铜铅锌银多金属矿湿法分离新工艺

依据不同金属硫化物氧化分解电位的差异 ,针对某含铜、铅、锌、银复杂多金属硫化矿的难选冶特性 ,对浮选获得的混合精矿采取在线控制浸出过程氧化还原电位的方法 ,分步选择性氯化浸出各有价元素 ,并辅之以沉淀、置换、萃取等工艺 ,使有价金属以较高的回收率得到了有效的分离提取 ,在各工序最佳条件下 ,Cu、Pb、Zn、Ag各金属的浸出率均大于 99 0 % ,元素硫的回收率大于 76%     

The influence of the fabrication process on the buckling of thin-walled steel box sections

Steel box sections are usually fabricated from flat plates which are welded at the corners. The welding process can introduce residual stresses and geometric imperfections into the sections which can influence their strength. For some thin-walled sections, large periodic geometric imperfections have been observed in manufactured sections. Subsequent investigations have indicated that the imperfections are in fact buckling deformations i.e. the box section has buckled due to welding residual stresses prior to any application of external load. The welding procedure and the behaviour of the box sections under load has been modelled using a finite element analysis that accounts for both geometric and material non-linearities. Tests have been carried out on box sections with a range of width to thickness ratios for the plate elements. Modelling has been shown to give good correlation with the test results. The conditions for buckling to take place as a result of the welding process have been established. A design method has been proposed.     

Chemical leaching and magnetic properties of non-equilibrium Al(Co–Cu) powders produced by rod milling

We report upon the chemical leaching and magnetic properties of nanoscale crystalline Al_0.6(Co₂₅Cu₇₅)_0.4 alloy powders produced by rod milling. X-Ray diffractometry (XRD), transmission electron microscopy, differential scanning calorimetry, vibrating sample magnetometry, and superconducting quantum interference device magnetometry were used to characterize the as-milled and leached specimens. After 400 h of milling, only the b.c.c. phase of the intermetallic compound γ-Al_3.892Cu_6.10808 was detected by XRD. After annealing the leached specimen at 600 °C for 1 h, the nanoscale crystalline phase was transformed into the f.c.c. Cu phase, and this was accompanied by a change in the magnetic properties. The peaks of the magnetization shifted towards lower temperature with increasing external field. The temperature behavior at T_f (45 K) for direct current (d.c.) magnetic susceptibility measurements was quite different for field cooling and zero-field cooling. After cooling the leached specimen from 800 °C, magnetization increased gradually.     

全球趋向统一的《粉末冶金零件材料规范》

评述了ISO 5 75 5“烧结金属材料—规范”和美国MPIF标准 35的变迁和趋向统一。阐述了“最小强度值”的意义。说明了我国粉末冶金结构零件材料标准的现状     

高热流密度电加热元件

本文论述了用于液态金属钠热工水力性能研究的高热流密度模拟电加热元件的结构特点、材料选择、热电偶设置及其他与棒束传热实验研究有关的问题。     

长距离钢带传动的张紧机构设计与应用

比较了几种长距离传动方式的特点与适用场合，重点探讨了实现长距离精密传动的技术要点。结合实际工程，完成了长距离钢带精密传动的应用，并指出张紧机构的设计与应用是钢带实现长距离精密传动的关键。为此文中对钢带传动的典型张紧机构进行了比较，并分析了这几类张紧机构的应用情况，有参考和应用价值。     

用膜电解法处理低浓度SO2吸收液的三室电解槽材料的选择

提出了用膜电解法处理低浓度SO2吸收液的方法，介绍了三室电解槽的设计原理及在电场作用下，电解槽内离子的迁移和电解反应机理，系统地讨论了电解槽组成单元材料（如阳离子交换器）的选择及在H2SO4－NaHSO3-Na2SO3体系中金属阳极的选择等，并进行了试验验证，得到了很好的结果。     

Organic Materials and Thin‐Film Structures for Cross‐Point Memory Cells Based on Trapping in Metallic Nanoparticles

Non‐volatile solid‐state memory cells based on composites of metal nanoparticles and polymers are embedded in organic semiconducting host materials. This paper presents data from a wide range of materials and device structures and shows that the switching phenomenon is commonly observed.     

不饱和烃硅氢加成催化剂固载化研究进展

综述了各类负载过渡金属的催化剂体系及其在不饱和烃硅氢加成反应中的应用。负载过渡金属的催化剂具有良好的可回收性和选择性，研究主要集中在开发价廉、使用安全、环境友好和高催化性能的活性炭、氧化物或有机聚合物等负载过渡金属催化剂，并取得很好的结果。