铝质基体上Ti(C,N)/TiN多元多层膜工艺参数研究

首先在大范围内调节负偏压和基体温度两个参数，实现在铝质材料基体上沉积与基体结合良好的TiN膜，在此基础上通过调节N2、C2H2工作气氛流量比及Ti(C，N)、TiN膜层的层数，沉积了3类不同的膜，并对其力学与摩擦学性能进行了考察。结果表明：在(N2 C2H2)总流量一定的情况下，C2H2流量增大，则使Ti(C，N)膜层中含C量增多，膜层硬度提高，但韧性变差，表面变粗糙；在总厚基本不变的情况下，层数增多，单层变薄，使膜材晶粒细化，硬度提高，韧性变好。在3类膜中，1#膜C2H2流量适当且膜层数最多(6层)，其摩擦学性能表现最好，临界荷载为76N，显徼硬度为1911HV0.1，与基体相比，耐磨性提高了10倍多。     

Electroless coating of Permalloy powder and DC-resistivity of alloy composites

A high-resistivity coating of Permalloy (Ni–17.81Fe–1.97Mo wt.%) powders for soft magnetic composites, SMC, was developed and characterized. The coating was made using the electroless plating method employing an aqueous solution of sodium and nickel phosphates. The chemical process led to the formation of a layer up to 1 μm thick deposited on each particle surface and composed of a mixture of Ni(OH)₂, P₂O₅ and NaPO₃ compounds, as shown by X-ray photoelectron spectrometry and X-ray powder diffraction studies. The effect of coating on electrical DC resistivity was evaluated on SMC obtained mixing the metal, coated or uncoated, and thermoplastic polymer PEEK (polyetheretherketone) powders, pressing the mixture at 800 MPa and heating in air up to melting the polymer (380–410 °C). The SMC made with coated powders showed an increase in resistivity of more than two orders of magnitude compared to that obtained with uncoated powders when the polymer ranged between 0.5 and 1.5 wt.%. This difference prevails in comparison with sintered materials processed at the same pressure and sintering in hydrogen at 1350 °C. Thus, this process would restrict the eddy currents which affect the performance of soft magnetic products for AC applications.     

Synthesis and characterization of nanocrystalline ZrNxOy thin films on Si by ion plating

Based on the optimum deposition conditions of ZrN thin film from our previous study, by varying oxygen flow rate ranging from 0 to 8 sccm, nanocrystalline ZrN_xO_y thin films were deposited on p-type (100) Si substrates using hollow cathode discharge ion-plating (HCD-IP) system. The objective of this study was to investigate the effect of oxygen content on the composition, structure and properties of the ZrN_xO_y thin films. The oxygen content of the thin film, determined using X-ray photoelectron spectroscopy (XPS), increased with increasing oxygen flow rate. As the oxygen content increased, the color of the ZrN_xO_y thin film changed from golden yellow to blue and then slate blue, and the microstructure observed by scanning electron microscopy (SEM) varied from columnar structure to finer grains and finally flat and featureless structure. Phase separation of ZrN_xO_y to ZrN and monoclinic ZrO₂ was found from X-ray diffraction (XRD) patterns when the oxygen content was higher than 9.7 at.%. The hardness of the film slightly increased as the oxygen content was less than 9.7% and then decreased to 15.7 GPa, a typical hardness of ZrO₂ phase, as the oxygen content further increased. The total residual stress of the film was measured using an optical method, and the residual stresses of ZrN and ZrO₂ phases were determined separately using modified XRD sin²ψ method. The total stress was close to the stress in ZrN phase as the ZrO₂ fraction was less than 30%, and was close to that in ZrO₂ phase as the ZrO₂ fraction was over 30%. The electrical resistivity of the film increased significantly with the increase of oxygen content. The film properties showed consistent trend with phase separation. As the fraction of ZrO₂ phase was small, the apparent properties of the films were more close to those in ZrN. When ZrO₂ fraction was over 30%, the films mainly exhibited the properties of ZrO₂.     

电刷镀Ni-P-Al2O3-碳纳米管复合镀层工艺研究

采用电刷镀的方法，在金属零件表面沉积一层Ni-P-Al2O3-碳纳米管复合材料。实验表明，通过对碳纳米管进行氧化、敏化和活化等预处理，可使碳纳米管颗粒均匀地分散在刷镀层中；施镀溶液温度应控制在55℃，pH值在1．5-2．5。碳纳米管的加入可有效地防止刷镀层裂纹、易剥落、结合强度低的缺陷。     

超硬磨料表面镀覆(涂覆)的种类、方法及用途(Ⅰ)

本文概述了超硬磨料镀覆(涂覆)的发展过程及常用方法，分析了各种方法的优缺点，并针对目前在超硬磨料镀覆(涂覆)及相关制品方面存在的对镀覆种类使用不当的问题进行了辨析。本文由于篇幅问题分为两部分，在(Ⅰ)中主要介绍了超硬磨料表面电镀和化学镀镀覆Ni、Cu及部分利用物理方法镀覆Ti等金属的方法、性能及用途；在(Ⅱ)中介绍了超硬磨料表面镀覆(涂覆)Ti等强碳化物形成元素及刚玉等方法、性能及用途。、     

石墨颗粒表面化学镀铜研究

为了充分利用Cu的导电性能，碳石墨的润滑性能，改善Cu/C的润湿性，用化学镀铜的方法成功地对石墨颗粒表面进行镀覆，详细地研究了镀铜液组分及工艺与石墨颗粒表面镀铜层厚度、沉积速率的关系，并得出较好的组分工艺方案，采用优化工艺可以得到平均厚度约7．1μm的镀铜层。同时应用X射线、金相显微镜、扫描电镜及电子探针对镀铜层的厚度、表面形貌、镀铜层与基体的界面进行了全面观察。分析表明，Cu/C界面存在过渡层，界面成锯齿状，机械冶金结合的特征十分明显，改善了铜碳界面的相溶性。     

用稀土钇提高离子镀TiN膜层与基体结合力的研究

研究了不同含量稀土钇对离子镀ＴｉＮ膜与基体结合力的影响，结果表明，加入稀土钇后，大大提高ＴｉＮ膜与基体的结合力，并使膜层内ＴｉＮ相增加，此外，稀土钇能明显提高镀膜过程中钛料蒸发率，在相同镀膜内，能使ＴｉＮ膜层加厚。     

Ni-P-金刚石粉化学复合镀层的性能

本文用扫描电镜对Ni－P－金刚石粉化学复合镀层的表面状态及内部形貌进行了观察，并用图像处理仪定量计算了复合镀层中金刚石粉的体积百分数。结果表明，随镀液中金刚石粉添加量增加，镀层中金刚石粉含量也增加；金刚石粉在镀层中呈均匀分布。同时，测定了复合镀层的力学性能，结果指出，复合镀层中金刚石粉含量增加，硬度、耐磨性提高。     

过渡金属硫化物纳米材料化学复合镀层制备方法

介绍了无机类富勒烯(Inorganic fullerene-like,简称IF)与过渡金属硫化物(WS2和MoS2)纳米材料的常用合成技术--固-气与气相反应合成方法; 以及用化学复合镀法制备含有IF-WS2纳米颗粒的Ni-P复合镀层的方法.     

短碳纤维表面化学镀铜工艺研究

实验用NaOH对短碳纤维亲水化处理，无需敏化、活化等工艺直接放入镀液中化学镀铜，研究了镀液温度、pH值和装载量对镀层质量的影响。用光学显微镜观察了镀层的表面质量。结果表明，当温度为60℃，pH值为13，装载量为0．1g／60ml时．获得的镀层光滑致密。