Influence of two-step process and of different stoichiometric ratios on morphologies generated in castor oil epoxy resins

Phase separation during polymerization was studied in a model system consisting of a diepoxide based on diglycidyl ether of bisphenol A (DGEBA), variable amounts of ethylenediamine (EDA) and the mass of castor oil (CO) necessary to obtain a mass fraction equal to 0-15 in a final system where the stoichiometric ratio of amine to epoxy equivalents, r, was equal to 1. A two-step polymerization process was performed by curing first a system with r = 0-5, during variable times before phase separation, and then carrying the system to r = 1. Thermodynamic analysis of samples with different r values led to a linear relationship between the Flory-Huggins interaction parameter and r. The concentration (P) and average size (D?) of dispersed-phase particles followed opposite trends, i.e. P increased while D? decreased, when either r was increased or the time of curing in the first step of a two-step process was decreased. This was explained by assuming that the competition between nucleation and growth was determined by the viscosity at the cloud point, η_cp. Low values of η_cp favoured growth over nucleation and led to fewer but larger particles.     

Hierarchical intelligent control with flexible AC transmission systems application

A novel hierarchical intelligent controller configuration is proposed using an artificial neural network as a control-mode classifier in the supervisory level and a set of pre-designed controllers in the lower level. Controller outputs are modified nonlinearly by the classifying signals in a structure resembling one artificial neuron with adaptively changed weights. The lower-level local controllers are implemented using neural networks. An illustrative example of this approach is based on the transient stabilization of a single-machine infinite-bus system studied in Flexible AC Transmission Systems (FACTS) research.     

Optimal task allocation in hypercube multiprocessor ensembles

Criteria are established to determine the optimal policy for allocating a set of uniform tasks onto a multiprocessor hypercube ensemble. It is shown that the optimal policy depends on the ratio of computation to intertask communication required by the distributed program, and that based on this ratio, tasks should be placed either all on one processor or uniformly distributed over the largest possible hypercube.     

网上电子银行系统

本文简要介绍网上电子银行系统的基本结构。重点讲述信息传送服务器 ,并给出该系统的设计例。     

智能电视,电话信息查询系统

本文阐述了在ＷＩＮＤＯＷＳ环境下开发电脑，电视、电话信息查询系统系统的基本思想、硬软件环境和具体实施方法，并介绍了软件流程。     

Air Filtration and Radon Decay Product Mitigation

Air cleaning as a means of mitigating the risks arising from exposure to indoor radon progeny has been evaluated in a single-family house in the north eastem US. using an automated, semi-continuous activity-weighted size distribution measurement system. The measurements included radon concentration, condensation nuclei count, and activity-weighted size distribution of radon decay products. Measurements were made in the house with and without an operating air filtration system and with various particle sources common to normal indoor activities operating. Aerosols were generated by running water in a shower, candle burning, cigarette smoking, vacuuming, opening doors, and cooking. Using a room model, the changes in attachment rates, average attachment diameters, and deposition rates of the unattached fraction with and without the air cleaning system were calculated. In the presence of active aerosol sources, the air filtration unit typically reduced the concentration of particles within the hour following the end of particle generation. After candle burning, cigarette smoking, and vacuuming in the bedroom, the reductions of PAEC by air filtration are about 60% with the air filtration system operating in the bedroom. During cooking in the kitchen, the reductions of PAEC in the bedroom with the air filtration system were about 40%. However, for all cases the dose reductions were smaller than the particle and PAEC reductions. For those particles that were generated within the bedroom, there was a 20% to 50% reduction in dose. In the case of cooking where the door was open and particles infiltrated from the rest of the house, the dose reduction was only 5% on average and appears to be insignificant. Thus, the dose reductions were h e r than the reductions in activity concentration, but there were no cases where the estimated dose actually increased.     

层状催化剂颗粒的优化设计——双组分等温平行反应体系

针对双组分等温平行反应体系,分析讨论了以提高催化剂活性和选择性为目标时催化剂活性组分的最优分布形式(为δ-函数分布),并给出了确定这种反应体系的催化剂的最佳活性层位置的计算方法。结果表明:以提高选择性为目标的最佳活性层位置比以提高活性为目标的要更靠近催化剂核心,实用的最优位置应介于二者之间。最后,本文还研究了反应动力学级数、本性选择性以及内扩散模数(Thiele 模数)等因素对最佳活性层位置的影响。     

Assessing the performance of intumescent coatings using bench‐scaled cone calorimeter and finite difference simulations

A method was developed to assess the heat insulation performance of intumescent coatings. The method consists of temperature measurements using the bench‐scaled experimental set‐up of a cone calorimeter and finite difference simulation to calculate the effective thermal conductivity dependent on time/temperature. This simulation procedure was also adapted to the small scale test furnace, in which the standard time–temperature curve is applied to a larger sample and thus which provides results relevant for approval. Investigations on temperature and calculated effective thermal conduction were performed on intumescent coatings in both experimental set‐ups using various coating thicknesses. The results correspond to each other as well as showing the limits of transferability between both fire tests. It is shown that bench‐scaled cone calorimeter tests are a valuable tool for assessing and predicting the performance of intumescent coatings in larger tests relevant for approval. The correlation fails for processes at surface temperatures above 750°C, which are not reached in the cone calorimeter, but are attained in the small scale furnace set‐up. Copyright © 2006 John Wiley & Sons, Ltd.     

Construction of a control system for disturbance rejection using a dual observer

A well‐known control system which can reduce the adverse effects of disturbances is a disturbance observer. However, in many cases of mechanical systems, system disturbances which do not satisfy the matching condition may be imposed. Therefore, it may be difficult to reduce the adverse effects of the disturbances by the traditional disturbance observer. In this paper, a method of control system synthesis for disturbance rejection using a dual observer is proposed. This method is based on the zeroing induced by the disturbance localization problem. This problem may be solved by dividing the state space into observable subspace and unobservable subspace. As compared with an H_∞ controller based on perfect observation, the usefulness of the proposed control system for disturbance rejection is demonstrated by numerical simulations for a two‐mass spring system. © 2002 Scripta Technica, Electr Eng Jpn, 138(4): 50–60, 2002; DOI 10.1002/eej.1138