Mapping surface temperature in large lakes with MODIS data

Satellite sensor MODIS on two platforms can produce Sea Surface Temperature over certain regions about three to four times per day. Our objective was to test if the MODIS SST product can be applied for lakes whose surface areas are large enough to be observed at the MODIS spatial resolution and to compare the satellite-derived lake surface temperatures with in situ measurements. Surface temperatures for Lakes Vänern and Vättern in Sweden, two of the largest European lakes, are extracted from the MODIS/Terra images for period 2001-2003. The results are analyzed on different quality levels, as all MODIS L2 products are equipped with an additional quality flag. We present temperature development over 2001-2003, and show the capability of the MODIS SST product to couple the known thermodynamical features in the lakes under study, where temperature varies greatly with space and time. These results can complement lake monitoring programs anywhere.     

Prediction of the effects on dynamic response due to distributed structural modification with additional degrees of freedom

The aim of this study is to investigate means of efficiently assessing the effects of distributed structural modification on the dynamic properties of a complex structure. The dynamic properties of the modified structure can be determined by experimental testing or numerical simulation, both of which are complex, expensive and time-consuming. Assuming that the original dynamic characteristics are already established and that the modification is a relatively simple attachment, the modified dynamic properties may be determined numerically without solving the equations of motion of the full-modified structure. The frequency response functions (FRFs) of the modified structure can be computed by coupling the original FRFs and a delta dynamic stiffness matrix for the modification introduced. The validity of this approach is investigated by applying it to a cantilever beam to which a smaller beam is attached as modification. The original FRFs were obtained experimentally as well as numerically. The delta dynamic stiffness matrix was determined numerically by modeling the attachment and part of the original structure including the attachment points. The FRFs of the modified beam were then computed. Good agreement is obtained by comparing the results to the FRFs of the modified beam determined experimentally as well as by numerical modeling of the complete modified structure.     

Synthesis of poly(4-methylstyrene)- graft-poly(ethylene oxide)s and application as polymeric dispersant in coal-water mixture

Poly(4-methylstyrene)-graft-poly(ethylene oxide)s were prepared via polymerisation of ethylene oxide on to poly(4-methylstyrene)s functionalised with hydroxyl groups. In this way, many ‘comb-like’ polymers having different hydrophobic backbone length, hydrophilic branch length and frequency of branches were synthesised. These polymers were tested as dispersants in coal-water mixtures in order to correlate the dispersing properties of this class of polymers with the investigated parameters.     

Influence of the surface conditions on permeation in the deuterium–MANET system

The condition of the surfaces is of crucial importance for the deuterium permeation through materials. In this work a study of the surface constants for the adsorption (σk₁) and release (σk₂) of deuterium under different surface conditions on the martensitic steel DIN 1.4914 (MANET) has been carried out. The growth of an oxide surface layer (Cr₂O₃) of about 25–30 nm in a MANET sample, heat treated in an oxidizing environment, compared to the bare MANET that have a ‘natural' oxide of about 5 nm has provoked a reduction of both the permeation rate and the recombination coefficient (about 3 orders of magnitude). In addition, the permeation governing process has changed from diffusion-limited to surface-limited. The measurements of the permeation rate of deuterium were performed by a gas-phase permeation technique over the temperature range 574–746 K and for deuterium driving pressures in the range from 3 to 10⁵ Pa.     

Target differentiation with simple infrared sensors using statistical pattern recognition techniques

This study compares the performances of various statistical pattern recognition techniques for the differentiation of commonly encountered features in indoor environments, possibly with different surface properties, using simple infrared (IR) sensors. The intensity measurements obtained from such sensors are highly dependent on the location, geometry, and surface properties of the reflecting feature in a way that cannot be represented by a simple analytical relationship, therefore complicating the differentiation process. We construct feature vectors based on the parameters of angular IR intensity scans from different targets to determine their geometry and/or surface type. Mixture of normals classifier with three components correctly differentiates three types of geometries with different surface properties, resulting in the best performance (100%) in geometry differentiation. Parametric differentiation correctly identifies six different surface types of the same planar geometry, resulting in the best surface differentiation rate (100%). However, this rate is not maintained with the inclusion of more surfaces. The results indicate that the geometrical properties of the targets are more distinctive than their surface properties, and surface recognition is the limiting factor in differentiation. The results demonstrate that simple IR sensors, when coupled with appropriate processing and recognition techniques, can be used to extract substantially more information than such devices are commonly employed for.     

FK6-600牵伸加弹机上“格里森”制齿轮的国产化与改进

对FK6-600牵伸加弹机主传动中"格里森"制圆弧螺旋齿轮的失效情况进行了考察和研究。通过对德国DIN867和我国JB110标准的分析,采用了等顶隙收缩齿并对其进行了合理改进,同时在现场安装工作中采取了必要措施,取得了较好的技术经济效果。     

生产线试运行过程工艺分析软件的应用

介绍了生产线试运行过程中，用工艺分析软件解决所遇到的工艺问题，为工艺分析软件开拓了一个新的应用领域。     

Effect of surface free energy on the adhesion of biofouling and crystalline fouling

Pipelines and heat exchangers using seawater as coolant suffer from biofouling. Biofouling not only reduces heat transfer performance significantly, but also causes considerable pressure drop, calling for higher pumping requirements. It would be much more desirable if surfaces with an inherently lower stickability for biofouling could be developed. In this paper, a cost-effective autocatalytic graded Ni-Cu-P-PTFE composite coating with corrosion-resistant properties was applied to reduce biofouling formation. The experimental results showed that the surface free energy of the Ni-Cu-P-PTFE coatings, which were altered by changing the PTFE content in the coatings, had a significant influence on the adhesion of microbial and mineral deposits. The Ni-Cu-P-PTFE coatings with defined surface free energy reduced the adhesion of these deposits significantly. The anti-bacterial mechanism of the composite coatings was explained with the extended DLVO theory.     

The role of the surface free energy in the selection of a suitable excipient in the course of a wet-granulation method

Pellets containing metronidazole were produced in a centrifugal granulator, with hydroxypropylcellulose (Klucel LF®) as binding agent, and corn starch, microcrystalline cellulose (Vivapur 101®) and lactose as excipients. The wettability of the pharmaceutical powders was assessed by means of contact angle measurements, and the dispersive and polar surface energies were determined. The spreading coefficients, the work of adhesion and the work of cohesion were calculated and correlated with the pellet properties (friability, bulk and tapped density, and porosity). The aim was to investigate the role of the surface free energy of one- and two-component powder compositions in pellet production. The interactions between the particles were found to be connected with the measured pellet parameters. It was concluded that, in the course of the growth of the pellets, the particle sizes of the pharmaceutical powders and the interactions between them are important. If the work of cohesion of the binder is lower than the work of cohesion of the substrate and the work of adhesion, then the optimal amount of the binding agent is that which coats the particles uniformly in minimal quantity and in continuous layer.