热致液晶性纤维素衍生物及其热塑性塑料复合物熔体流变行为的研究

用毛细管流变仪研究了乙基纤维素（ＥＣ）及其高密度聚乙烯（ＨＤＰＥ）复合物，纤维素芳族酯（ＣＡＥ）及其聚碳酸酯（ＰＣ）复合物的剪切流变特性和机理。结果表明，ＥＣ对ＨＤＰＥ／ＥＣ复合物的粘度影响不大，而少量（５％）ＣＡＥ的加入使ＰＣ／ＣＡＥ复合物粘度大大下降，且复合物流变曲线呈现新的特征。     

Three‐dimensionally braided carbon fiber–epoxy composites,a new type of material for osteosynthesis devices. I. Mechanical properties and moisture absorption behavior

In recent years, three‐dimensionally (3D) braided composites have attracted a great deal of attention because of their high‐impact damage tolerance and fatigue life, superior fracture toughness, and so forth, and have been used in aeronautics, military, and transportation. These advantages make them strong candidates for osteosynthesis devices. In this study, 3D braided carbon fiber–epoxy (C_3D/EP) composites were produced via a simple vacuum impregnation technique. The load‐deflection curve, mechanical properties, and influence of fiber volume fraction, braiding angle, and axial reinforcing fibers were examined to determine their suitability for internal fixation devices. It is found that the C_3D/EP composites have excellent toughness and do not show brittleness when fractured because of their relatively high void content. The flexural, shear, and impact strengths of the C_3D/EP composites are excellent. It was shown that a C_3D/EP composite with a stiffness similar to load‐bearing bones can be made while maintaining enough strength. It is concluded that a relatively higher void content and braiding angle is more suitable for the C_3D/EP composites from the viewpoint of requirements of fracture fixation materials. The moisture absorption behavior and changes in mechanical properties caused by moisture uptake were evaluated. Results show that absorbed moisture slightly decreases mechanical properties of the C_3D/EP composites. Contrary to the unreinforced epoxy, the moisture absorption behavior of the C_3D/EP composites cannot be described with Fick's law of diffusion, probably because of the presence of voids and/or 3D fiber structure. The exact mechanisms should be proposed in further investigations. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 1031–1039, 2002     

Fatigue behaviour of a phenolic matrix composite

This paper presents results of a fatigue life investigations carried out in plate specimens of a fibre-glass-reinforced phenolic matrix composite. Tensile and Young's modulus data were obtained at four different testing temperatures (room temperature, 100, 150 and 200 °C). The fatigue S−N data were obtained at room temperature only and for two stress ratio values (R=0 and 0.4). Fatigue and tensile behaviour was assesesed in the composite with the fibres aligned in the longitudinal loading direction. The results were obtained for two values of volume fraction (0.28 and 0.42) and three different glass surface treatments. A detailed comparison of fatigue results is given taking into account several fatigue parameters and also the testing variables. Results of observations of SEM fracture surfaces are also presented.     

炭/炭复合材料抗氧化涂层厚度的光学测量

选用A,B,C,D4种炭/炭复合材料试样进行抗氧化涂层厚度的光学测量研究。其中:试样A,B孔隙度相同,均为15.85％,对其涂覆粒径分别为1μm和10μm的B_4C涂层;试样C,D孔隙度分别为13.52％和16.78％,对其均涂覆粒径为10μm的B_4C涂层。然后通过金相光学测量其涂层厚度,在抗氧化涂层厚度的计算过程中,对试样组织的内部未渗入抗氧化涂层的孔隙进行图像处理。结果表明:当试样孔隙度相同时,涂层材料粒径越小,其涂层越厚;当抗氧化涂层材料粒径相同时,试样孔隙度越大,涂层越厚。     

HDPE/CB-GP复合材料体系电性质的研究

当HDPE含量46％（质量分数，以下同）、其它添加剂（如抗氧剂、阻燃剂、交联剂和润滑剂等辅助填料）的含量11％，两种导电填料石墨（GP）和碳黑（CB）的总含量为43％时，研究结果表明石墨含量的变化对HDPE/CB-GP复合材料室温电阻率、阴C强度和后NTC强度有显著的影响．HDPE/CB-GP复合材料中GP的含量〈8．6％时，样品的室温电阻率〈30Ω·m，PTC强度〉7、后NTC强度〈1．3；电阻率．温度曲线经过17次冷热循环后重现性好，复合材料具有实际应用价值；GP在复合材料中为层片状结构。     

核壳型铁钴纳米复合材料的制备及其性能

采用多元醇还原工艺和自组装技术,在微米级Fe粉表面包覆纳米Co粒子,一步法制备了一种具有核壳结构的复合磁性微球,用SEM表征了其相组成和形貌,用VSM测试了磁滞回线,初步研究了磁学性能。结果表明:用该法制备的核壳型Fe/Co纳米复合材料表面包覆致密,其比饱和磁化强度和矫顽力介于微米铁粉和纳米钴粉之间。     

平纹织物复合材料的弹性模量预测

利用细观力学的代表体积元(RVE)法,预测了平纹织物复合材料的弹性模量。建立了表征RVE形态的数学模型,分析了细观结构与宏观性能之间的关系,编制了从组分材料的弹性性能推测复合材料的弹性性能的预测程序。对理论预测进行了实验验证,理论值与实测值在一定误差范围内能较好吻合,说明此预测方法具有一定的可靠性。     

Mechanical properties of poly(ether-ether-ketone) for engineering applications

An outline of the characteristics of PEEK and the versatility of its compositional forms (micro and macro composites) are given to illustrate its wide potential for success in engineering applications. Although it is necessary to have particular tabulations of mechanical properties for engineering design, these are seldom available and consequently it is argued that an understanding of stiffness, toughness and strength properties are required to fully exploit available manufacturer's data and thus develop the full potential of PEEK and its composites. Stiffness characteristics are considered in terms of a modulus function which is dependent on time under load and temperature. In its composite forms, whether reinforced with short or continuous fibres, stiffness anistropy can be both considerable and complex, but some empirical ground-rules are apparent. For continuous fibre composites even in the form of complex lay-ups, it is also possible to attempt some stiffness prediction from certain pseudo-elastic constants. Toughness of PEEK and its composites is described in terms of both comparative and intrinsic properties. Instrumented falling weight impact data, particularly as a function of temperature enable some insight into ductile-brittle transitions for the unreinforced material, but crack initiation and crack propagation processes for the various fibre reinforced forms. Intrinsic toughness is described in terms of linear elastic fracture mechanics theory. Strength properties are described for static and dynamic loading configurations. In particular, PEEK and its composites are evaluated for increasing test severities for strength characteristics; stress concentration, loading form and test temperature are considered.     

纳米Fe/C复合材料的原位合成

在石油渣油中加入二茂铁，通过热缩聚反的位合成纳米级铁粒子均匀分散于炭基体中的新型复合材料，研究了在420℃热缩聚时停时间和二茂铁添加量对Fe/C形成的影响，并用TEM和XRD观测和分析了Fe/C的形态和结构，结果表明，在基体中铁粒子的粒径为25－50nm，在一定条件下，二茂铁添加量的增加和停留时间的延长均使Fe/C产率提高，停留时间对热缩聚反应的影响遵循一级反应动力学，二茂铁的添加能显著提高反应速率常数k值。