一种新型偶联剂的应用研究

研究了新型偶联剂(XOL-4)用于不同填料的效果。选用滑石粉、CaCO_3、SBS三种不同类型的填料,以不同用量的XOL-4进行表面处理来填充树脂,考察了所得填充体系的拉伸强度、弯曲弹性模量、热变形温度等性能,同时与钛酸酯偶联剂和铝酸酯偶联剂进行了比较。     

A Solder Alloy Filled Z-Axis Conductive Epoxy Adhesive

Epoxy adhesives filled with four different volume fractions of eutectic tin-bismuth solder alloy were prepared and the effect of filler content on the electrical and mechanical properties of these anisotropic electrically conductive adhesives was investigated. The results show that the adhesive containing the lowest amount of the filler alloy had the best combination of conductivity, insulation resistance and shear strength. The DSC-measurements suggested that the filler melts before the cure of the resin begins which allows the filler to wet and bond well to the conductors. This was verified by SEM/EPMA examinations. A temperature cycling test and high humidity, high temperature treatment were conducted on the best composite adhesive. The temperature variation had no effect on conductivity of the joints while humid and hot environment decreased the conductivity.     

利用废旧高分子材料制备改性石油沥青

利用废旧高分子材料、无机填料为改性剂，采用熔融共混方法制备了一系列性能优异的新型改性石油沥青，分析了改性剂类型和用量对石油改性沥青的软化点、脆化温度、针入度和延度等性能的影响。结果表明：改性石油沥青的针入度和延度稍有降低，但其软化点明显升高，脆化温度降低，拓宽了石油沥青的使用温度范围，综合性能提高。     

从煤矸石制取氯化铝联产橡胶填料的研究

在实验室小试、中试装置上进行了从煤矸石制取氯化铝联产橡胶填料的研究，考察了煤矸石性质、工艺条件等对产品质量的影响，结果发现最佳工艺参数为焙烧温度６００～ｑ００℃．焙烧时间为１５～９０ｍｉｎ．焙烧温度对产品质量影响更为显著，制得结晶氯化铝产品质量达到合格品标准，填料用作橡胶制品填充剂具有较好补强与抗曲性能，其胶片的物理机械性能达到普通橡胶板标准。     

Resistivity and thermal reproducibility of carbon black and metallic powder filled silicone rubber heaters

Flexible heaters were prepared by extruding platinum‐catalyzed silicone rubber composites with conductive carbon black (CB) and metallic fillers. The conductor resistivity of the extruded heaters decreased in order of conductive titanium dioxide (TiO₂) > aluminum powder ≈ zinc powder > copper powder. Thermoelectric switching phenomena were investigated for the silicone rubber/CB/metallic powder systems. The positive temperature coefficient effect was dependent mainly on the CB content rather than on the content of the metallic powders. Resistivity and thermal reproducibility of the extruded heaters were also investigated by periodically applying AC voltage of 110 V. The heaters containing copper and TiO₂ powders exhibited excellent electrical reproducibility. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 95: 1122–1128, 2005     

Influence of Fillers on Sizing Efficiency and Hydrolysis of Alkyl Ketene Dimer

The influence of various fillers on sizing efficiency, adsorption and hydrolysis of alkyl ketene dimer (AKD) has been investigated. Results indicated that the precipitated calcium carbonate (PCC) improved AKD retention, both bound and unbound. The sizing efficiency was reduced as PCC contents increased, which might be attributed to the decrease in the relative AKD dosage to fibres and AKD hydrolysis promoted by PCC. Less amount of AKD was adsorbed on PCC, compared with calcined clay and TiO₂ fillers under the same conditions. Hydrolysis studies indicated that PCC had a more detrimental effect on AKD hydrolysis than clay and TiO₂.     

Effect of the use of mineral filler on the properties of concrete

Engineers of the concrete technology are increasingly concerned with the material passing through a sieve of the size under 0.149 mm. Materials called very fine aggregate or mineral filler may affect the performance of concrete in an either positive or a negative way. Discussions on aggregate containing very fine material are vitally important. Washing the aggregate residue has been the sole way to solve this matter to date. This is mainly based on the debatable opinion that materials of this kind are regarded as clay material. The goal of the study was to determine how the content of mineral filler might affect properties of concrete. Two types of aggregates with different amounts of cement and mineral filler were used. Basically, mineral filler replaced sand. The effect of applying different amounts of mineral filler on concrete was then determined. The addition of 7-10% of mineral filler to fine aggregate (0-2 mm) was found to considerably improve the properties of concrete.     

填料对反-1,4-聚异戊二烯性能的影响

研究了填料对反－1，4－聚异戊二烯（TPI）硫化胶和混炼胶的物理机械性能和结晶性能的影响。结果表明，在TPI中加入填料后，其硫化胶的300％定伸应力随填料用量的增加而增加，拉伸强度则在填料用量为20份时达到最大值；加入填料同时能降低TPI混炼胶的结晶度，填料用量增加，TPI混炼胶的结晶下降；且填料增强效果越好，结晶度下降越大。     

Investigation of allyl‐capped carbosilane dendrimers used as crosslinker for silicone rubber

High‐temperature vulcanized silicone rubber was prepared by using allyl‐capped carbosilane dendrimers, in which the core molecules were Si(CH₂CH?CH₂)₄ and Ph₂Si(CH₂CH?CH₂)₂ as crosslinker and nanoscale reinforcing filler, respectively. Allyl‐capped carbosilane dendrimers improved the mechanical properties of silicone rubber. The optimum tensile strength and tear strength were 9.6 MPa and 31.0 kN/m, respectively, when using SiG_n(allyl)m as the crosslinker and 10.1 MPa and 32.0 kN/m, respectively, when using Ph₂SiG_n(allyl)m as the crosslinker. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 1772–1775, 2006     

CacO3在PP和PP/mPE共混物基体中的作用比较

研究CaCO3填料在取丙烯（PP）和茂金属聚乙烯（mPE)弹性体增韧PP共混物（PP／mPE)2种基体中的不同作用。结果表明：在PP基体中，填料显著提高其刚性，而在共混物基体中，由于弹性体的存在，填料的增强作用减弱；弹性体能够改善填料粒子和基体的界面粘合，增大弹性体分散相的尺寸，使PP/mPE共混物的拉伸断裂韧性提高。低温下（－30℃）的Charpy缺口冲击实验表明：少量的CaCO3即可导致PP/mPE体系冲击强度的迅速下降。