiC ceramic foam as matrix and Na₂SO₄ as phase change material. The resulting composite material was measured by XRD, SEM, TG-DSC methods. The experimental results indicate that the composite is composed of silicon carbide, sodium sulfate and square quartz, and no chemical reactions occurs between Na₂SO₄ and SiC matrix. Na₂SO₄ has a good bonding with the SiC ceramic foam matrix. As the composite material is characterized by high thermal energy storage density and high thermal conductivity, it is suit for energy storage under high temperature. Funded by the “863” Hi-Tech Research and Development Program of China (2008AA05Z418)     

树脂增强选择性激光烧结多孔金属件的研究

针对选择性激光烧结(SLS)间接方法成型的金属零件形坯,经脱脂和高温烧结后形成的零件存在大量孔隙和空洞,其致密度和强度都较低,不能满足实际应用要求的问题,采用改性耐高温环氧树脂浸渗零件烧结坯的方法,使多孔金属件致密化,并粘结内部金属网架,提高零件的机械性能.对浸渗烧结坯的拉伸强度的测试和扫描电镜(SEM)以及热失重(TGA)的分析结果表明,浸渗树脂后的烧结坯拉伸强度提高了约4倍;改性环氧树脂和金属网架粘结在一起,形成一个密实的网络结构,致密度大幅提高;零件可在200℃的温度下使用.该方法可以制造注塑模具和功能零件.     

An improvement to the simulation of phase-change heat-transfer during soil freezing and thawing

A new variable time step method, which is called the backwards calculating time step method, is presented in this paper. It allows numerical simulation of soil freezing and thawing while avoiding "phase change missing and overflowing". A sensitive heat capacity model is introduced through which the calculation errors are analyzed. Then the equation using the self-adjusted time step is presented and solved using finite differences. Through this equation, the time needed for a space cell to reach the phase change point temperature is calculated. Using this time allows the time step to be adjusted so that errors caused by "phase change missing and overflowing" are successfully eliminated. Above all, the obvious features of this method are an accelerated rate for adjusting the time step and simplifing the computations. An actual example proves that this method can accurately calculate the temperature fields during soil freezing and thawing. It is an improvement over traditional methods and can be widely used on com- plicated multi-dimensional phase change problems.     

强化两相混合的超临界技术制备聚乳酸微粒

针对商品化聚乳酸微球粒径分布较宽难于适用气溶胶给药要求的不足,采用水力空化混合强化超临界流体辅助雾化技术(SAA-HCM)制备聚乳酸(PLA)超细微粒.该技术主要特点是通过在超临界流体和液相进料处引入水力空化混合器,强化两相间的混合.考察SAA-HCM过程混合器压力、温度、沉淀器温度、进料中CO2与液体溶液质量流量比和溶液质量浓度等操作参数对微粒形态和粒径分布的影响,成功制备出球形度较好,粒径分布较窄(1～3μm)的PLA微球.经X射线衍射(XRD)分析和差示扫描量热(DSC)分析显示,与原料PLA相比,微球晶型及热曲线变化不大,但结晶度下降.同时把操作参数与相行为进行关联,探讨了影响颗粒形貌的机理.对比超临界流体辅助雾化法(SAA)的实验结果表明:水力空化的引入能有效强化混合器内的两相传质,混合更好,能制备出适用于气溶胶给药要求的超细微粒.     

电子剪切散斑技术在木材无损检测中的应用

复合板材及木制品等表面或内部的缺陷对材料性能有很大影响,如何快速准确地对其进行无损检测,并判断缺陷的位置大小是很有意义的.针对松木板试件,通过预置表面和内部隐藏缺陷来近似模拟实际缺陷情况,提出一种基于剪切散斑干涉技术的木材无损检测技术新方法,实现了对松木试件的无损检测.在表面缺陷的检测中讨论了剪切量对结果的影响,利用像素标定的方法,得到直径为6、5、3mm的缺陷信息;在内部隐藏缺陷检测中,借助热加载技术同时引入相移技术使剪切散斑检测技术不仅具有非接触、全场实时检测等特点,而且完成对内部隐藏近表面缺陷的定量无损检测.整个检测过程光路简单,实时快速,实验结果与实际情况符合较好.     

Oxidation and Fracture Strength of High-Purity Reaction-Bonded Silicon Nitride

Reaction-bonded Si₃N₄ (RBSN) made from high-purity Si powder is unusually resistant to degradation caused by exposures to air for up to 50 h at temperatures up to 1400°C. The weight gain during oxidation of this SiH₄-originating RBSN is approximately 10 times less than conventional RBSN. Contrary to normally observed strength degradations, room-temperature strengths of this high-purity, oxidized RBSN (avg = 435 MPa, max. = 668 MPa) remained at their unusually high, as-processed levels after 1000° and 1400°C oxidizing exposures. Fracture toughness values were unaffected by oxidation ( K _IC= 2.3 to 2.4 MPa · m^1/2). This superior oxidation resistance results from the high purity and the small diameter pore channels (0.01 to 0.06 μm) achieved in this SiH₄-originating RBSN.     

Pressureless low temperature sintering of nanocrystalline zirconia ceramics via dry powder processing

Pressureless sintering approaches provide a simple avenue to manufacture dense ceramic parts with minimal processing equipment, but current pressureless sintering techniques have yet to demonstrate capabilities of producing dense ceramics while maintaining sub-50 nm grain sizes. Nanocrystalline yttria stablized zirconia ceramics were process from 4 mol% yttria stablized zirconia (4YSZ) nanopowders with a crystallite size of 7.5 nm using dry cold isostatic pressing (CIP) where powders are dried immediately prior to green compact formation and CIP vacuum bagging. It is shown that CIP pressures >75 000 psi (517 MPa) effectively remove pores larger than 100 nm and that pressureless sintering occurs at reduced temperatures for green densities ≥50%. Though the sintering kinetics are shown to be similar to other zirconia nanopowder sintering studies, the small initial crystallize size and reduced sintering temperature allowed densities as high as 97.2%, while retaining a ceramic grain size at or below 40 nm. Produced nanocrystalline 4YSZ ceramics with a grain size of 30.3 nm and a density of 96.3% had Vicker's hardnesses as high as 14.2 GPa and Vicker's indentation fracture resistance of 3.43 MPa·, demonstrating that simple processing approaches can be refined to fabricate nanocrystalline ceramics while maintaining high hardness and indentation fracture resistance.     

Effects of coagulation bath temperature on structure and performance of poly （vinyl butyral） hollow fiber membranes via thermally induced phase separation

Poly （vinyl butyral） （PVB） hollow fiber membranes were fabricated via thermally induced phase separation （TIPS）. The effects of coagulation bath temperature （CBT） on the structure and performance of membranes were investigated in detail. The morphologies of the membranes were studied by scanning electron microscopy （SEM）, the performances of water permeability, rejection, breaking strength and elongation were measured, respectively. The results indicate that all the membranes have the asymmetric morphology and the thickness of the skin layer decreases and the pore size of the outer layer increases with the increase of CBT. The permeability of membranes prepared at air gap 1.0 cm and take-up speed 0.253 m/s increases from 1.047×10-7 to 5.909×10-7 m3/（m2·s-kPa） with the CBT increasing from 20 ℃ to 40℃, and sharply increases to 35.226×10 7 m3/（m2.s.kPa）once the CBT arrives at 50 ℃. While the carbonic ink rejections have no significant decrease, totally exceed 98%, but that of acid-maleic acid copolymer greatly decreases with the increase of CBT. Both the breaking strength and elongation decrease with the increase of CBT.     

磁场中双量子位Heisenberg模型的纠缠与量子相变

以双量子位Heisenberg模型为例,讨论了磁场方向对纠缠的影响。结果表明：一定温度下,保持磁场的大小不变,仅改变其方向,不仅能获得最大纠缠,还产生了量子相变。