BaFe12O19/SiO2-B2O3微晶玻璃陶瓷的制备和微波性能

采用柠檬酸sol-gel工艺合成了BaFe12O19/SiO2-B2O3微晶玻璃陶瓷，研究了SiO2-B2O3玻璃的含量，Ba/Fe原子比和热处理温度对体系析出晶相的影响，以及介电常数和磁异率在1MHz-6GHz频率范围的变化规律，结果表明，休系中SiO2-B2O3玻璃的含量和Ba/Fe比越高，BaF312O19相的析出越困难，前驱体合适的热处理温度为1000℃，介电常数和磁导率基本上随测试频率的增而加下降；介电损耗的最大值为0．43，磁损耗较小。     

Effects of solvent and temperature on the coupling agent/epoxy resin interface

Increased wetting of the coupling agent/epoxy resin interface was observed when γ-glycidoxypropyltrimethoxysilane, polyfunctional aminosilane and γ-aminopropyltriethoxysilane were applied respectively from methyllethylketone, dimethylformamide and water on woven glass cloths which had been cleaned at 300°C. However, when factory-applied coupling agents were burnt off the woven cloths and fresh coupling agents re-applied, it was found that the nature of the factory-applied coupling agent influenced subsequent wetting. Thinner glass fibres showed a greater improvement in wetting rate than thicker fibres in those solvents identified to be good for improved wettability, irrespective of the heat-cleaning temperature.     

Physical Aging of Amorphous Fructose

ABSTRACT: Physical aging of amorphous anhydrous fructose at temperature 5 °C and at 22 °C was studied using differential scanning calorimetry (DSC). The dynamic glass transition temperature, T_g0 for unaged samples was 16 °C and 13.3 °C for heating rate of 10 °C/min and 1 °C/min, respectively. The fictive temperature, T_f0 for unaged samples calculated by Richardson and Savill method was 12 °C, which is close to the dynamic value obtained from the lower DSC heating rate. The fictive temperature T_f of the aged fructose glasses at temperatures both below and above the transition region was fitted well by a non-exponential decay function (Williams-Watts form). Aging above the transition region (22 °C) for 18 d increased both the dynamic glass transition temperature T_g and the fictive temperature T_f. However, aging below the transition region (5 °C) for 1 d increased the dynamic glass transition temperature T_g but decreased the fictive temperature T_f.     

JOINING MECHANISMS OF β''''-Al2O3 CERAMIC AND PYREX GLASS TO Al MATRIX COMPOSITE

The bonding of β'-Al2O3 and pyrex glass to Al matrix composites by anodic bonding process is achieved. The microstructure of the bonded interface and the joining mechanisms are analyzed with scanning electron microscope (SEM), energy dispersive X-ray fluorescence spectrometer (EDX). It is observed that the bonding region across the interface consists of the metal layer, oxide transitional layer and the ceramic layer, with the transitional layer composed of surface region and sub-surface region. The bonding process can mainly be categorized into anodic bonding process and solid state diffusing process. The pile-up of the ions and its drift in the interface area are the main reasons for anode oxidation and joining of the interface. The temperature, voltage and the drift ions in the ceramic or glass during the bonding process are the essential conditions to solid state diffusing and oxide bonding at the interface. The voltages, temperature, pressure as well as the surface state are the main factors that influence the anodic bonding.     

Thermal-lens and photo-acoustic methods for the determination of SiC thermal properties

In this paper we report the use of photothermal techniques such as Thermal lens (TL) spectrometry, Photoacoustic and heat capacity, ρc_p, to determine the thermo-optical parameters, such as thermal conductivity (K), thermal diffusivity (D), specific heat (c_p) and the optical path dependence with temperature (ds/dT), of an undoped polycrystalline 3C-SiC. To our knowledge, this is the first time that Thermal lens technique is used for wide band-gap systems. Results obtained for the polycrystalline sample with TL technique indicates that ds/dT is negative at room temperature. Moreover, the obtained values of thermal diffusivity and thermal conductivity are in good agreement with that found in the literature, indicating that the phototermal techniques can be used to obtain the referred parameters in circumstances where other techniques cannot be used, for example, in harsh environments.     

太钢不锈冷轧工程防腐蚀施工技术

防腐蚀施工工艺掌握的好坏，直接影响到工程投入生产后的使用寿命，为保证工程质量，以太钢不锈冷轧改造工程冷线防腐为例，对其常发生的质量通病进行认真分析，总结出一套行之有效的施工技术。     

点状屏彩色显示管校正透镜优化设计

本文在条状屏彩色显象管校正透镜设计的基础上，提出了蹼状屏彩色显示管校正透镜的优化设计方法并给出了设计实例，通过计算机模拟电子束轨迹和光线追迹，分析了校正透镜面型修正程序的精度。     

用单透镜变换由多模光纤出射的大功率Nd：YAG激光束的特性

根据理论假设，通过选取单透镜的参数和位置，计算说明了单透镜使经由多模光纤出射的大功率Ｎｄ：ＹＡＧ激光束的发射角压缩，光束聚焦效率提高，光束截面场为高斯分布；文中的计算结果符合已知规律，从而说明了理论假设的正确性。     

波导短程透镜球差特性分析及其焦距精确测量方法的研究

本文研究短程透镜的焦点位于端面外的球差特性。对焦点位于波导外部（包括端面）的情况给出了一种精确测量焦距新方法，采用这种方法简单易行，测量精度取决于读数显微镜的读数精度（０．０１ｍｍ）。     

石英玻璃结构调整和二阶非线性光学效应产生机制的理论研究

从非谐振动理论观点出发．考虑到玻璃在外场及加热条件下结构取向调整和弛豫，对外部静电场和加热的温度及加热时间对其信频光产生的影响进行了探讨性理论研究，结果较好地解释了有关实验现象。