激光熔覆TiC增强FeAl金属间化合物基复合材料涂层磨损性研究

利用激光熔覆技术在1Cr18Ni9Ti奥氏体不锈钢表面制得了以TiC为增强相、以FeAl 金属间化合物为基体的耐磨复合材料涂层，研究了激光熔覆。FiC／FeAl复合材料涂层在干滑动磨损条件下的耐磨性能及磨损机制。结果表明：随着载荷和滑动速率的增加，TiC／FeAl金属间化合物基复合材料涂层的磨损速率增加，其磨损机制随着载荷的增加逐渐由磨料磨损向粘着磨损转变；激光熔覆层中TiC体积分数的增加，一方面提高了涂层的磨料磨损抗力，另一方面降低了熔覆层表面与对磨材料之间的粘着倾向，提高了TiC／FeAl涂层的滑动磨损性能。激光熔覆TiC/FeAl金属间化合物基复合材料涂层具有优异的耐磨性能并随TiC体积分数的增加而提高。     

氮碳共渗对Ni-W-SiC复合镀层的组织及性能的影响

讨论了Ni-W-SiC复合镀层与氮碳共渗复合强化的组织结构及性能，结果表明，氮碳共渗后复合镀层的硬度和耐磨性远高于未氮碳共渗的复合镀层，扫描电镜结果表明，在共渗处理中，复合镀层存在硬度梯度，且基体中的换向复合镀层扩散，形成“钉扎效应”，显著提高了镀层与基体的结合力。X射线衍射表明，复合镀层经氮碳共渗后，产生很多新相，这些相的存在显著提高了复合镀层的硬度和耐磨性。     

杭州湾跨海大桥钢管桩的涂层防护

杭州湾跨海大桥采用钢管桩沉桩基础。钢管桩的腐蚀问题采用涂层加阴极保护的防护体系,其中涂层部分采用单层/双层/三层重防腐环氧粉末喷涂防护方案解决。介绍了三种涂层结构及其用途。     

超高相对分子质量聚乙烯纤维粘合涂层用水乳型聚丙烯酸酯微乳液的合成

以甲基丙烯酸甲酯(MMA)、丙烯酸丁酯(BA)、丙烯酸(AA)及丙烯酸羟乙酯(HEA)为单体,以十二烷基硫酸钠(SLS)、OP-10和正辛醇的复合物为乳化剂,当m(BA)∶m(MMA)∶m(AA)∶m(HEA)=50∶50∶3∶10、w(乳化剂)=13%、反应温度为80℃及反应时间为3h时,合成了可用于超高相对分子质量聚乙烯纤维粘合涂层的水乳型聚丙烯酸酯微乳液,单体转化率为99 8%,乳胶粒径为30nm,乳液膜的玻璃化温度为-28℃,应用工艺简单,涂层粘附性好、柔软、耐磨。     

风力发电机塔架的涂装

按照设计要求制备用于风力发电机塔架的防腐蚀配套涂料,塔架的筒体内部涂层由环氧树脂聚酰胺富锌底漆和环氧树脂聚酰胺云母氧化铁中涂漆组成,筒体外部涂层由环氧树脂聚酰胺富锌底漆、环氧树脂聚酰胺云母氧化铁中涂漆和丙烯酸脂肪族聚氨酯面漆组成。该涂料体系的防腐涂层可常温固化,厚度达到275μm,防腐蚀寿命可达20年之久,其防腐效果、耐冲击性和耐候性良好。文章同时讨论了涂装工艺过程中易出现的问题及解决办法。     

沥青聚氨酯防水涂料的发展概述

简要介绍了沥青聚氨酯防水涂料的现状、配方设计、性能及应用,并探讨了沥青与聚氨酯的相容性问题。     

水性聚氨酯材料配方设计技巧

介绍了优选法的0.618法和分数法,对其进行改进创新和原理证明,并应用于生产涂料配方设计中。     

换热器表面预处理及防腐工艺

石化换热器许多设备都由碳钢制作,需要涂镀渗防腐,为保证防腐层质量,需要进行严格的表面预处理。概述了机械与化学表面预处理及相关的防腐工艺。     

A novel method for high-resolution imaging of coating distribution within a rough-textured plywood surface

A new method was developed which enabled us to obtain high-resolution images of the distribution of an oil-borne stain in a saw-textured plywood surface. The method involved treating 90 μm thick plywood sections, which had been cut transversely through the wood-coating interface using a sliding microtome, with osmium tetroxide (OsO₄) prior to examination with a field-emission scanning electron microscope (FE-SEM) operating in backscattered electron imaging (BEI) mode. The combination of OsO₄ staining and use of FE-SEM-BEI afforded excellent contrast differentiation between the coating and wood cell walls, revealing coating penetration into even nano-size cell wall cracks and delaminations formed during band-sawing of the plywood. The novel technique described adds a new dimension to probing wood–coating interface.     

Preparation of solar selective absorbing CuO coating for medium temperature application

A new method of preparing CuO solar selective absorbing coating for medium temperature is presented. After pretreatment, brass was overlaid with CuO by chemical plating. The effects of reactant concentration, reaction temperature and reaction time on the absorptivity of CuO coating were investigated. The optimized condition of preparing CuO coating was obtained. The CuO coating was analyzed with X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM). In order to prolong the period of use, the CuO coating was protected by TiO₂. The experiment shows that the TiO₂/CuO coating is more heat-resistant, acid-resistant, and wear resistant than CuO coating, without losing absorptivity markedly. The TiO₂ coating can reduce emissivity and protect the CuO coating. Translated from Journal of Tianjin University, 2006, 39(12): 1485–1489 [译自: 天津大学学报]