铸造铝合金(ZL109)激光表面处理

采用功率为2kW级CO_2连续可调式横流激光光源,对不同涂层的ZL109试样表面进行了激光熔凝的实验研究。     

The influence of NaCl and CO2 on the atmospheric corrosion of magnesium alloy AZ91

The influence of NaCl and CO₂ on the atmospheric corrosion of magnesium alloy AZ91 is studied in the laboratory. Samples were exposed under carefully controlled air and flow conditions; the relative humidity was 95%, the temperature was 22.0°C and the concentration of CO₂ was < 1 ppm or 350 ppm. Different amounts of sodium chloride (0–70 μg/cm²) were added before exposure. The corrosion products were analyzed by gravimetry, ion chromatography, X‐ray diffraction and scanning electron microscopy. Mass gain and metal loss results are reported. The combination of high humidity and NaCl is very corrosive towards AZ91. However, the NaCl‐induced corrosion is inhibited by ambient concentrations of CO₂. Exposure in the absence of CO₂ gives rise to heavy pitting, with brucite, Mg(OH)₂, being the dominant corrosion product. In the presence of CO₂ a layer of hydrated magnesium hydroxy carbonate, Mg₅(CO₃)₄(OH)₂ · 5 H₂O forms. A tentative corrosion mechanism is presented that explains the behavior in the two environments.     

离子注入对铁及其低合金、铝及其合金耐腐蚀性能的影响

离子注入对金属腐蚀行为的研究已达30年．研究结果表明离子注入对改变金属表面成分和表面性能是极为有效的技术．本文概述了离子注入对铁及其低合金、铝及其合金的腐蚀电化学行为的影响．涉及的注入离子达十余种。     

WC/Ni60真空熔烧涂层的组织结构特性

研究了真空熔烧WC Ni60复合涂层的显微组织结构特性 ,并测定了沿层深方向的显微硬度分布。研究结果表明 ,涂层与母材 4 5钢在界面处形成牢固的冶金结合 ,界面两侧的显微硬度呈连续性分布     

铜铟铋硫对Sn-Ag基无铅焊料性能的影响

研究了Cu、In、Bi、S元素对Sn-Ag基无铅焊料熔点和铺展性的影响。结果表明:Sn-Ag-Cu三元合金成分为95.5%Sn3.5%Ag1%Cu时具有较低熔点(215℃)和好的铺展性;加入适量的In可降低Sn-Ag合金的熔点和改善铺展性能;随w(Bi)的增加Sn-Ag-Bi三元合金的熔点降低、铺展性变好;Sn-Ag合金的熔点随w(S)的增加而升高,加入少量S能改善Sn-Ag合金的铺展性。     

Microstructural changes accompanying repair welding in 5xxx aluminium alloys and their effect on the mechanical properties

At the shipyards, the aluminium alloy 5083 is welded with a multi-pass sequence using the metal inert gas technique. If, while checking the weld integrity either after welding or during service, defects are detected in the vicinity of the weldment, repairs are usually employed to extend the service life.

The repair method involves removal of the upper passes, depending on the thickness and re-welding under the same conditions.

Purpose of this paper is to examine the microstructural changes accompanying repair welding, define their effect on properties of primary importance and set, if possible, an upper limit as far as the number of repairs is concerned.     

Experimental investigation of the normal spectral emissivity and other thermophysical properties of pulse-heated Ni-Ti and Au-Ni alloys into the liquid phase

1. Introduction Metal working industry needs accurate thermo- physical properties of liquid metals and alloys as input data for different simulation routines to im- prove the performance of their products. Within this paper we continue the systematic investigation of the dependence of emissivity of binary alloys on the relative concentration of the constituent elements (for a previous paper see [1]). 2. Experimental method A fast ohmic pulse heating technique is applied to heat metallic wire-s…     

亚硝酸钠作释放剂选择性螯合滴定法测定钯

用EDTA螯合Pd^2 和其它金属离子，然后用亚硝酸钠分解Pd—EDTA螯合物，释放出的ED—TA用Zn^2 标准溶液进行返滴定。大量各种金属离子都不干扰。用于测定Pd—Cu合金镀层、Pd—Sn—Cu合金镀层和Pd—Ti—Si合金中的钯，获得相当满意的结果。     

熔体的粘度，亚稳相，相变和相图——Ⅲ．合金液相相图

对Sn（x）Bi（1-x）11种组分（x=0.10％，20％…80％，90％，100％）的熔体的粘度进行了测量，给出了它们的相变点Tt，相区和相参数；根据这些参数作出了一个二元合金液相相图；为了表明相区的划分和每个相区的结构特征提出两种相图的形式；第1，温度一组分（T-X）图，第2，结构-组分（df-x）图。     

Dental amalgam – the effect of the technology of alloy powder preparation on the corrosion behaviour and the release of mercury

Dental amalgams are based on a broad spectrum of materials differing in their chemical composition, metallurgical treatment, and in the way the initial alloys powders are prepared. In addition to their chemical composition, amalgams based on various powders differ in both their microstructure and the amount of mercury needed for preparation. All these facts may affect electrochemical processes occurring during their interaction with oral fluids, and also mercury release. While verifying the effect of the technology used for the preparation of the high‐copper ternary alloy powder on the properties of resulting amalgams, this study aimed at the mechanism of their interaction with a model saliva solution as well as mercury release was included. Measurements were done in a model saliva solution using standard electrochemical methods and exposition measurements. The interaction of individual types of amalgams with artificial saliva did not reveal any significant differences. The free corrosion potential of all these amalgams in an aerated solution settled in the range of values in which tin oxidation, resulting in a layer of insoluble corrosion producsts, turned out to be the dominant anodic process. The rate of mercury release was the lowest for amalgams based on a gas‐atomized alloy. The highest rate of mercury release, and also its dependence on time, was exhibited by lathe‐cut powder based amalgam. In addition to different volume fraction of the Ag‐Hg phase and the level of its tin alloying, this different behaviour may be explained by differences in the rate at which a layer of tin corrosion products acting as a barrier to mercury release is formed.