Characterization of resol resins modified by the addition of PVC plastisols

Plastisols, which are a blend of poly(vinyl chloride) resin and a plasticizer (DEHP), were used as a toughening agent of a resol resin in order to improve the mechanical properties. It was not possible to formulate resol blends by adding more than 10 % of plastisol owing to a lack of apparent homogeneity in the systems, which also showed many air bubbles. The relationship between dynamic mechanical, mechanical and thermal properties and the amount of plastisol added was studied. It was determined from the infrared spectroscopy and dynamic mechanical results that the resol–plastisol blends seem to be formed by a reaction between the phenol and PVC giving a higher crosslinked structure. An improvement in the thermal resistance of the blends at lower temperatures was observed with an increase in the percentage of plastisol. Flexural analysis showed the elastic behaviour of the systems. However, it was not possible to observe the effect of the plasticizer (DEHP) owing to the low quantity of plastisol that was added to the resol. Copyright © 2004 Society of Chemical Industry     

Conducting composites of polythiophene and polyfuran with acetylene black

Conducting composites of polythiophene (PTP) and polyfuran (PF) with acetylene black (AB) were prepared via chemical oxidative polymerization of thiophene and furan in a suspension of AB in CHCl₃ at room temperature using anhydrous FeCl₃ as the oxidant. Formation of PTP and PF and their subsequent incorporation in PTP–AB and PF–AB composite systems were confirmed by FTIR analysis. Scanning electron microscope analysis showed the presence of compact clusters of particles in both composites. Transmission electron micrographs of PTP–AB and PF–AB composites showed formation of globular polymer encapsulated AB particles with average diameters of the order of ～100 nm in both systems. Thermogravimetric analysis revealed that the overall thermal stability varied in the order: AB > PTP–AB > PTP and AB > PF–AB > PF. DC conductivity values for the PTP–AB and PF–AB composites were of the order of 10^?2 and 10^?3 S cm^?1, respectively. Copyright © 2004 Society of Chemical Industry     

Existence, uniqueness and stability of the equilibrium points of a SHARON bioreactor model

This paper addresses the dynamics of a SHARON reactor, a promising technology for ammonium removal from concentrated wastewater streams. The contraction mapping theorem is used to determine which operating conditions of a SHARON reactor with pH-control result in a unique equilibrium state. However, this approach only identifies the case of very large dilution rates, in practice corresponding with complete biomass wash-out, i.e. with complete loss of biological activity. Practical operation of a SHARON reactor aims at reaching ammonium conversion to nitrite. To identify such interesting operating points, the equilibrium points are subsequently calculated directly in terms of input variables for a simplified SHARON reactor model. The stability of the obtained equilibrium points is assessed and the corresponding phase portraits are analyzed. The influence of slightly varying parameter and input values is investigated as well.     

Role of Specimen Geometry in the Effect of Fiber Orientation on the Thermal Conductivity of a Uniaxial Carbon-Fiber-Reinforced Aluminoborosilicate Glass-Matrix Composite

A study concerning the effect of fiber orientation on the thermal conductivity of a uniaxial carbon-fiber-reinforced borosilicate glass was conducted. For thin specimens, and thick specimens with specimen sides cut parallel to the fiber direction, the dependence of thermal conductivity on fiber orientation showed excellent agreement with theoretical behavior predicted for a composite infinite in extent. In contrast, the thermal conductivity data for rectangular thick specimens fell well below the data for the thin and angled specimens. For fiber orientation of 45° and higher, at which the heat was directed toward the side of the specimen rather than across, the thermal conductivity values showed excellent agreement with theoretical behavior predicted for a finite composite strip with insulated sides.     

Application of boundary element method to 3-D problems of coupled thermoelasticity

This paper deals with a new boundary element method for analysis of the quasistatic problems in coupled thermoelasticity. Through some mathematical manipulation of the Navier equation in elasticity, the heat conduction equation is transformed into a simpler form, similar to the uncoupled-type equation with the modified thermal conductivity which shows the coupling effects. This procedure enables us to treat the coupled thermoelastic problems as an uncoupled one, A few examples are computed by the proposed BEM, and the results obtained are compared with the analytical ones available in the literature, whereby the accuracy and versatility of the proposed method are demonstrated.     

热分析在PVA纤维预处理中的应用

用差热、热重法对原丝的热性能及由不同预处理方法所引起的PVA纤维的热行为变化进行了研究;并通过模拟脱水条件,用不同升温速率,求出了经不同预处理纤维的脱水反应活化能。结果表明,PVA原丝在230℃有一软化点,三种预处理都不同程度地影响了原丝的热效应变化;纤维在180～340℃主要为脱水反应;原丝及经脱水剂、O_3和O_3综合脱水剂处理的纤维,其脱水反应的表观活化能分别为:164.3kJ/mol,92.9kJ/mol,130.5kJ/mol和117.6kJ/mol。     

Some experimental findings in compression-after-impact (CAI) tests of CF/PEEK (APC-2) and conventional CF/epoxy flat plates

Compression-after-impact (CAI) tests have been conducted for quasi-isotropic thick plates with 48 plies by using the NASA method and on plates with 32 plies by using the SACMA method. Specimens are made of CF/PEEK (APC-2) and conventional CF/epoxy for the NASA plates and CF/epoxy for the SACMA plates. In the NASA CAI tests, the sequence of delamination buckling and its propagation is clearly revealed through various experimental techniques. One major technique is moiré topography, and the other is thermo-mechanical stress analysis with a high-accuracy infrared sensor. The arrest of delamination propagation just before catastrophic failure due to high fracture toughness is clearly captured by the moiré camera. This behavior provides good CAI values of CF/PEEK. The initial buckling properties of the delaminated region by the impact are then extensively discussed. Numerical predictions of initial buckling stress have been obtained by modelled geometry of the delaminated region simplified from its precise structure clarified by ultrasonic C-scanning. They agree fairly well with the experimental results. The in-plane stress distribution in the delaminated region before initial buckling is measured by an infrared stress graphic system. This compared favorably with finite element predictions. Two types of symmetric buckling modes with respect to the central plate surface, twin and single peak ones, are experimentally captured.     

Adhesive Dispensing Process Analysis: Steady-State Dispensing of One-Component Adhesives

The process of dispensing one-component heat-cure adhesives was investigated in order to understand current application processes and to guide new process development. Typical one-component adhesives exhibit non-Newtonian rheological behavior, and hence Newtonian fluid mechanics does not adequately describe the dispensing process. In the present study, the adhesives were modeled as Bingham fluids possessing a yield stress and a steady state viscosity. The model of the dispensing apparatus includes four major flow sections connected in a serial configuration. The fluid mechanics equations derived for Bingham fluids in the individual flow sections were solved by numerical methods in order to understand the interrelationships between the material variables (e.g. yield stress, viscosity, temperature dependencies) and process variables (e.g. pressure, flow geometry, temperature, output). The concept of the model is generic and the details of the model can be modified for any forced-flow adhesive application process.

The adhesive flow properties significantly influence the process output. Dispensing temperature, among the process variables, has the strongest effect on process output. A ± 1.0·C perturbation in the dispensing temperature can cause as much as a 14% variation in the bead size for the range of adhesives studied. Differences in flow characteristics result in differences in processability and non-linear temperature/pressure sensitivity. The non-linear sensitivity can be eliminated by operating the dispensing process isothermally. Finally, the process limits for one-component adhesives, which are susceptible to chemical instability induced by viscous heating during processing, are defined and discussed in terms of a modified Brinkman number that takes into account viscous dissipation, heat conduction and convection, and chemical stability of the material during processing.     

Time‐dependent heat transfer coefficient of a wall

A time‐dependent coefficient of heat transfer is proposed for the computation of thermal power required, so that a room temperature reaches a desired value within a given time. A mathematical formulation of the room heating transient phenomenon is constructed in a dimensionless form. Using an integral approximate solution an analytical expression for this coefficient is provided and it is verified by diagrams adopted by DIN 4701. Copyright © 2003 John Wiley & Sons, Ltd.     

A simplified method for modelling the effect of blinds on window thermal performance

An approximate method is presented for predicting the effect of a louvered blind on the centre‐glass thermal performance of a fenestration. The method combines a one‐dimensional heat transfer model with data from a numerical simulation of the window and blind. Sample results for a blind mounted on the indoor surface of a window show the effect of blind slat angle on heat transmission. Both summer and winter conditions are considered. The results show that a louvered blind can improve the U‐value of a standard double‐glazed window by up to 37%. Also, the radiation heat exchange with the room can be dramatically reduced (by up to 60%), which will improve the level of occupant comfort. However, there was found to be a trade‐off between U‐value and occupant comfort; placing the blind closer to the window improves the U‐value, but increases the radiation heat exchange with the room. The predictions from the present simplified method compare well with results from a full two‐dimensional computational fluid dynamics solution of the conjugate blind/window interaction. Copyright © 2005 John Wiley & Sons, Ltd.