Effect of HCl pre-treatment on corrosion resistance of cerium-based conversion coatings on magnesium and magnesium alloys

The corrosion protection afforded by a cerium conversion coating, formed by immersion in a solution containing rare earth salt and hydrogen peroxide, on pure magnesium and two magnesium alloys, AZ91 and AM50, has been studied. The effect of HCl pre-treatments on the morphology and on the corrosion resistance of the cerium conversion layer was investigated. A thicker and more homogeneous distribution of the conversion coating was obtained when the sample surface was pre-treated with acid. Higher amounts of cerium on the surface of the pre-treated samples were detected. The cerium conversion coating increased the corrosion resistance of the alloys because it ennobled the corrosion potential and decreased both the anodic and cathodic current. The acid pre-treatment further increased the corrosion resistance of the coated alloys. After five days of immersion in chloride environment the untreated samples showed localized corrosion while the chemical conversion coated samples appeared unaffected.     

Formation of a chromium-carbide conversion coating on silicon carbide

The formation of a chromium-carbide conversion coating on SiC was achieved using the pack-cementation technique. The conversion coating is intended to improve the corrosion resistance of SiC and its derivatives, such as SiC-base continuous fibers and composites, by forming a protective Cr₂O₃ scale upon exposure to high-temperature corrosive environments. Different pack chemistry and processing parameters were evaluated in the laboratory. Results indicated that the coating morphologies and compositions achieved were significantly affected by variation of these processing factors. In this paper, the conversion coating obtained from one of the systems investigated is reported. The coating consists of a multilayered structure with each of the sublayers containing a high-Cr concentration. In addition, the coating surface is relatively dense and pore free compared to the underlying SiC substrate material. A dense and pore-free morphology is highly desirable for coating applications, especially on porous substrates. The multilayered coating structure consists of the following sublayers: Cr₂₃C₆/Cr₇C₃/Cr₇C₃+Cr₃Si/Cr₅Si₃C_x/SiC substrate.     

101强化粉在水基涂料中的应用研究

叙述101强化粉在涂料中的应用,测定涂料的性能,研究101水基涂料对砂芯的渗透性,防止铁液浸渗的作用.生产结果令人满意.     

铜基体超音速火焰喷涂碳化物涂层界面研究

使用扫描电子显微镜及透射电子显微镜，对铜基体超音速火焰喷涂（HVOF）碳化物涂层的形成过程，组织结构和界面形态进行了研究。结果表明，HVOF涂层界面显微组织非常复杂，存在纳米晶，非晶和大量位错孢，非晶是粘结相在喷涂中受热，骤冷形成的，而涂层中的纳米晶来自半熔碳化物的破碎。     

紫外光固化酚醛树脂的制备及在涂附磨具中的应用

本文通过丙稀酸与环氧酚醛树脂开环反应,制备出能紫外光固化的酚醛树脂结合剂,研究了制备该树脂的合适工艺条件为:催化剂N,N-二甲基苯胺的用量为体系总质量的1%,反应温度为80±5℃,反应时间为5~7h;用这种可紫外光固化的酚醛树脂制作的涂附磨具试样,不仅固化速度快,仅需4~5m in即可固化完全,而且磨削比是常规热固化试样的3倍多,使用性能大大提高。     

聚苯硫醚的性能及在防腐蚀涂层上的应用

较详细地介绍了聚苯硫醚(PPS)的性能、发展概况及在防腐蚀领域的应用前景。根据实践经验叙述了PPS的喷涂工艺，总结分析了影响PPS涂层施工质量的主要因素及解决办法。     

熔渣法碳化铬涂层的抗氧化性能研究

对熔渣法碳化铬涂层在各种温度下经20h和200h的氧化性能进行了研究，与常用的一些锅炉用钢进行了对比试验，结果表明碳化铬涂层抗氧化性能比15CrMo、102、T91钢好，可以与TP347钢相媲美。     

Role of deposition parameters on microstructure and mechanical properties of chromium oxide coatings

Chromium oxide coatings were deposited by reactive magnetron sputtering on high speed steel (HSS) substrate under various oxygen flow rates and radio frequency (RF) powers. The effect of deposition conditions on the microstructure, hardness and critical load of chromium oxide coating failure was studied. The results indicated that a crystalline chromium oxide coating formed at a high oxygen flow rate and a low RF power exhibited a higher hardness and a lower critical load as compared to a chromium oxide coating with an amorphous microstructure.     

Low temperature bonding of LD31 aluminum alloys by electric brush plating Ni and Cu coatings

0Introduction Amongavarietyofbondingtechnologies,vacuum brazinghasbeenwidelyadoptedasareliablemethodfor joiningaluminumcomponents[1],whereintheAl Sialloys systemisrecognizedasthemostpopularfillermetals[2,3]. Althoughasoundjointcanbeachievedforcertainalumi…     

Fabrication of composite wire of lead coated on glass fiber by extrusion

1　INTRODUCTIONCoatingglassfiberwithleadproducesakindofnewcontinuouscomposite ,whichcanfindwideap plicationsinmanydifferentfields ,especiallyinthebatteryoftheEVsandHEVsthathasalreadybecomethemostimportantgoalinmostcountries[13] .Withakindofspecialtechnologythiskindofnewcompos itewirecanbeusedtoproducegridsofnewleadacidbatterythatisveryusefultotheEVsandHEVs .Thiskindofnewleadacidbatteryhasmanyadvan tages ,suchashigherspecificenergy ,lessinnerresis tance ,morequicklychargingcapabilityand…