STRESS INTENSITY FACTORS AND WEIGHT FUNCTIONS FOR SEMI-ELLIPTICAL SURFACE CRACKS IN FINITE-THICKNESS PLATES UNDER TWO-DIMENSIONAL STRESS DISTRIBUTION

Abstract— A Fourier series approach is proposed to calculate stress intensity factors using weight functions for semi-elliptical surface cracks in flat plates subjected to two-dimensional stress distributions. The weight functions were derived from reference stress intensity factors obtained by three-dimensional finite element analyses. The close form weight functions derived are suitable for the calculation of stress intensity factors for semi-elliptical surface cracks in flat plates under two-dimensional stress distributions with the crack aspect ratio in the range of 0.1 ≤ a/c ≤ 1 and relative depth in the range of 0 ≤ a/t ≤ 0.8. Solutions were verified using several two-dimensional non-linear stress distributions; the maximum difference being 6%.     

液相颗粒包裹法制备PbNb2O6微粉的研究

本文介绍了一种采用液相颗粒包裹技术制备功能陶瓷微粉的新方法.这种方法有如下特点:(1)方法简便,不需要特殊的设备,便于扩大应用于工业生产;(2)粉体颗粒尺寸小而均匀;(3)粉体化学组成偏离小、且均匀;(4)适应性强,从双组分至十多组分的材料微粉制备均可采用;(5)特别适用于一些含有难溶组分、用液相法无法制备的材料.本工作采用这一方法,成功地制备出 PbNb_2O_6微粉,其平均腰粒尺寸<0.5μm,分散性及化学均匀性好,烧结活性高,烧结温度可以降低近100℃,瓷坯密度可达理论密度的96%以上.     

荷能束辐照致使Cu/Ag表面偏析的研究

本文研究了金属(Cu)/金属(Ag衬底)系统的荷能束辐照引起的表面偏析现象。观察到Cu在多晶Ag衬底上溅射淀积过程中,Ag原子在Cu膜表面的偏析,且淀积Cu原子能量越大,Ag原子偏析程度越大,即观察到了淀积Cu原子10~(-1)～1eV量级的平均能量差异对膜层表面偏析行为的影响。对溅射淀积所得膜层进行keV量级的离子束辐照,Ag原子的表面偏析程度更甚。     

Evolutionary algorithms and de novo peptide design

One of the goals of computational chemistry is the automated de novo design of bioactive molecules. Despite significant progress in computational approaches to ligand design and efficient evaluation of binding energy, novel procedures for ligand design are required. Evolutionary computation provides a new approach to this design issue. This paper presents an automated methodology for computer-aided peptide design based on evolutionary algorithms. It provides an automatic tool for peptide de novo design, based on protein surface patches defined by user. Regarding the restrictive constrains of this problem a special emphasis has been made on the design of the evolutionary algorithms implemented.     

回转头技术在表面贴装设备中的应用

当今的回转头式贴装设备能够以相对低廉的价格 ,提供高速度和准确的贴装 ,以及先进的识别操作。     

Interpolating Quintic Polynomial with C~1 Continuity

A method constructinq C~1 Piecewise quintic polynomial over a triangular grid to interpo-late function values and partial derivatives at vertices is presented in this paper.The set of precise poly-nomials of this method is discussed.     

Inhibition of acid rock drainage from uranium ore waste using a conventional neutralization and precipitation treatment

Glass columns (length 50 cm, i.d. 4 cm) containing 900 g of uranium ore waste were subjected to a three-step process: (1) acid drainage generation, (2) neutralization and precipitation treatment and, again, (3) acid drainage generation. In the first acid generation step, lasting about one year, different variables (pyrite addition, inoculation and irrigation solution) were tested by measuring effluent pH, redox potential, total iron and sulphate. Conditions of acid generation were satisfactorily reproduced, reaching stable pH values around 2.0 that were determined mainly by pyrite addition and the type of irrigation solution used (distilled water or ferrous sulphate). The neutralization and precipitation treatment consisted of alternating irrigations of a neutralizing solution (CaO saturated plus NaOH) and a precipitating solution (ferric sulphate saturated). This treatment caused accumulation of basic iron sulphate and iron oxide precipitates according to SEM studies. After this treatment, the barrier effect created by the reaction products was checked, using irrigation solutions similar to the first step. The effluents collected showed higher pH and lower redox potential, total iron and sulphate values than those observed before the treatment, evidencing inhibition of acid drainage generation.     

Effects of Surface Concentration on Drying Behavior of Carbohydrate Solutions

As the surface properties of the drying materials are very important not only for the drying rate but also for the quality change during drying, the effects of surface concentration on the drying behavior of liquid foods (sugar solutions) were investigated by isothermal drying experiments and by numerical calculation experiments. The isothermal drying experiments with gelled sugar solution systems (sucrose and maltodextrin) were carried out at various relative humidity (RH) values (RH = 0 to 84%). Separate experiments were carried out for determination of the desorption isotherms.

The isothermal drying curves of sugar solutions at RH = 0 to 51% were very similar. Numerical simulations also showed that the drying curves of these sugars at the surface concentration = 0 and 0.1 are almost the same, although the concentration distributions are different.

When a small amount of gelatin was added to sugar solutions, the drying rate decreased remarkably as the gelatin might form a thin film (skin) near the surface, and consequently the retention of ethanol increased.     

Investigation of the structure and properties of modified Armenian minerals for polymer-based composites

The results of investigation of the modification of the Armenian minerals with fluorine-containing oligomers show that a modified product appears when the mineral fillers are treated with fluoroalkanes. The product preserves the structure of the fillers with a “grafted” fluoroalkane layer in which chlorine atoms locate mainly over their periphery. The composite materials based on heterochained polymers and the modified fillers possess a stronger wear resistance and a low friction coefficient.     

Effect of Wall Surface Properties at Different Drying Kinetics on the Deposition Problem in Spray Drying

Current methods in alleviating the wall deposition problem in spray drying emphasize mainly controlling the stickiness of the drying particles and less attention is placed on the properties of the dryer wall. In this experimental study, the effect of wall surface properties on the deposition mechanism has been investigated. Properties considered in classifying different wall materials were surface energy, roughness, and dielectric properties. The model solution contained sucrose, representing low-molecular-weight sugars commonly encountered in spray drying of fruit and vegetable juices. The effect of wall properties on deposition was explored at different drying rates producing particles of different surface rigidity. Larger surface roughness produced higher deposition fluxes for particles with high impact velocity and moisture. Surface energy and surface roughness were found to have no significant effect for dry rigid particles at the middle and bottom elevation of the drying chamber. However, material with lower surface energy (Teflon) exhibited less deposition for rubbery particles at such elevations. Analysis shows that dielectric wall material (Teflon) tends to enhance deposition of dry particles because of attrition at the surface. Higher wall temperature was found to produce slightly more deposition. The results of this work give a general indication of the effect of wall material on the deposition problem and provide the fundamental understanding for further studies along this line. Proper selection of dryer wall material will provide potential alternatives for reducing the deposition problem.