工艺参数对PP挤出发泡泡孔结构的影响

研究了螺杆转速、机头口模形状以及机头温度对挤出发泡聚丙烯(PP)泡孔结构的影响。结果表明：在挤出发泡过程中，一定配方、机头形状和温度下，螺杆转速存在最佳值；机头形状越有利于建立高压，制得的泡沫的泡孔越细密均匀且发泡倍率越高；机头口模温度在保证顺利挤出情况下．越低越有利于制得高发泡倍率的泡沫。     

PC/ABS合金研究进展

概述了PC/ABS合金国内外的开发应用现状,并综述了国内外近年来对PC/ABS合金的研究进展,其中包括:PC/ABS合金的相容性技术、相容剂的选用及影响合金性能的因素:原料、组分的配比、成型条件等,并对该合金的发展方向作了简要的分析,认为PC/ABS合金的开发研究在国内塑料合金的工业开发、应用中极其重要,开发的核心是相容化技术。     

Change of short-term memory effect in acute ischemic ventricular myocardium: A computational study

The ionic mechanism of change in short-term memory (STM) during acute myocardial ischemia has not been well understood. In this paper, an advanced guinea pig ventricular model developed by Luo and Rudy was used to investigate STM property of ischemic ventricular myocardium. STM response was calculated by testing the time to reach steady-state action potential duration (APD) after an abrupt shortening of basic cycling length (BCL) in the pacing protocol. Electrical restitution curves (RCs), which can simultaneously visualize multiple aspects of APD restitution and STM, were obtained from dynamic and local S1S2 restitution portrait (RP), which consist of a longer interval stimulus (S1) and a shorter interval stimulus (S2). The angle between dynamic RC and local S1S2 RC reflects the amount of STM. Our results indicated that compared with control (normal) condition, time constant of STM response in the ischemic condition decreased significantly. Meanwhile the angle which reflects STM amount is less in ischemic model than that in control model. By tracking the effect of ischemia on intracellular ion concentration and membrane currents, we declared that changes in membrane currents caused by ischemia exert subtle influences on STM; it is only the decline of intracellular calcium concentration that give rise to the most decrement of STM.     

Event-driven,pattern-based methodology for cost-effective development of standardized personal health devices

Experiences applying standards in personal health devices (PHDs) show an inherent trade-off between interoperability and costs (in terms of processing load and development time). Therefore, reducing hardware and software costs as well as time-to-market is crucial for standards adoption. The ISO/IEEE11073 PHD family of standards (also referred to as X73PHD) provides interoperable communication between PHDs and aggregators. Nevertheless, the responsibility of achieving inexpensive implementations of X73PHD in limited resource microcontrollers falls directly on the developer. Hence, the authors previously presented a methodology based on patterns to implement X73-compliant PHDs into devices with low-voltage low-power constraints. That version was based on multitasking, which required additional features and resources. This paper therefore presents an event-driven evolution of the patterns-based methodology for cost-effective development of standardized PHDs. The results of comparing between the two versions showed that the mean values of decrease in memory consumption and cycles of latency are 11.59% and 45.95%, respectively. In addition, several enhancements in terms of cost-effectiveness and development time can be derived from the new version of the methodology. Therefore, the new approach could help in producing cost-effective X73-compliant PHDs, which in turn could foster the adoption of standards.     

SIMULATION AND ESTIMATION OF LONG MEMORY CONTINUOUS TIME MODELS

Abstract. Some general properties of long memory continuous time processes are recalled or proved. Methods of simulation are studied. A comparison with the usual discrete time autoregressive fractionally integrated moving-average filter is made and illustrations are provided. Then, two methods of estimation of the parameters of such a model from a discrete sample are studied, both theoretically and empirically, with Monte Carlo experiments.     

WALL AND PARTICLE-SHAPE EFFECTS ON HEAT TRANSFER IN PACKED BEDS

The effective radial thermal conductivity and apparent heat transfer coefficient for a packed bed were experimentally determined for beds of spheres, full cylinders and hollow cylinders, for flow rates giving particle Reynolds numbers in the range 100-1000, and for tube to particle diameter ratios of 5-12. Over these ranges the radial Peclet number Pe_r showed significant dependence on solid conductivity, gas flow rate and particle shape, while the wall Biot number Bi showed significant dependence on tube to particle diameter ratio, gas flow rate and particle shape. These dependencies were predicted well by equations incorporating the effects of these variables into individual gas and solid phase parameters, which were then combined to give the effective or lumped parameters     

宽带功率放大器PGSC建模方法及预失真研究

针对宽带功率放大器的强记忆效应特性,提出一种功放建模和数字预失真方法——PGSC模型。利用广义记忆多项式(GMP)、特定交叉项(SCT)及记忆时刻信号交叉项(CIMT)3个基函数来构造功放行为模型及数字预失真器,并搭建实际测试平台对模型的精度及线性化效果进行验证。测试结果表明,与PMEC方法相比,PGSC方法建模时的归一化均方误差减少了2.1 dB,数字预失真时输出信号的三阶邻信道功率比降低了4.94/2.03 dB;与GMP方法相比,PGSC方法仅利用73%的系数即可得到更高的模型精度和更好的线性化效果。     

NiCr薄膜微加热器在低温环境下的电学特性研究

设计了一种适用于深低温环境的微型加热器。使用AC磁控溅射技术将NiCr(80/20 at.%)合金沉积到SiO2/Si基底上,并采用微加工工艺实现薄膜图形化,作为加热器的加热元件。研究了NiCr薄膜的电学性能和晶体结构与退火条件之间的关系。实验表明:在450℃氮气环境下退火30min,可以获得深低温性能优良的NiCr加热器。该加热器在20K时的电阻温度系数(TCR)为80.80×10-6/K。X射线衍射(XRD)分析显示NiCr薄膜在450℃氮气环境下退火后,薄膜的结晶度增大,因此,退火条件对薄膜的电阻率和电阻温度系数有较大的影响。     

基于无线疲劳监测系统的铝合金材料疲劳损伤研究

铝合金材料具有重量轻、强度高等特点,是国民经济发展的重要基础材料,在诸多领域(如飞行器设计与制造、建筑装饰等)中占有十分重要的地位。然而,其抗疲劳性能较差,在交变荷载作用下容易产生疲劳裂纹和发生疲劳破坏。提出了一种基于无线疲劳监测系统的铝合金材料疲劳损伤研究方法,实时监测了铝合金构件的疲劳应变,并实时分析了构件的疲劳损伤状况,为研究铝合金材料的疲劳性能提供了可借鉴性的方法。