Frequency response function of magnetic bearings using high-temperature superconductor

A high-temperature superconductor YBa₂Cu₃O_7-x with strong pinning force has allowed stable magnetic suspension with no control to be developed. Two types of superconducting magnetic bearings (SMB) using YBCO and permanent magnet were assembled. The two types are radial and axial. The dynamic stiffness of each SMB as it was cooled down under a magnetic field by liquid nitrogen was measured both radially and axially. As a result, it was found that the spring constants of these SMBs were almost as large as a practically desirable value; however, their damping coefficients were lower than the practical level. These findings are useful as one of the data bases for development of an optimum SMB design to support the weight of rotors in an axial direction.     

An examination of the effect of composite constituent properties on the notched-strength performance of composite materials

The effect of matrix and fiber properties on the strengths and failure processes of notched, continuous-fiber composite specimens has been investigated. Bearing, open and filled hole tension and compression tests were conducted on AS-4/3501-6, IM-8/3501-6, AS-4/APC-2 and IM-8/APC-2 specimens. Failure characteristics of tested specimens were studied by fractographic techniques. Failure progression was tracked by means of incremental loading, radiography and fractographic inspection.     

高应力水平下滚动轴承疲劳寿命试验研究

通过在三种不同的强化负荷下进行深沟球轴承疲劳寿命试验，并与常规试验一组结果对比。结果表明，适当地加大滚动轴承疲劳寿命试验负荷，可以大大缩短试验时间，而疲劳寿命依然服从Ｗｅｉｂｕｌ分布，且与常规试验结果基本一致，同时疲劳破坏的形式仍是表面下萌生裂纹，然后扩展至表面形成剥落。     

Influence of the surface conditions on permeation in the deuterium–MANET system

The condition of the surfaces is of crucial importance for the deuterium permeation through materials. In this work a study of the surface constants for the adsorption (σk₁) and release (σk₂) of deuterium under different surface conditions on the martensitic steel DIN 1.4914 (MANET) has been carried out. The growth of an oxide surface layer (Cr₂O₃) of about 25–30 nm in a MANET sample, heat treated in an oxidizing environment, compared to the bare MANET that have a ‘natural' oxide of about 5 nm has provoked a reduction of both the permeation rate and the recombination coefficient (about 3 orders of magnitude). In addition, the permeation governing process has changed from diffusion-limited to surface-limited. The measurements of the permeation rate of deuterium were performed by a gas-phase permeation technique over the temperature range 574–746 K and for deuterium driving pressures in the range from 3 to 10⁵ Pa.     

大跨度架空输水钢管的纵向局部加强设计

本文给出了用加强板加大管道截面系数来增加架空输水管道跨越距离的设计方法及其计算过程,并用实例说明了用此种方法加强大跨度管道的有效性和合理性。     

超高吨位灌注桩静载试验中的预应力混凝土反力装置

在复兴大桥超高吨位灌注桩的静载试验,预应力混凝土反力装置替代了传统的钢梁反力系统。这套装置主要包括预应力锚桩、预应力承台与预应力反力梁。试验结果表明,直接获得超高吨位大直径嵌岩桩的极限承载力相当不易,而对这类问题预应力混凝土反力装置是值得考虑的。     

贝氏体钢内水冷穿孔顶头的粘钢及防止措施

从顶头生产工艺控制的角度,分析了贝氏体钢内水冷穿孔顶头产生粘钢的原因、特点和机制,指出掉鼻、缺肉是顶头粘钢的另一种更为严重的失效形式,强化熔炼工艺控制和保证夹杂物总量在A0.5B1C0.5D1级水平,粘钢问题可以得到有效控制。     

加速国内电弧炉工艺技术的发展

提出以紧凑式电炉流程模式对国内电炉钢厂进行改造，以及加强大型电炉冶炼工艺技术研究的建议。     

�±���������͹��ữ���ֳ�ʩ��������Է���

本文介绍了陕北气区陕35井第一次下光油管(即不带封隔器)酸化的施工情况,并结合该地区的地层压力特征分析了光油管酸化施工的可行性及应用限度。     

残余应力对55SiMnVB弹簧钢疲劳性能的影响

研究了５５ＳｉＭｎＶＢ弹簧钢板疲劳断口特征及裂扩展过程。结果表明，喷丸强化在表层产生的残余压应力可明显提高疲劳抗力，增强裂纹闭合效应，降低裂纹扩展速度。