磷复肥喷浆造粒“三内”技术研究与开发(一)

介绍磷复肥喷浆造粒“三内”技术 ,该技术集喷浆造粒、分级、返料、破碎为一体在转筒内完成全过程 ,实现机头喷浆机尾出产品 ,粉体在筒内闭式循环造粒新技术     

Surface crosslinking of high‐density polyethylene beads in a modified plasma reactor

High‐density polyethylene (HDPE) beads were successfully surface‐crosslinked in a modified plasma reactor. The modified plasma reactor treats large amounts of beads, which are uniformly surface‐crosslinked. In this study, effects of the gas pressure, radio‐frequency (RF) power, and the treatment time on the degree of surface crosslinking were systematically investigated. Degree of surface crosslinking was measured by solvent extraction method (boiling xylene method, BXM). The gel content of plasma‐treated HDPE increases from 0.0 to 1.05% within 10 min at 100 mTorr, 200 W. FTIR and DSC analyses show that the crosslinked layer after plasma treatment is limited only at HDPE surface without changing the bulk thermal property of HDPE. Through the analysis of FTIR, it was confirmed that main peaks corresponding to CH₂ bands were decreased and two peaks corresponding to CF₂ and CF₃ were observed after plasma surface modification. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 2921–2929, 2002; DOI 10.1002/app.10295     

Low-temperature catalytic growth of carbon nanotubes under microwave plasma assistance

Various carbon nanotubes (CNTs) including aligned arrays, Y-branching and some other novel morphologies have been catalytically grown on anodic porous alumina template (APAT) and on the alumina-supported catalysts with methane (or benzene) as carbon source under microwave plasma assistance below 520 °C. The growth process could be simply operated since neither heating nor bias-voltage was applied to the catalysts or APAT. The results presented in this paper not only greatly richened the nanostructures of carbon family but also provided with a new technique path for synthesizing CNTs or some other nanostructures with the characteristics of low-temperature which has some special advantages or applications.     

等离子体技术在化学合成中的应用

从等离子体的基本特性出发,综述了等离子体技术在氨气合成、有机物合成、高分子合成以及纳米碳管的合成等方面的应用和最新进展,并展望了等离子体技术在化学合成方面的应用前景.     

人血浆蛋白C的纯化与鉴定

目的　建立人血浆蛋白C的纯化与鉴定方法。方法　利用DEAE SephadexA 5 0代替氯化钡 ,对血浆进行预处理 ,再经DEAE SepharoseFF离子交换和肝素 SepharoseCL 6B亲和层析进行分离纯化 ,用活化的部分凝血活酶时间 (APTT)测定组分活性 ,非还原型SDS PAGE测定其相对分子质量 ,Westernblot鉴定其特异性。结果获得相对分子质量为 6 2 0 0 0的蛋白条带 ,此条带可与人蛋白C单克隆抗体发生特异性反应。结论　已成功地从血浆中分离到蛋白C ,为其规模化生产奠定了基础。     

甲烷浓度对金刚石薄膜(100)织构生长的影响

以H2和CH4的混合气体为气源,用微波等离子体辅助化学气相沉积法(MPECVD)在1 cm×1 cm S i(100)基体上沉积了金刚石薄膜。研究了不同的甲烷浓度对金刚石薄膜(100)织构生长趋势的影响。分别采用扫描电子显微镜(SEM),Ram an光谱对金刚石膜的表面形貌、质量进行了分析。结果表明,当基体温度为750℃,气压为4.8×103Pa,甲烷浓度为1.4%时,薄膜表面为(100)织构。     

生物陶瓷人工骨制备的新方法

主要介绍了近年来发展起来的两种新技术 :快速原型制造技术和放电等离子烧结技术。概括了两种技术的原理、特点以及在人工骨制备中的应用 ,提出了用这两种技术制备人工骨的设想。     

The role of pressure on thin amorphous carbon films deposited using microwave surface wave plasma CVD

We report the effects of gas composition pressure (GCP) on the optical, structural and electrical properties of thin amorphous carbon (a-C) films grown on p-type silicon and quartz substrates by microwave surface wave plasma chemical vapor deposition (MW SWP CVD). The films, deposited at various GCPs ranging from 50 to 110 Pa, were studied by UV/VIS/NIR spectroscopy, atomic force microscopy, Raman spectroscopy, X-ray photoelectron spectroscopy and current–voltage characteristics. The optical band gap of the a-C film was tailored to a relatively high range, 2.3–2.6 eV by manipulating GCPs from 50 to 110 Pa. Also, spin density strongly depended on the band gap of the a-C films. Raman spectra showed qualitative structured changes due to sp³/sp² carbon bonding network. The surfaces of the films are found to be very smooth and uniform (RMS roughness < 0.5 nm). The photovoltaic measurements under light illumination (AM 1.5, 100 mW/cm²) show that short-circuit current density, open-circuit voltage, fill factor and photo-conversion efficiency of the film deposited at 50 Pa were 6.4 μA/cm², 126 mV, 0.164 and 1.4 × 10^− 4% respectively.     

Surface and Interfacial Studies of Plasma-Modified Composite Surfaces

Model epoxy and bismaleimide compounds in thin film form were used to simulate epoxy and bismaleimide composite surfaces, in order to study compositional changes and interfacial reactions induced by oxygen plasma treatment. X-ray photoelectron spectroscopy (XPS) and infrared reflection-absorption spectroscopy (IR-RAS) were used to probe chemical changes which occurred. XPS and IR-RAS were found to be complementary techniques in determining the nature of functional groups incorporated into surfaces by plasma treatment. IR-RAS analysis of the model surfaces following exposure to a liquid epoxy resin revealed that while adsorption of the liquid epoxy occurred on both plasma-treated and nonplasma-treated surfaces, the oxygen plasma-treated surface alone was capable of initiating ring-opening reactions in the epoxy. However, this effect was not observed unless immediate contact was made between the plasma-treated surface and the liquid epoxy resin, illustrating the short-lived reactivity of the functional groups on the plasma-treated surface.     

Evaluation of some of the properties of plasma treated wool fabric

Low temperature plasma (LTP) treatment was applied to wool fabric with the use of a nonpolymerizing gas, namely oxygen. Properties of the LTP‐treated samples including low stress mechanical behavior, air permeability, and thermal characteristics were evaluated in this study. Kawabata evaluation system fabric (KES‐F) was employed to determine the tensile, shearing, bending, and compression strength properties and surface roughness of the specimens. The changes in these properties are believed to be closely related to the interfiber and interyarn frictional force induced by the LTP. The decrease in the air permeability of the LTP‐treated wool fabric was found to be probably because of the plasma action effect on increasing the fabric thickness and a change in fabric surface morphology, which was confirmed by scanning electron microscopy micrographs. The change in the thermal properties of the LTP‐treated wool fabric was in good agreement with the earlier findings and can be attributed to the amount of air trapped between the yarns and fibers. This study suggested that the LTP treatment can influence the final properties of the wool fabric, and also provide information for developing LTP‐treated wool fabric for industrial use. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 5958–5964, 2006