首钢2号高炉的技术进步

介绍首钢2号高炉大修采用的新技术、开炉操作和投产以来的生产情况。     

Effects of chemical and plasma surface treatments on the O2-annealed Ni/Au contact to p-Gan

The effects of boiling Aqua Regia (AQ), N₂/Cl₂ plasma followed by AQ and O₂ plasma followed by AQ surface treatments prior to Ni/Au (20 nm/20 nm) metallization to p-GaN:Mg (∼ 3 × 10¹⁷ cm^− 3) have been investigated. N₂/Cl₂ plasma was employed in a bid to lower the Ga/N and O/Ga ratios of the GaN surface to improve the contact properties to p-GaN, while O₂ plasma was employed as an alternative to incorporate O into the Ni/Au system. Results show that a low Ga/N ratio does not necessarily correspond to a better contact. The positive effect of O₂ over N₂ anneal is observed only for the AQ-treated sample, although the mechanisms responsible for its positive effect: NiO formation and Ni/Au layer-reversal were observed for all O₂-annealed contacts. We conclude that the effect of O₂ anneal on the Ni/Au contact is dependant on the p-GaN surface prior to metallization.     

Al2O3对唐钢高炉炉渣性能的影响

针对唐钢近2年提高进口矿配比后，Al2O3含量升高对炉渣流动性带来的不利影响，对唐钢高炉的炉渣性能进行了试验研究。并结合国内同行业的生产实践经验，从理论上分析了炉渣中Al2O3及MgO的适宜含量范围，着重论述了唐钢所处冀东矿区条件下降低Al2O3的主要途径及适应高Al2O3炉渣的具体措施。     

炉顶红外摄像装置在新钢6号高炉上的安装及应用

阐述了高炉炉顶红外摄像装置的安装及应用。该装置对及时了解和掌握高炉炉喉的料面情况、煤气流的分布状况，对指导高炉操作、维护炉况顺行和稳定，改善各项技经指标，发挥了重要作用。     

Thermal and thermoelastic properties of fast extrusion furnace (FEF) carbon black loaded SBR vulcanizates

The effect of FEF carbon black as filler on the thermal capacity c, diffusivity a, and thermal conductivity λ, of styrene butadiene rubber (SBR) composites in the temperature range 300–420 K was studied. The filler strongly increases the thermal diffusivity, whilst strongly decreasing the thermal capacity and the thermal conductivity (except at high FEF content ≥80 phr). The influence of the filler on the thermoelastic behaviour of the same composites was also investigated. It was found that the thermoelastic temperature change (ΔT) increased with carbon black concentration as well as the entropy change per unit extension.     

用发生炉煤气进行快速热风烤窑的应用

用发生炉煤气进行快速热风烤窑的应用王善波，王志军（山东荣成市玻搪工程有限公司２６４３０９）ＰｒｏｄｕｃｅｒＧａｓＵｓｅｄｆｏｒＦａｓｔＨｅａｔｉｎｇｕｐＴａｎｋＦｕｒｎａｃｅ￥ＷａｎｇＳｈａｎｂｏ；ＷａｎｇＺｈｉｊｕｎ（ＳｈａｎｄｏｎｇＲｏｎｇｃｈｅ...     

掺杂WRe3、WRe25合金的高温电阻－温度特性

本文报导了采用一种新型高温陶瓷发热体高温管状炉，通以氩气保护，测量ＷＲｅ合金丝的电阻－温度（１６００℃）特性试验方法，该方法较真空炉简便、实用且试验费用低而准确，测量数据与美国研究报导一致。     

改造加热炉系统 提高加热炉热效率

分析了重整装置加热炉热效率低的原因，介绍了提高加热炉热效率采取的几项措施。     

乙烯裂解炉辐射段流动与燃烧的三维数值模拟

用计算流体力学软件Fluent6.2对中国石油化工股份有限公司燕山分公司E-BA-107乙烯裂解炉辐射段内的流动和燃烧做了三维数值模拟研究。为保证计算的准确性,使用GAMBIT2.2软件建立了与裂解炉实际尺寸完全一致的几何模型;在计算过程中采用了标准k-ε湍流模型、离散坐标辐射模型和有限速率/涡流耗散燃烧反应模型等计算模型。通过模拟计算得到了裂解炉炉膛内的温度、烟气流速及烟气组成的分布:底部燃烧器和侧壁燃烧器的燃烧使附近的炉墙处于温度分布均匀的高温区,为裂解反应提供了均匀的辐射墙面;炉管底部比其他部位的温度低;底部燃烧器的高速射流产生的旋涡可为炉管提供一定的对流热;出口烟气的平均温度和组成的模拟计算值与设计值接近,表明数值模拟有较高的精度,具有实际意义。     

高炉煤气干法除尘技术发展现状及宝钢应用前景

在对高炉煤气干法除尘技术应用现状进行综合分析的基础上结合宝钢实际，提出宝钢应用此技术的相关建议。