地震属性神经网络油气模式识别技术及其在东海的应用

神经网络油气模式识别技术是综合利用地震属性进行油气预测的技术之一 ,它首先通过计算获得多种地震属性 ,综合分析找出对储层油气比较敏感的地震属性组合 ;然后收集油气井与非油气井的井旁道地震属性 ,组成学习样本并进行神经网络学习 ;最后利用学习结果对储层进行油气预测。该技术在东海某工区的应用结果表明 ,振幅统计类和复数道统计类地震属性是对该地区储层油气最敏感的地震属性组合。神经网络油气模式识别技术可以作为东海地区储层油气预测的一种手段。     

碳纳米管/ABS树脂基复合材料的力学性能和雷达波吸收性能的研究

采用竖式炉流动法制备的碳纳米管经液相阳极氧化表面处理后增强ABS热塑性工程塑料。复合材料的力学性能研究显示:碳纳米管的加入有效提高了复合材料的拉伸性能,但材料的耐冲击性能下降。当碳纳米管含量为12 wt%时,复合材料的拉伸强度由45.00 MPa提高到69.96 MPa,杨氏模量由0.75 GPa提高到1.93 GPa。对碳纳米管/ABS复合材料的反射系数测定表明:复合材料在一定频率范围内有雷达波吸收性能。     

不用专门相移装置的三维面形测量

提出一种不需要专用相移装置实现相移，主要利用数字图像处理技术实现三维面形测量的方法，研究结果表明，用原干涉图像及1幅以上的移值条纹图主可能实现物体三维面形的测量。     

Effect of the Liquid-Phase Characteristic on the Microstructures and Dielectric Properties of Donor- (Niobium) and Acceptor- (Magnesium) Doped Barium Titanate

Changes in the microstructure and dielectric properties with the variation of the donor/acceptor ratio in BaTiO₃ ceramics were investigated. In donor-rich specimens, a liquid that appeared during sintering did not penetrate into grain boundaries. However, in the acceptor-rich specimens, the grains were separated by a liquid film during sintering. The much higher mobility of the liquid film than that of the grain boundaries was suggested to cause extensive grain growth in acceptor-rich BaTiO₃. The macroscopic homogenization of dopants because of grain growth in acceptor-rich specimens resulted in changes in the dielectric properties.     

Effect of material and process parameters on the mechanical properties of unidirectional and multidirectional flax/polypropylene composites

Unidirectional (UD) and multidirectional (MD) flax/polypropylene composites were studied. Flax with varying retting degree and boiled flax was used as reinforcement for the UD composites and unmodified and maleic acid anhydride modified polypropylene (MAA-PP) was used as matrix. Multidirectional flax/polypropylene composites were manufactured on laboratory scale and on pilot scale. They were made from needle-punched hybrid flax/PP non-wovens. Normally retted flax as well as boiled flax was used. For the specimens made on pilot scale, a third kind of flax, namely bleached flax was also studied. The influence of different process times and temperatures on the mechanical properties of the composites was analysed. Generally, the composites have adequate good mechanical properties. The unidirectional composites of boiled flax combined with MAA-PP show the best mechanical properties. Contrary to the UD composites, flax treatment did not lead to the expected property improvements for MD composites.     

铜铟铋硫对Sn-Ag基无铅焊料性能的影响

研究了Cu、In、Bi、S元素对Sn-Ag基无铅焊料熔点和铺展性的影响。结果表明:Sn-Ag-Cu三元合金成分为95.5%Sn3.5%Ag1%Cu时具有较低熔点(215℃)和好的铺展性;加入适量的In可降低Sn-Ag合金的熔点和改善铺展性能;随w(Bi)的增加Sn-Ag-Bi三元合金的熔点降低、铺展性变好;Sn-Ag合金的熔点随w(S)的增加而升高,加入少量S能改善Sn-Ag合金的铺展性。     

利用单片机80c196kc实现等间隔采样及采样值的回显

本文主要介绍以单片机80c196kc为CPU对模拟信号进行等间隔采样以及实现对采样值回显的问题。详细介绍了测频软件及电路的实现，对等间隔采样软件实现进行了详细论述：详尽讨论了对于MG-12864-2液晶显示器的电路连接与软件控制方法；对MG-12864-2液晶显示器应用的独特之处做了细致的分析。     

光纤码分多址技术在城域接入网中的应用

分析了光纤码分多址技术O -CDMA在城域接入网中的应用。回顾了O -CDMA技术的发展历史 ,详细地介绍了O -CDMA技术的特点 ,其具有的公平性、灵活性、网络控制管理、对服务区处理能力以及高的安全性使O -CDMA技术成为较好的城域接入网技术。阐述了目前在应用中O -CDMA存在的一些技术方面的问题     

PE/PP共混物卷绕丝微观结构的研究

用透射和扫描电子显微镜研究PP/PE共混物在熔融纺丝时 ,PE掺入对PP结构的影响。研究结果表明 :PE与PP存在一定程度的相互作用 ,PP中加入PE能改变卷绕丝中PP结晶结构 ;PP中加入质量分数低于 10 %的PE时可以顺利纺丝 ,所得的卷绕丝断裂伸长率较大 ,具有良好的可拉伸性     

On connections between 3-d microstructures and their 2-d images

The problem of recovery of three-dimensional microstructural parameters from two-dimensional images is addressed in its inverse form. Three-dimensional inhomogeneous solids with known microstructures are generated virtually and images of their cross-sections are analyzed. Three different types of randomly oriented microcracks and microcracks having preferential orientation with some scatter. Somewhat unexpected result is that, in all the cases considered, three-dimensional defect densities are very close to average values of corresponding two-dimensional parameters.