含微量元素铜焊锡丝的研制

在６０／４０的锡铅焊料中加入０．２％左右的铜，凝固后具有均匀细小的共晶组织，其熔点为１８３℃，焊点强度和扩展率均高于未加铜的６０／４０锡铅焊料，并且含铜的锡铅焊料在焊接时，对铜烙铁头和微细铜线了小的熔蚀性。     

压力对Fe－29wt％Ni合金超细微粒特性的影响

利用蒸发冷凝法，制备了不同平均粒径的Ｆｅ－２９ｗｔ％Ｎｉ合金超细微粒。在不同压强下，将超细微粒压制成片。随压强增大，马氏体体积分数和比饱和磁化强度σｓ明显增大，而矫顽力Ｈｃ呈线性下降。压力效应与平均粒径ｄ大小密切相关     

Direct electroless Ni-P deposition on AM50 magnesium alloy from sulfate bath

A bright electroless Ni-P deposition on AM50 magnesium alloy in a sulfate plating bath was proposed by using direct plating process with non-chromate pretreatment. The electroless Ni-P plating on AM50 magnesium alloy has an admirable appearance and good adhesion. The results indicate that the electroless Ni-P deposition with non-chromate pretreatment has better adhesion than that of zinc immersion coating. Anodic polarization curves indicate that the electroless Ni-P deposition obtained from the sulfate bath has similar corrosion-resistance to that obtained from basic nickel carbonate bath. The deposition process generates less pollutant by a non-chromate plating bath and is suitable for the magnesium alloys manufacture because of its low cost. The hardness of the electroless Ni-P plated AM50 is about HV 720.6 and HV 969.7 after heat treatments at 180℃ for 2 h. The wear resistance of Ni-P plated magnesium alloy specimens is about 5 to 9 times as high as that of bare magnesium alloys.     

热强钛合金BT25组织与性能

介绍了前苏联航空发动机用热强钛合金（或高温钛合金）BT25的发展概况，并对BT25合金的成分特点、热处理强化优点等做了进一步阐述，给出了退火状态下的物理性能，在说明热强钛合金微观组织与力学性能关系的基础上给出了BT25合金的各种力学性能。     

等离子喷涂燃料电池连接板LSM薄膜的性能研究

采用等离子喷涂法在SUS 430连接板基体上制备了LSM(La0.8 Sr0.2 MnO3)薄膜。用X射线衍射仪、扫描电镜和电子探针分别研究了喷涂前后LSM的相组成、薄膜的表面形貌和元素分布。用图像分析法计算了薄膜的孔隙率。二支点法测量了有与无LSM薄膜的SUS 430基体在130～800℃时的电导率。结果发现,薄膜与基体结合良好,薄膜孔隙细小,均匀分布,且非连通;LSM的相组成在喷涂前后保持一致;当温度<330℃时,有LSM保护膜的连接板的电导率小于无LSM薄膜的连接板的电导率;温度>330℃,结果相反。有LSM保护膜的连接板在空气中,130～800℃下,最大电导率为0.60Ω-1·cm-1。     

Homogeneous Plastic Flow of Fully Amorphous and Partially Crystallized Zr_(41.2)Ti_(13.8)Cu_(12.5)Ni_(10)Be_(22.5) Bulk Metallic Glass

The homogeneous plastic flow of fully amorphous and partially crystallized Zr(41.2)Ti(13.8)Cu(12.5)Ni(10)Be(22.5) bulk metallic glass (Vitl) has been investigated by compression tests at high temperatures in supercooled liquid region. Experimental results show that at sufficiently low strain rates, the supercooled liquid of the fully amorphous alloy reveals Newtonian flow with a linear relationship between the flow stress and strain rate. As the strain rate is increased, a transition from linear Newtonian to nonlinear flow is detected, which can be explained by the transition state theory. Over the entire strain rate interval investigated, however, only nonlinear flow is present in the partially crystallized alloy, and the flow stress for each strain rate is much higher. It is found that the strain rate-stress relationship for the partially crystaltized alloy at the given temperature of 646 K also obeys the sinh law derived from the transition state theory, similar to that of the initial homogeneous amo     

成形工艺对快速凝固Al—Cu—Mg合金组织和性能的影响

采用自制离心雾化装置制取了快速凝固LY12硬铝合金粉末,研究了以该粉末制成的真空热压件和挤压丝材的组织和性能。结果表明,所得粉末为泪滴状,其显微组织为树枝状晶和胞状晶。真空热压件密度高时所对应的强度高。450℃、10min、150MPa为较合理的工艺,此时粉末颗粒间结合密实,晶粒尺寸没有明显改变。在500℃热挤压时,挤压丝的组织已发生了再结晶,晶粒尺寸仍较细小。挤压丝材的抗拉强度达460MPa,其断口为韧窝状,韧窝尺寸小于3μm,且分布均匀。     

LF6铝合金的超塑性／扩散连接组合工艺试验及理论研究EI

本文研究了ＬＦ６铝合金的超塑性／扩散连接组合工艺，用变形和再结晶的方法细化晶粒，成功地进行了ＳＰＦ／ＤＢ工艺试验，利用电子探针观察了扩散连接接头的界面微观区域，并从机理上分析了金属的超塑性／扩散连接两种工艺之间的内部联系及其金属学行为。     

Relationship between Relaxation Internal Friction Peak at about 200℃(f≈1Hz)and Bainitic Transformation In a CuZnAl Alloy

The present investigation showed that the re-laxation peak at about 200℃ (f≈1Hz) was relatedto bainitic transformation in a CuZnAl alloy.Thepeak decreased when bainite precipitated.Theactivation energy of the peak was the same as theapparent activation energy of bainitic transforma-tion.According to the relations between the peakand the bainitic transformation,the mechanism ofthe peak has been discussed.     

液态挤压在铝合金减震筒上的应用：液态挤压比压值对制件性能影响的分析

指出了压力铸造及热挤压工艺生产铝合金减震筒的缺点，阐述了液态挤压的特征，介绍了液态挤压在减震筒上的应用，分析了比压值对制件性能的影响。