高温合金IN690管材挤压损伤模拟

采用有限元软件对高温合金IN690管材挤压损伤进行预测,研究挤压速度对损伤的影响规律,得到不同的挤压条件下的挤压阈值。不同挤压速度下损伤的变化随着挤压速度变化呈现先增大后减小的趋势。模拟摩擦系数为0.01、0.05、0.1、0.2条件下的损伤,在摩擦系数为0.01时,坯料表面比较光滑,损伤比较轻;摩擦系数为0.2时,表面凹凸不平,损伤严重。     

球磨参数及Ni比例对Mg2Ni合金储氢性能影响研究

采用中频感应炉熔炼出铸态Mg2 Ni合金,将Mg2Ni合金与一定量的Ni粉进行混合球磨处理.系统研究在不同Ni粉添加量及球磨时间等条件下所得合金样品的结构及储氢性能.研究表明,随着Ni含量的增大及球磨时间的延长,合金的非晶纳米晶结构逐渐增多;合金的最大放电容量及循环稳定性得到明显提升;合金的表面催化活性及合金体相内的H传输能力都有了显著提高.Ni粉的作用主要在于可促进合金非晶化,同时对合金的放氢过程起到了催化的作用.     

氧化铈对Fe55自熔合金喷焊层组织与性能的影响

通过水雾化方法制备了Fe55自熔合金粉末,并通过在粉末中加入不同稀土量用氧乙炔火焰喷焊的方法在45钢板基材表面制备合金涂层,研究了稀土氧化铈对Fe55自熔合金喷焊层的组织和性能的影响.     

Effect of rare earth samarium addition on the kinetics of precipitation in AI-Cu-Mn casting alloy

The mechanical properties of Al-Cu-Mn casting alloy mainly depend on the morphology, distribution, size, and number ofθ′（Al2Cu） precipitates. In this study, we have analyzed the effect of rare earth samarium （Sm） addition on the kinetics of precipitation in the Al-Cu-Mn casting alloy by using differential scanning calorimetry （DSC） and high-resolution transmission electron microscopy. Thermal ef-fect peaks that are attributed to the formation and the dissolution of Guinier-Preston （GP） zone andθ′phase were identified from the DSC curves. The activation energy ofθ′formation was calculated by using both the Kissinger method and the analytical model, and the corre-sponding results were compared. Results suggest that the activation energy ofθ′formation in Al-Cu-Mn alloy is dramatically higher than that in Al-Cu-Mn-Sm alloy. Accordingly, it is concluded that the addition of rare earth Sm decreases the activation energy ofθ′formation and promotes the formation ofθ′precipitates.     

Anodic behavior and microstructure of Al/Pb-Ag-Co anode during zinc electrowinning简

In order to study the anodic behavior and microstmctures of A1/Pb-Ag-Co anode during zinc electrowinning, by means of potentiodynamic investigations, scanning electron microscopy （SEM） and X-ray diffraction （XRD） analyses, the mechanism of the anodic processes playing on the surface of A1/Pb-0.8%Ag and A1/Pb-0.75%Ag-0.03%Co anodes prepared by electro-deposition from methyl sulfonic acid bath for zinc electrowinning from model sulphate electrolytes have been measured. On the basis of the cyclic voltammograms obtained, information about the corrosion rate of the composite in PbO2 region has been concluded. The microstructures were also observed by means of SEM and XRD which showed Pb-0.75%Ag-0.03%Co alloy composite coating has uniform and chaotic orientation tetragonal symmetry crystallites of PbSO4, but Pb-0.8%Ag alloy composite coating has well-organized orientation crystallites of PbSO4 concentrated in the certain zones after 24 h of anodic polarization. It is important that Al/Pb-0.75%Ag-0.03%Co anode oxide film consists of non-conductive dense MnO2 and PbSO4 and a, fl-PbO2 penetrated into which, in fact, are the active centers of the oxygen evolution after 24 h of anodic polarization.     

TM-Gd合金系非晶形成能力的热力学研究（I）

在Co-Gd二元系合金体系的热力学优化评估的基础之上,应用CALPHAD （ CALculation of PHAse Diagram）技术,研究此二元非晶合金的玻璃形成能力。本文分析了700 K、800 K时Co-Gd合金中各元素含量对非晶形成能力的影响,预测了非晶形成的最优成分,计算过冷液相中的结晶相形成驱动力。通过与部分实验和非晶共晶点准则的比较可见,本文所做的热力学分析对此二元合金的非晶制备具有一定的理论指导意义。     

Mechanical,electrical, and thermal expansion properties of carbon nanotube-based silver and silver-palladium alloy composites

The mechanical, electrical, and thermal expansion properties of carbon nanotube（CNT）-based silver and silver–palladium（10：1, w/w） alloy nanocomposites are reported. To tailor the properties of silver, CNTs were incorporated into a silver matrix by a modified molecular level-mixing process. CNTs interact weakly with silver because of their non-reactive nature and lack of mutual solubility. Therefore, palladium was utilized as an alloying element to improve interfacial adhesion. Comparative microstructural characterizations and property evaluations of the nanocomposites were performed. The structural characterizations revealed that decorated type-CNTs were dispersed, embedded, and anchored into the silver matrix. The experimental results indicated that the modification of the silver and silver–palladium nanocomposite with CNT resulted in increases in the hardness and Young＇s modulus along with concomitant decreases in the electrical conductivity and the coefficient of thermal expansion（CTE）. The hardness and Young＇s modulus of the nanocomposites were increased by 30%？40% whereas the CTE was decreased to 50%-60% of the CTE of silver. The significantly improved CTE and the mechanical properties of the CNT-reinforced silver and silver–palladium nanocomposites are correlated with the intriguing properties of CNTs and with good interfacial adhesion between the CNTs and silver as a result of the fabrication process and the contact action of palladium as an alloying element.     

An investigation on electrochemical performances of as-cast and annealed La0.8Mg0.2Ni3.3Co0.2Six（x = 0-0.2） alloy electrodes for Ni/MH battery application

The La-Mg-Ni-based A2B7-type La0.5Mg0.2Ni3.3Co0.2Six （x=0-0.2） electrode alloys were prepared by casting and annealing. The influences of the additional silicon and the annealing treatment on the structure and electrochemical performances of the alloys were investigated systemically. Both of the analyses of XRD and SEM reveal that the as-cast and annealed alloys are of a multiphase structure, involving two main phases （La, Mg）2Ni7 and LaNi5 as well as one minor phase LaNi3. The addition of Si and annealing treatment bring on an evident change in the phase abundances and cell parameters of （La, Mg）2Ni7 and LaNi5 phase for the alloy without altering its phase structure. The phase abundances decrease from 74.3% （x=0） to 57.8% （x=0.2） for the （La, Mg）2Ni7 phase, and those of LaNi5 phase increase from 20.2% （x~0） to 37.3% （x=0.2）. As for the electrochemical measurements, adding Si and performing annealing treatment have engendered obvious impacts. The cycle stability of the alloys is improved dramatically, being enhanced from 80.3% to 93.7% for the as-annealed （950 ℃） alloys with Si content increasing from 0 to 0.2. However, the discharge capacity is reduced by adding Si, from 399.4 to 345.3 mA.h/g as the Si content increases from 0 to 0.2. Furthermore, such addition makes the electrochemical kinetic properties of the alloy electrodes first increase and then decrease. Also, it is found that the overall electrochemical properties of the alloys first augment and then fall with the annealing temperature rising.     

Microstructure and mechanical properties of AZ31 alloy ingot fabricated by semi-continuous casting

The AZ31 alloy ingot with diameter of 110 mm and length of 3500 mm was fabricated successfully. The compositions and microstructure morphologies of the ingot at different locations were performed, which indicated that the chemical composition distributed homogeneously through the whole alloy ingot and the average grain size increased from the surface to the center. The results of the EDS and element face-scanning illustrated that the eutectic compounds mainly consisted of fl-Mg17Al12 and a small amount of fl-Mgl7（AlZn）12. Furthermore, slight improvements of the strength and ductility were observed from the center to the surface along the axial direction of the alloy ingot, while both the strength and elongation to failure of the samples along the radial direction are higher than that along the axial direction. The fine grain strengthening was the main contributors to the strength of the as-casted AZ31 alloy.     

Effects of Al and Sn on electrochemical properties of Mg-6%Al-1%Sn （mass fraction） magnesium alloy as anode in 3.5%NaCl solution

Mg-6%Al-1%Sn（mass fraction） alloy is a newly developed anode material for seawater activated batteries. The electrochemical properties of Mg-1%Sn, Mg-6%Al and Mg-6%Al-1%Sn alloys are measured by galvanostatic and potentiodynamic tests. Scanning electron microscopy（SEM） with energy dispersive spectrometry（EDS） is used to characterize the microstructures of the experimental alloys. The results show that the Mg-6%Al-1%Sn alloy obtains more negative discharge potential（-1.38 V（vs SCE）） in hot-rolled condition. This is attributed to the fine dynamically recrystallized grains during the hot rolling process. After the experimental alloys are annealed at 473 K for 1 h, the discharge potentials of Mg-6%Al-1%Sn alloy are more negative than those of Mg-6%Al alloy under different current densities. After annealing at 673 K, the discharge potentials of Mg-6%Al-1%Sn alloy become more positive than those of Mg-6%Al alloy. Such phenomenon is due to the coarse grains and the second phase Mg2 Sn. The discharge potentials of Mg-1%Sn shift positively obviously in the discharge process compared with Mg-6%Al-1%Sn alloy. This is due to the corrosion products pasting on the discharge surface, which leads to anode polarization.