PROGRESS IN THE MODELLING OF AIR FLOW PATTERNS IN TIMBER KILNS

Progress in modelling air flow patterns in timber kilns using Computational Fluid Dynamics is reviewed in this work. These simulations are intended to predict the distribution of the flow in the fillet spaces between boards in a hydraulic model of a timber kiln. Here, the flow regime between the boards is transitional between laminar and turbulent flow, with Reynolds numbers of the order of 5000. Running the simulation as a transient calculation has shown few problems with convergence issues, reaching a mass residual of 0.2% of the total inflow after 40-100 iterations per time step for time steps of 0.01 s. Grid sensitivity studies have shown that non-uniform grids are necessary because of the sudden changes in flow cross section, and the flow simulations are insensitive to grid refinement for non-uniform grids with more than 300,000 cells. The best agreement between the experimentally-measured flow distributions between fillet spaces and those predicted by the simulation have been achieved for (effective) bulk viscosities between the laminar viscosity for water and ten times that value. This change in viscosity is not very large (less than an order of magnitude), given that effective turbulent viscosities are typically several orders of magnitude greater than laminar ones. This result is consistent with the transitional flows here.     

Homogenization of hardness distribution and distortion in high pressure gas quenching

Quenching with gases rather than oil or other liquid media has the advantages of reducing the risks concerning health and environment, while simultaneously homogenizing the quenching results and minimizing distortion due to a wide range of possible process parameter variations and the pure convective heat transfer. In this contribution, a coupled solution for increasing homogenization of quenching results within high pressure gas quenching will be presented. In the first stage, an experimental test facility was set up for flow investigations and in the second stage a numerical simulation model was generated. The numerical and experimental results of the flow through the chamber were compared for several boundary conditions. Finally, after complete verification of the simulation, the model may be used to assist in parameter variation for optimization of homogeneous high pressure gas quenching.     

Flow stress of high density polyethylene and nylon 66 at high rates of strain

Measurement of the flow stress of high density polyethylene (HDPE) and nylon 66 at strain rates of 10³ s^?1 using a split Hopkinson pressure bar technique is discussed. The flow stress at a strain of 10% has been determined for both polymers at 20°C. The intrinsic errors involved in this technique are briefly reviewed. The results indicate that the flow stress of HDPE and nylon 66 were 50MPa and 150MPa, respectively, at strain rates of about 10³s^?1.     

Matrix mediated alignment of single wall carbon nanotubes in polymer composite films

Alignment of single wall carbon nanotubes (SWNT) in liquid crystalline (LC) polymer matrix imparting orientation to the nanotubes along the nematic director was studied by atomic force microscopy, measurements of electrical conductivity and Raman spectroscopy of the composite in the directions parallel and perpendicular to the nematic director. The composites were prepared through dispersion of SWNT with LC monomer in a common solvent, their alignment in nematic monomer and consequent UV polymerization of the monomer. The anisotropy of electrical and optical properties of the system depends strongly on the concentration of the nanotubes in the range of 1-10% SWNT being especially strong for smaller concentrations and negligible at higher loads. A simple semi-quantitative model is suggested to account for the orientational behavior of nanotubes in nematic matrices. It successfully describes the observed anisotropy of physical properties at microscale (up to 200 μm) in terms of anchoring of the polymer chains to the nanotubes surface and adjustment of the nanotubes orientation to the nematic direction due to such coupling. The increasing disorientation of the nematic domains at higher nanotubes loads is explained as a development of larger number of LC defects induced by the nanotubes in the nematic matrix due to their intrinsic nature of aggregation. The anisotropy of physical properties at macro scale (several millimeters) is much smaller and less dependable on SWNT concentration because differently oriented LC domains effectively wash out the anisotropy.     

Stability of Periodically Unsteady Axisymmetric Jet

To date, the majority of studies on stability of axisymmetric jets have been completed under the assumption of steady mean flow. Yet, many of the natural and man-made flows that are modeled by these jets can have an inherent unsteadiness; the effects of which on the stability and transition have not been determined. Moreover, controlled unsteadiness can be used to control stability and possibly the transition to turbulence. In this note, the effects of periodic variations of the mean flow on the stability of axisymmetric jets are examined. The problem is treated analytically. The results show that the governing equations and dispersion relation for the unsteady jet can be reduced to those governing the steady jet with a time transformation. It is shown that the periodic variations in the mean flow cause amplitude and phase modulations of the unstable modes. The implications of the modulations on the subsequent transition stages are discussed.     

Heat and Mass Transfer Analogy Studies of Binary Liquid Mixture in Comparison with Eteanol-n-Heptane Evaporating to Air

An expenmental and theoretical study of heat and mass transfer analogy and a comparison of that to a binary liquid mixture evaporation is presented. Common organic solvents, ethanol and n-heptane, were used to form an alcohol - hydrocarbon mixture. Studies were carried out in a horizontal rectangular channel having air flow velocities of 0.2 - 0.9 m/s. Heat transfer coefficients were measured with a copper plate resistor and mass transfer coefficients with a square pool. The heat and mass transfer analogy is presented for a system having two evaporating compounds with a fixed value of air flow and verified by measuring and comparing mass transfer coefficients for distilled water with air flow velocities of 0.2 - 0.9 mls. An illustrative example of the use of the theory for industrial ventilation is presented.     

GaAs FET辐射退化研究

低噪声ＧａＡｓ ＦＥＴ和功率ＧａＡｓ ＦＥＴ经中子辐射都未发生致命性的通或断失效，直流偏置伏态下，其失效模式仅仅表现为源漏饱和电流ＩＤＳＳ的退化降低，据此提出了ＩＤＳＳ退化失效与快中子注量φｎ之间的解析关键式ｌｎｙ＝ａ＋ｂｌｎφ。     

Atomic force microscopic analysis of hydrogen peroxide bleached kraft northern black spruce fibres

Hydrogen peroxide is a potent, relatively inexpensive oxidant that chemically degrades chromophoric components in pulps and textiles. Oxidation of cellulose is a byproduct of this process step that decreases the tensile strength of individual fibres. The residence time of pulp in the bleaching reactor must be optimized to achieve the desired brightness and minimizing fibre degradation. To evaluate the impact of peroxide bleaching at the microfibrillar level, a single black spruce tree was chosen and kraft pulped. Peroxide bleaching was conducted via benchtop polyethylene bag bleaching in a temperature-controlled waterbath. Atomic force microscopy (AFM) topographical images acquired before and after the bleaching step show dramatic changes in fibre structure consistent with delignification and defects in the surface topography. This was further verified by X-ray work at Brookhaven National Laboratory, NY, U.S.A.     

Engineering Model of a Nonisobaric Heavily Laden Gas‐Particle Jet

An axisymmetrical model of a rapid nonisobaric heavily laden gas‐particle jet is developed. The model is based on the general functions for both axial and radial pressure distributions, which were discovered by a numerical study of rapid gas‐particle jets by the CFD code. The model equations were solved analytically. The results obtained by the model developed are in good agreement with those computed by the CFD code for a wide range of flow parameters.     

ANALYSIS OF EXPERIMENTAL AND NUMERICAL RESULTS OF A TURBULENT SWIRLING FLOW IN A TUBE

In many applications swirling flow is used to enhance heat and mass transfer. One of the problems of modelling a turbulent swirling flow is the choice of the turbulent closure model which is acceptable for engineering purposes. To evaluate which model performs best, numerical results are compared with experimental data. Local velocity measurements are carried out on a swirling flow in a circular tube. The measurement method is hot-wire anemometry combined with visualization techniques. The numerical analysis is carried out using the k-ε model and the Algebraic Stress Model. In the experiment a symmetrical swirl was observed, Comparing the experimental data with the numerical results shows that the Algebraic Stress Model represents the experimental data quite well, whereas the k-ε model fails.