溶胶-凝胶法制备(Sr,Pb)TiO3纳米晶粉及表征

采用溶胶－凝胶法成功地合成了（Sr,Pb)TiO3纳米晶粉，并利用FTIR技术对凝胶的形成过程及350℃，1．5h煅烧获得的粉体材料进行了表征。实验以TG－DSC分析作为拟定煅烧温度的依据，以XRD作为煅烧产物的分析手段，最佳煅烧温度为600℃，所合成的（Sr,Pb)TiO3纳米晶粉的平均晶粒尺寸约为21nm，属钙钛矿型立方顺电相结构。     

Pre-bainitic Transformation in Fe-Ni Alloy

Ｔｈｅｐｒｅ－ｂａｉｎｉｔｉｃｐｈｅｎｏｍｅｎｏｎｉｓｏｎｅｏｆｔｈｅｉｍ－ｐｏｒｔａｎｔｓｕｂｊｅｃｔｓｏｆｂａｉｎｉｔｉｃｔｒａｎｓｆｏｒｍａｔｉｏｎｗｈｉｃｈｉｓｓｔｉｌｃｏｎｔｒｏｖｅｒｓｉａｌ．Ｏｎｅｖｉｅｗｉｓｔｈａｔｔｈｅｓｏｌｕｔｅａ...     

烧结直接淬火对WC－TiC－Co合金WC相微观结构及力学性能的影响

本文以ＴＥＭ和ＸＲＤ为主要手段，研究ＷＣ－ＴｉＣ－Ｃｏ硬质合金（ＹＴ１４）在直接淬火后ＷＣ相的微观结构和微观应力，比较了常规烧结态与淬火态试样ＷＣ相之间的差异，探讨了直接淬火对合金力学性能的影响。结果表明，在保持合金其他性能不降低的同时，直接淬火的抗弯强度比常规烧结提高２８％左右。并首次发现，经直接淬火热处理的ＹＴＩ４合会中与Ｃｏ相相邻的ＷＣ晶粒边界出现滑移台阶，这是淬火过程中热应力使ＷＣ晶粒内位错在｛０００１｝密排面聚集，并可能沿｛０００１｝＜１１２０＞易滑移系统强滑移的结果。直接淬火试样的微观应力比重新加热淬火的低。     

Thermal expansion of Pyros from 20 to 1273 K

Pyros, which is a Ni-base alloy (82% Ni, 8% Cr, 4% W, 3% Mn, and 3% Fe), has been used extensively in France since 1926 as a temperature sensor and as a reference material for thermal expansion measurements. In this paper we present recent data on the expansion and expansivity of Pyros from 20 to 1273 K. Expansivity results, obtained by taking the derivative of a cubic-spline polynomial fitting performed to the L/L experimental data, show that Pyros is a stable material in the 20 to 1273 K temperature range. Furthermore, since the expansivity values are similar to those of steels, Pyros should be of special interest to laboratories which are concerned with expansion measurements on steels. Therefore, we suggest that Pyros be considered as a suitable reference material for thermal expansion measurements on steels, and until more accurate results are obtained, we propose our results as reference data between 20 and 1273 K.Paper presented at the Ninth Symposium on Thermophysical Properties, June 24–27, 1985, Boulder, Colorado, U.S.A.     

Analysis of pentasodium triphosphate hydration kinetics

The present work analyzes the effect of various factors on the hydration of pentasodium triphosphate. The experimental method is based on application of the hydration test. Technical-quality products with different proportions of phase I and phase II have been used. The variables studied are phase I/phase II ratio, initial temperature, particle size, stirring rate and composition of the slurry (presence of hexahydrate crystals and water hardness). The results have been discussed according to a kinetics model that includes a series of stages of a physical nature (dissolution of anhydrous salt and the crystallization of the hexahydrate), as well as of a chemical nature (solvation of the ions in solution). Crystallization of the hexahydrate may be the controlling stage in the process.     

Effect of Pt Incorporation into Ni/ZrO2–SO 4 = /Al2O3 Catalyst for n-Butane Isomerization

Three Ni/ZrO₂–SO₄⁼/Al₂O₃ catalysts with different concentrations of platinum (0.2, 0.3 and 0.4 wt%) were prepare and tested for n-butane isomerization reaction at 338 K, in absence and in presence of hydrogen. The results shown that, at low temperature, platinum contributes to the olefin or butyl ion formation and the reaction follows a bimolecular pathway. However, when the reaction occurs in the presence of hydrogen, the formation of butyl ions is inhibited. The main feature of platinum addition is the stabilization of the catalytic activity, which is indicated by the slow deactivation constants compared to that of the unpromoted catalyst.     

In situ observation of methoxide hydrogenation on the Ni(111) surface

The surface chemistry of methoxide (CH₃O-) on the Ni(111) surface has been studied in the presence of hydrogen pressures up to 2 Torr. During heating in vacuum methoxide decomposes to H₂ and CO, which desorb at 380 and 445 K, respectively. The CH₃O-decomposition process is rate limited by CH bond breaking and exhibits a strong deuterium kinetic isotope effect in CD₃O-. In the presence of ambient hydrogen pressures of 0.02–2.0 Torr both CH₃O- and CD₃O-are hydrogenated directly to methanol at 310 K. Methoxide is hydrogenated by adsorbed hydrogen, which nearly saturates the surface at these pressures and temperatures.     

Adhesion Effects of Intermediate Layers on the Densification of Ceramic Powders

In the ceramic technology the first step to produce sintered bodies is the manufacturing of powders which then are densified. The adhesion mechanisms between the single particles and the agglomerates produced from them determine the densification process. Starting from theoretical considerations adhesion mechanisms, such as solid bridge formation, adhesive bonding and glide-promoting effects, are discussed in principle. Subsequently, the effects of surface-active substances on the densification behaviour of clay-ceramics and oxide-ceramic bodies are discussed. Further, the evaluation of the action of additives to the powder mixtures on the microstructure of the compacts, such as porsity and texture, leads to a compaction equation which describes the transition from the powder pile to a densified green body.     

Preparation of Aluminum Nitride Powder from Aluminum Polynuclear Complexes

AIN powder was synthesized from aluminum polynuclear complexes. Basic aluminum chloride and basic aluminum lactate were used as the aluminum polynuclear complexes. These starting materials and glucose were dissolved in water and mixed homogeneously. AIN powder was obtained by calcining after drying and precalcining at 800°C under nitrogen gas flow. Then excess carbon was removed by firing in air. Nitridation in the system was investigated and compared with that in the alumina–carbon black system. It was found that in our reaction system nitridation began and proceeded at lower calcination temperatures above 1200°C than in the alumina–carbon black system. Using aluminum polynuclear complexes, AIN was synthesized through the nitridation of γ-alumina and produced in a very fine and sharp particle size distribution.     

预化学镀石英光纤表面电镀镍层的研究

采用电镀法在石英光纤表面化学镀Ni—P涂层上续镀厚镍,重点考察了硫酸镍质量浓度、十二烷基硫酸钠质量浓度和电流密度对镍沉积速率和镀层质量的影响并确定了其最适宜值。将质量浓度为1．5g·L^-1的稀土氧化镧（La2O3）添加入普通瓦特镀液中考察其对电镀效果的影响。用扫描电镜和体视显微镜对镀层的表面形貌进行了表征和分析。结果表明,添加稀土La2O3细化了金属晶粒和提高了镀层致密程度,镀层样品（厚度约为800μm）具有高硬度、强附着力、低电阻、高密度和良好的可焊性等性能。