压力传感器静态检定装置的测量不确定度

本文根据压力传感器（静态）国家计量检定规程，对压力传感器静态检定装置进行误差分析，得出该装置的测量不确定度。最后，通过实例说明实际测量不确定度与理论分析相符合。     

Steady-state torque control system with secondary-current feedback for three-phase squirrel-cage induction motors

This paper presents a highly stable steady-state torque control system with a feedback of a secondary current signal. The torque control system is constructed with a feedback of the secondary current (I₂) signal using a quick response magnetic-field sensor constructed with an amorphous core multivibrator bridge, which can solve the secondary resistance change problem for temperature variation in the IM. Moreover, we added a state feedback to the system to improve the response speed for the unit step function of a torque order. The I₂ sensor method has advantages especially at a low-speed range, in which conventional method using an integrator shows control errors.     

非协调h－p型有限元补偿法

详细讨论了非协调ｈ－ｐ型有限元的补偿法，给出了令人满意的收敛阶．     

Early detection of ageing in solder joints through laser probe thermal analysis of the peltier effect

We have recently developed an optical contactless method for testing the quality of solder joints during accelerated thermal cycling ageing processes.¹ The method was based upon the measurement of the dynamic thermal behaviour of the joint to short bursts of Joule heating. It has proved to be efficient in revealing the formation of cracks at the lead-solder interface. We present a method to evaluate ageing at a much earlier stage in the cycling process. We have observed in earlier work,¹ that before cracks appear, structural changes occur in the solder at the lead-solder interface. The thermal response of the solder joint is recorded over time to a Peltier heat perturbation produced by flowing a current pulse through the interface where structural changes occur. The key point in this method is to discriminate the Peltier effect from the Joule thermal response because both effects generate heat. The variation of the early Peltier response in the thermal cycling ageing tests is seen as a quantitative signature of the structural changes in the lead-solder interface.     

Thermal Characterization of 1.3 μm InAsP/InGaAsP Ridge Waveguide MQW Lasers Based on Spectroscopy Method

An experimental way to analyze the thermal characterization of semiconductor lasers based on spectroscopy method under pulse driving conditions has been developed. By using this way the thermal characteristics of strain compensated 1.3 μm InAsP/InGaAsP ridge waveguide MQW laser diodes have been investigated. Results show that by measuring and analyzing the lasing spectra under appropriate driving parameters and temperature ranges, the thermal resistance of the laser diodes could be deduced easily. A higher thermal resistance of 640 K/W has been measured on a narrow ridge laser chip without soldering. Other thermal and spectral properties of the lasers have also been measured and discussed.     

红外热成象技术在股骨头坏死疾病针刺疗法中的应用

红外热成象技术可以有效地用于股骨头坏死疾病的诊断和针刺治疗效果的评价，效果优于其它常规方法。     

半绝缘砷化镓中碳含量对热稳定性的影响

本文报导了LEC法半绝缘砷化镓单晶中含碳量对SI-GaAs热稳定性的影响。在800℃以上退火,发现当晶体中C含量大于1.5×10~(16)cm~(-3)时,SI-GaAs的热稳定性变差;而C含量小于5×10~(15)cm~(-3)时,通常表现出良好的热稳定性。     

本征吸除硅片特性研究

本文描述硅本征吸杂片的特性参数,如吸除区宽度、洁净度,氧沉淀密度、MOS电容寿命,介绍了表面态密度及残余间隙氧浓度的检测方法和工艺对参数的影响及参数之间的内在联系,文章还实验论证了不同参数水平对器件成品率的影响,建立了以MOS电容寿命为主导的参数控制方法,利用本文提供的控制参数,可使CCD-512器件成品率达60％,以上优品率≥85％。