Mössbauer effect studies and X-ray diffraction analysis of cobalt ferrite prepared in powder form by thermal decomposition method

Cobalt ferrite (Co_xFe_3?xO₄) is prepared in powder form by thermal decomposition of iron and cobalt salts and is analysed by X-ray diffraction and Mössbauer spectroscopic techniques. The variation of Mössbauer parameters, lattice parameters and crystallite size of the products formed with variation in the composition of Fe and Co ratios are studied. The studies confirm the formation of nano-size cobalt ferrite particles with defect structure and it is found to be maximum for the Fe : Co = 60 : 40 ratio of the initial precursor oxides.     

高频MnZn功率铁氧体烧结工艺研究

按照氧化物陶瓷工艺对高频MnZn功率铁氧体烧结工艺条件进行了研究。烧结温度越高，晶粒越大，晶界越薄，电阻率越低，磁芯损耗越大，起始磁导率和烧结密度分别在1240℃和1230℃达到最大值。延长保温时间，可以使晶粒充分生长，晶界变薄，电阻率减小，损耗增大。保温3h后，起始磁导率和烧结密度均可达到最大值。氧分压越低，材料起始磁导率越高，电阻率越小，损耗越大，但氧分压低于5％后烧结密度不再继续增加。     

片式抗电磁干扰滤波器Ni-Zn铁氧体材料与工艺研究

通过添加适量CuO和Bi2O3，将Ni-Zn铁氧体材料的烧结温度降至870—920℃，达到Ni-Zn铁氧体材料与Ag电极共烧匹配的目的。试制了片式抗电磁干扰滤波器，并对其插入损耗特性进行了计算机模拟，表明所研制的抗电磁干扰滤波器不仅适合高密度表面封装技术的要求，也可满足宽频域抗电磁干扰需要。     

Electromagnetic properties of ferroelectric-ferrite ceramic composites

The NiFe₂O₄ and Pb(Zr_0.52Ti_0.48)O₃ ceramic composites are prepared by conventional solid state reaction method. The microstructural and morphological properties of the composites are studied by X-ray diffraction analysis and scanning electron microscopy. Results indicate that the ferrite and piezoelectric phases can co-exist in the composites. The relationship between the dielectric constant and frequency (40 Hz–40 MHz) as well as temperature is also investigated. It is noted that the transition temperature of the composites is about 380 °C. A double electric hysteresis loop is observed in our composites. The magnetic properties are relatively weak according to the magnetic hysteresis loop. With increase in the content of the ferrite phase, the permeability increases. The electromagnetic properties of the as-prepared composites are tunable according to the content of the NiFe₂O₄ phase.     

锰锌铁氧体纳米粉体的液相制备及磁性能

以δ-FeOOH为前驱体,用氨水调节溶液的pH值,分别采用(1)90℃水浴加热动态转化、(2)沸腾回流动态转化,(3)90℃静态转化及(4)200℃水热法四种方法合成了锰锌铁氧体纳米粉体.采用X射线衍射仪(XRD),透射电子显微镜(TEM)、振动样品磁强计(VSM)和X射线荧光光谱仪(XRF)等方法对粉体进行了表征,对四种液相法制备的锰锌铁氧体纳米粉体的结构和性能等进行了对比和分析.结果表明,四种方法中沸腾回流相转化法得到的产物具有磁性能较好、形状较规则、粒径可控等优点.     

首钢“川气出川”工程用17.5mmX70管线钢的试制

介绍了首钢试制17.5mm规格高强度、高韧性X70管线钢的生产工艺（成分设计、炼钢和轧钢工艺）及产品的力学性能。在华油钢管厂完成制管（管径为1016mm）以及相应的检验后，所有性能指标全部达到“川气出川”管道工程的技术规范要求。     

共沉淀法制备锰锌软磁铁氧体前躯体共沉过程中钙、镁深度脱除的热力学分析

通过对Fe(Ⅱ)-Mn(Ⅱ)-Zn(Ⅱ)-Ca(Ⅱ)-Mg(Ⅱ)-NH3-NH4HCO3-H2O体系的热力学分析，得到各金属离子浓度与pH的关系，从而确定共沉法制备锰锌软磁铁氧体前躯体共沉过程中钙、镁深度脱除的共沉区域。热力学分析结果表明，溶液中钙、镁的含量随着体系pH的增大而降低，在相同条件下镁的溶解度大于钙的溶解度。为减少进入共沉粉中的钙、镁含量，需要保证在铁、锰、锌共沉完全的基础上降低体系的pH。当溶液中[C]T=0．1mol／L，[N]T=1．0mol／L时，pH控制在6．23～6．50之间可以大大降低进入共沉粉中的钙、镁含量。确定共沉过程钙，镁深度脱除的共沉区域，对于生产高纯锰锌软磁铁氧体前躯体具有重要的指导意义。     

Miniaturization and bandwidth enhancement of a cavity backed circular microstrip patch antenna

The resonant frequency of a circular patch antenna with and without circular cavity is measured. The patch miniaturization in the presence of the cavity is proved. Different methods of reducing resonant frequencies and broadening bandwidth without significantly reducing antenna gain are presented. Capacitively loaded patch and slits on the patch stimulate the patch at lower frequencies and multiple resonances, thus help miniaturization. Finally ferrite loading on the feed probe further increases the bandwidth without significantly reducing the antenna gain. The method is much more improved than that for a resistive loaded patch and a deformed patch. © 2007 Wiley Periodicals, Inc. Int J RF and Microwave CAE, 2007.     

ST－4型节能全自动辊道双推板窑

ＳＴ－４型全自动辊道双推板窑是为永磁铁氧体规模生产而研制的一种节能型空气烧结窑。它根据永磁铁氧体烧结的工艺要求，设计了合理的温区，使规模生产烧结成品率达９５％以上；采用辊道推板相结合的窑床形式与复合保温结构，达到了永磁铁氧体能耗１．２ｋｗｈ／ｋｇ；采用优化设计，使设备性能先进，稳定可靠。     

球磨纯铁中纳米铁素体的形成机制

通过形貌观察和硬度测试研究了球磨纯铁中纳米铁素体的形成机制，结果表明，在球磨过程初期，纳米铁素体首先在球磨颗粒的表层区域形成并呈现层片状结构，扫描电镜（SEM），透射电镜（TEM）和高分辨电镜（HREM）观察表明，层片状纳米铁素体区与颗粒内部加工硬化区具有不同的微观结构，而且它们之间的界面十分明显，显微硬度测试试表明，前者的硬度数值明显高于后者，进一步的球磨过程导致颗粒细化并完成转变为纳米铁素体，分析表明，纳米铁素体的形成是由于球磨过程中加工硬化效应产生的位错胞墙结构向晶界结构转变而导致的，这也是造成加工硬化区与纳米铁素体之间存在的硬度差异的原因。