控轧控冷工艺对高强度锚杆钢组织和性能的影响

随着矿井深度的增加,对锚杆支护强韧性的要求越来越高,为了应对这一情况,需要研发出更高强度的锚杆钢。利用锚杆钢研究了轧制工艺、冷却工艺与珠光体、铁素体相比例,析出相析出行为及力学性能的关系。研究结果表明,在中轧后、精轧前采用适当水冷+回复段处理的复合工艺可使晶粒更细小、组织更均匀。对超高强度锚杆钢进行热压缩变形试验,由热模拟试验结果确定相转变温度为A_c1=737 ℃、A_c3=886 ℃。最终筛选出入精轧温度为810 ℃、回复段温度为800 ℃时,可获得的晶粒尺寸达4 μm,珠光体体积分数为66.8%,铁素体体积分数为33.2%,珠光体片层间距达200 nm;另外调整V、Cr、N等析出以提高锚杆钢的强韧性,较低的回复温度有利于细小、弥散、V(C/N)析出相的析出,V(C/N)的析出可进一步改善锚杆钢的力学性能。由该控轧控冷工艺轧制的锚杆钢屈服强度为780 MPa、抗拉强度为930 MPa、硬度为291HV、伸长率为20%。     

Stress relaxation behavior of Ti-6Al-4V alloy

1　INTRODUCTIONTi 6Al 4VisoneofthemostimportantTial loys[1,2 ] .Butthisalloyhasbadformabilityforitshighelasticresilience .Therefore ,hotsizingisimpor tant[36 ] .Asthebaseofhotsizing ,thestudyofstressrelaxationhasimportanttheoreticalvalueandpracticalsignificance .Ontheotherhand ,Ti 6Al 4Visusedasfastenermaterialssometimes .Whenthefastenersworkatthetemperaturehigherthanroomtemperature ,stressrelaxationmayresultsinacci dents .Sohowtopreventthestressrelaxationisveryimportant[7] .Uptonow ,…     

3Cr2W8V钢锻件表面裂纹的成因及预防措施

通过对难变形钢3Cr2W8V进行实验,证明了合理地选择锻造工艺参数,也是解决表面裂纹的重要途径之一。     

Study On the Tribological Behavior of the Arc-added Glow Discharge Plasma Non-hydrogen Carburization On Titanium Alloy Surfaces

This paper introduces a new titanium alloys surface strengthening treatment by using the arc-added glow discharge plasmas non-hydrogen carburization technique. High purity and high strength graphite is selected as cooling cathode arc source for supplying carbon atoms and particle, which migrate to the titanium alloy(Ti6Al4V) surface and form modified layer. Thus, the hydrogen embrittlement is avoided while the tfibological behavior of the titanium alloy surface is improved in the respects of anti-friction and anti-wear ability.The tribological behavior of the modified layer under dry sliding against SAE52100 steel was evaluated on a ball-on-disc test rig. The results showed that the modified layer obtained a thickness of 30μm at 980℃, 30minutes. The microhardness of the Ti6Al4V alloy surface attained 936 HV, which was much larger than that of the Ti6AI4V alloy. The Ti6AI4V alloy was characterized by adhesion wear and scuffing under dry sliding against the steel, while the surface modified layer experienced much abated adhesion wear and scuffing under the same testing condition. This could be attributed to the carbon dement with different modalities exists in the modified layer.The modified layer showed good friction-reducing and fair anti-wear ability in dry sliding against the steel. Using the SEM,XRD and XPS, the phase structure and morphology of the carburization modified layer was analyzed.     

V形件弯曲凹模最小深度的确定

该文指出了目前广泛使用的经验查表法确定V形件弯曲凹模深度的不合理性，分析了凹模斜壁的作用及其与圆角半径的相互关系，提出了凹模最小的深度的概念和计算公式。     

U形件弯曲影响回弹因素模拟分析

板材在弯曲过程中存在的最突出的问题是弯曲回弹难以精确控制.弯曲卸载后产生的回弹,使弯曲件的形状和尺寸与模具工作部分的形状和尺寸不符.弯曲件的最后形状与整个变形过程有关,模具几何参数、材料性能参数等都会对回弹产生很大影响.在板材弯曲成形智能化控制系统中,准确确定实时识别和预测模型的输入、输出参数是弯曲智能化控制的成功与否以及回弹控制精度高低的关键.本文采用Ls-dyna软件,对U形件弯曲影响回弹的因素进行了分析,得出了影响回弹规律的主要因素.为U形件弯曲智能化控制神经网络参数识别及预测模型输入、输出参数的选择提供依据.     

一种检测电火花加工间隙状态的柔性方法

介绍了一种在数控电火花加工脉冲电源中实现间隙状态检测的柔性方法，具有阈值设置柔性、状态识别准确的特点，巧妙地用一个稳压二极管的钳位作用提高了间隙状态识别的精度，非常适合需经常改变加工参数的加工实验使用。     

Effect of cold spray deposition of a titanium coating on fatigue behavior of a titanium alloy

The deposition of titanium on a titanium alloy substrate is being examined for potential use as a surface treatment for medical prostheses. A Ti6Al4V alloy was coated with pure titanium by cold gas dynamic spraying. Coatings were deposited onto samples with two different surface preparation methods (as-received and grit-blasted). The fatigue life of the as-received and grit-blasted materials, both before and after coating, was measured with a rotating-bend fatigue rig. A 15% reduction in fatigue endurance limit was observed after application of the coating to the as-received substrate, but no significant reduction was observed on its application to the grit-blasted substrate. The reduction in fatigue endurance limit has been related to the substrate-coating interface properties, the elastic modulus, and the residual stress states. This article was originally published inBuilding on 100 Years of Success, Proceedings of the 2006 International Thermal Spray Conference, (Seattle, WA), May 15–18, 2006, B.R. Marple, M.M. Hyland, Y.-Ch. Lau, R.S. Lima, and J. Voyer, Ed., ASM International, Materials Park, 2006.     

Enhancement by SO2 of initial activity for selective catalytic reduction of NO with CH3OH over \gamma-alumina

The effect of SO₂ on catalytic activity for NO reduction to N₂ by methanol in excess oxygen over $\gamma$ -alumina has been investigated. SCR activity increased initially upon exposure of a fresh $\gamma$ -alumina catalyst to SO₂ which is attributed to formation of Brønsted acid sites. Longer exposure to SO₂ leads to a decline in catalytic activity to a lower steady-state NO_x reduction activity which is independent of the SO₂ content in the feed gas.