从数字看发展片式电容器面临的机遇与挑战

采用海关进、出口统计和行业生产统计资料,通过计算、分析,用数字来说明国内发展片式多层陶瓷电容器、片式钽电解电容器、片式铝电解电容器、片式有机薄膜电容器所面临的机遇与挑战,并对其国内市场需求总量、额,国产品在国内市场占有率等做出评估,为有关单位了解片式电容器的发展提供参考,为国产产品更有效地进入国内市场、促进其发展提供依据。     

潮汐河口平面二维非恒定流数值模拟

本文基于三角形网格划分，采用有限元法，建立了平面二维非恒定潮流数学模型。采用了质量集中、压缩存储的处理方法和“预估校正”的时间推进算法，较好地解决了有限元计算存储量和计算速度问题。对长江口南北支河段进行了验证计算，结果表明模型能较好模拟长江口南北支河段的潮流运动情况，且计算稳定性好、速度快、精度高。     

Homogenization of hardness distribution and distortion in high pressure gas quenching

Quenching with gases rather than oil or other liquid media has the advantages of reducing the risks concerning health and environment, while simultaneously homogenizing the quenching results and minimizing distortion due to a wide range of possible process parameter variations and the pure convective heat transfer. In this contribution, a coupled solution for increasing homogenization of quenching results within high pressure gas quenching will be presented. In the first stage, an experimental test facility was set up for flow investigations and in the second stage a numerical simulation model was generated. The numerical and experimental results of the flow through the chamber were compared for several boundary conditions. Finally, after complete verification of the simulation, the model may be used to assist in parameter variation for optimization of homogeneous high pressure gas quenching.     

缝洞型碳酸盐岩油藏流动单元概念和研究方法探讨

流动单元对于提高油田采收率具有很大的实际意义,该项研究在砂岩油藏研究中已取得较大进展。对于缝洞型碳酸盐岩油藏,由于岩石结构构造、成岩后生作用、构造断裂作用、溶蚀作用等多因素对储集空间的影响,已有的流动单元概念及研究技术方法难于应用。以塔河油田为例,针对缝洞型碳酸盐岩地质特征,论证了碳酸盐岩储层渗流屏障的存在及其类型,探索性提出区别于砂岩油藏的缝洞型碳酸盐岩储层流动单元的概念。提出的研究思路和方法包括;油藏压力趋势分析法、井间生产干扰分析法、流体性质差异分析法、井间干扰试井法。结合储层发育特征,初步建立了缝洞型碳酸盐岩流动单元的划分标准。     

Cellular automata model of gravity-driven granular flows

A cellular automata model is used to simulate a variety of granular chute flows. The model is tested against several case studies: flow down a chute, flow past an obstacle, chute flow in which complex, counter-rotating vortices result in streamwise surface stripes and flow near a boundary. The model successfully reproduces experimental observations in all of these cases. These results lead us to propose that simple, rule-based, models such as this can improve our detailed understanding of dynamics and flow within an opaque granular bed.     

EXPERIMENTAL RESEARCH ON EFFECT OF MAIN-FLOW SWING ON FLOW TURBULENCE STRUCTURE

It is mentioned in this paper that the adjustment of flow structure occurs when themain-flow swings.The changes of turbulence structure and flow energy loss in the indoor rivermodel are measured.The experimental data are presented for the first time for the further studyof complicated river flow structure.     

Flow stress of high density polyethylene and nylon 66 at high rates of strain

Measurement of the flow stress of high density polyethylene (HDPE) and nylon 66 at strain rates of 10³ s^?1 using a split Hopkinson pressure bar technique is discussed. The flow stress at a strain of 10% has been determined for both polymers at 20°C. The intrinsic errors involved in this technique are briefly reviewed. The results indicate that the flow stress of HDPE and nylon 66 were 50MPa and 150MPa, respectively, at strain rates of about 10³s^?1.     

Adhesive Dispensing Process Analysis: Steady-State Dispensing of One-Component Adhesives

The process of dispensing one-component heat-cure adhesives was investigated in order to understand current application processes and to guide new process development. Typical one-component adhesives exhibit non-Newtonian rheological behavior, and hence Newtonian fluid mechanics does not adequately describe the dispensing process. In the present study, the adhesives were modeled as Bingham fluids possessing a yield stress and a steady state viscosity. The model of the dispensing apparatus includes four major flow sections connected in a serial configuration. The fluid mechanics equations derived for Bingham fluids in the individual flow sections were solved by numerical methods in order to understand the interrelationships between the material variables (e.g. yield stress, viscosity, temperature dependencies) and process variables (e.g. pressure, flow geometry, temperature, output). The concept of the model is generic and the details of the model can be modified for any forced-flow adhesive application process.

The adhesive flow properties significantly influence the process output. Dispensing temperature, among the process variables, has the strongest effect on process output. A ± 1.0·C perturbation in the dispensing temperature can cause as much as a 14% variation in the bead size for the range of adhesives studied. Differences in flow characteristics result in differences in processability and non-linear temperature/pressure sensitivity. The non-linear sensitivity can be eliminated by operating the dispensing process isothermally. Finally, the process limits for one-component adhesives, which are susceptible to chemical instability induced by viscous heating during processing, are defined and discussed in terms of a modified Brinkman number that takes into account viscous dissipation, heat conduction and convection, and chemical stability of the material during processing.     

PCR芯片和生化微分析系统

介绍了PCR微芯片的最新研究进展,给出了不同结构的PCR芯片设计原理以及特点,介绍由PCR芯片为主要单元的集成微全分析系统的相关研究,同时简要介绍了对PCR的仿真模拟等。     

单片机系统的动态加密技术

单片机系统产品的加密和解密技术永远是一个矛盾的统一体。然而 ,为了更好的保护好自己的单片机技术成果和知识产权 ,加大解密成本 ,研究新型加密技术仍是保护成果的主要手段之一。文中在讨论了传统的单片机系统加密和解密技术的基础上 ,提出一种实用而有效的动态加密技术的实现方案。