FTIR investigation of ethylene coordination and polymerization on reduced Cr/SiO2 catalyst

FTIR spectroscopy was applied to study the initial steps of ethylene polymerization on reduced chromia-silica (0.5 wt% Cr/SiO₂). To decrease the speed of the reaction small doses of gas were introduced to the catalyst in each run and C₂D₄ was used to confirm band assignments. At the initial steps of the reaction only ethylene molecules coordinated to probably Cr _A ²⁺ cations were observed. The concentration of such complexes was estimated to be about 50% of the total amount of Cr atoms in the sample. The FTIR spectrum of the polymer formed at the initial doses of C₂H₄ (when [C₂H₄] [Cr]) was found to be slightly different from that formed after excess ethylene was introduced onto the catalyst ([C₂H₄] > [Cr]).     

基于J2EE平台的供应链管理系统研究

介绍了供应链管理的基本原理和实现技术，从平台基础、移植性、扩展性等多个角度对J2EE平台进行了相应的分析，提出了一个基于J2EE平台的供应链管理系统框架，并从系统结构、系统功能模块等方面进行了说明。     

低电压氧化锌压敏电阻器的研究

研究了一种制造低电电压氧化锌压敏电阻器的方法。在基本成分的基础上适当加入二氧化钛可降低梯度电压（Ｖ１ｍＡ／ｍｍ），适量掺硼和改进热处理工艺可减小元件的漏电流和提高其稳定性。     

Site occupations and ordering behaviour of O phase in Ti2AlNb—based intermetallics

1　ＩＮＴＲＯＤＵＣＴＩＯＮＴｈｅｏｒｔｈｏｒｈｏｍｂｉｃａｌｌｏｙｓａｒｅｏｆｇｒｅａｔｔｅｃｈ ｎｏｌｏｇ ｉｃａｌｉｎｔｅｒｅｓｔｉｎｈｉｇｈｔｅｍｐｅｒａｔｕｒｅａｐｐｌｉｃａｔｉｏｎｓｓｉｎｃｅｔｈｅｙｈａｖｅａｇｏｏｄｂａｌａｎｃｅａｍｏｎｇｓｔ     

石英砂的相变与换向器套筒铸件的变形

用呋喃树脂石英砂工艺生产牵引电机换向器套筒出现变形、裂纹等铸造缺陷,是由石英砂相变膨胀引起,后用高铬刚玉砂代替石英砂得到解决.     

The generation of surface roughness during slurry erosion-corrosion and its effect on the pitting potential

Results of experiments performed to isolate the effect of surface roughness generated during slurry erosion-corrosion of 304L stainless steel are presented. Surfaces prepared by grinding to different finishes show that increasing the roughness lowers the pitting potential in chloride solution. Subsequent erosion by an aqueous sand slurry then alters this pitting potential (E_p), as measured in the solution phase alone, in a manner dependent on the initial surface roughness. Surfaces which were initially rougher show a pronounced rise in _p after erosion, while those with an initially smoother finish show a fall in E_p after erosion. Measurement of E_p during erosion-corrosion does not fit either process, with values of _Ep lower than those predicted from the surface roughness alone.     

Characterization of ultrafine La x Sr1−x MnO3 powder prepared by spray pyrolysis

The characterization of La _x Sr_1−x MnO₃ powders produced by spray pyrolysis using scanning electron microscopy (SEM) and transmission electron microscopy (TEM) observation, specific surface area (Brunauer-Emett-Teller), and particle size distribution measurements shows that the resultant large particles are loose agglomerates consisting of many small particles. However, the sintered tiny particles can form hard agglomerates, and the particle size increases remarkably. The structures of the powders before and after sintering were identified by x-ray diffraction (XRD). The study of the electrical property of the powder shows that the powder is a metallic conductor. In a reducing atmosphere, the powder can be decomposed. When the powder is cofired with yttria-stabilized zirconia 5% (YSZ) powder at 1200 °C for 5 h, no new phase is produced, and the powder remains a single provskite hexagonal-rhombohedral structure.     

使用Visual C+ +实现串行通讯

以VisualC 为工具，探讨了在RS-232C接口协议下DTE设备之间通讯的实现问题。     

Conductivity enhancement in transparetn ZnO films via Al-dopping produced by CW-CO2 laser-induced evaporation

Highly conductive transparent aluminium-doped ZnO (ZnO:A1) films were successfully deposited by CW-CO₂ laser-induced evaporation. Optimisation of evaporation parameters was based on laser power, substrate temperature, O₂ partial pressure in the vacuum chamber and amount of Al in the ZnO source pellet. ZnO:A1 films with an electrical resistivity as low as 6.6 × 10⁻²Ω·cm and an optical transmission of 80% at 500nm were obtained at laser power of 15 W, substrate temperature of about 200°C, O₂ partial pressure of 6—7 × 10⁻⁴ Torr and 5wt.% Al. Conductivity of ZnO films can be increased one order via Al-doping in ZnO films. The films obtained by laser-induced evaporation have compared quite favorably with the high quality films obtained by sputtering.     

碳纳米管及稀土元素钇(Y)对高Ni含量Ti(C,N)基金属陶瓷组织与性能的影响

研究了不同含量的碳纳米管及0.8%稀土Y对高Ni含量Ti(C,N)基金属陶瓷组织性能的影响.将不同成分的试样分别于1400℃、1410 ℃、1420℃真空烧结,测试抗弯强度、洛氏硬度,观察背散射电子形貌、断口形貌并做能谱分析.结果表明,加入质量分数(下同)为0.8%Y及0.3%～1.0%的碳纳米管时,碳纳米管含量为0.5%的组织较均匀,芯壳结构明显,抗弯强度及硬度均较高.