铸造湿型小件缺陷产生的原因与控制

通过对铸造湿型小件产品缺陷典型实例的原因分析，从型砂的选择及配制、造型工艺、浇注工艺等方面提出控制缺陷产生的工艺方法。     

Estimating thermal stress in BIPV modules

The thermal stress on building‐integrated photovoltaic modules (BIPV) in Espoo, Finland, was studied with field‐testing of amorphous silicon modules. Based on these results, the thermal stress at two other European locations (Paris and Lisbon) was estimated. The estimation procedure entailed thermal modelling of heat transfer in the façade with meteorological data as input. The results indicate that the thermal stress on BIPV modules in Lisbon is, in this case, approximately 50% higher that in Espoo and between 80 and 200% higher than in Paris, depending on the activation energy of the degradation process. The difference in stress between a BIPV module and a free‐standing module in Espoo was 50–200%. Copyright © 2006 John Wiley & Sons, Ltd.     

液态金属钠高温沸腾实验回路应力分析与强度计算

本文主要完成了液态金属钠高温沸腾实验回路的应力分析与计算，确定了回路高温区连接管系的布置型式和支吊架系统，是该回路总体设计的重要组成部分。     

Adaptive control in a heating vessel: A comparative study

This paper presents experimental results obtained in temperature adaptive control of a heating vessel. A non-linear model of the process showed that the feed flow rate causes severe variations in time constant and process gain. An extended horizon self-tuning controller and two different model reference adaptive controllers were tested. The influence of design parameters on control performance for each algorithm was assessed. The control system was disturbed with load and setpoint changes.     

Development of temperature compensated high elongation resistance strain gauges for use up to 250°C

The paper describes the development and evaluation of temperature compensated high elongation resistance strain gauges for use from room temperature to 250°C. These gauges could be temperature-compensated on steels with coefficient of thermal expansion α = 11 ppm/°C. Thermal output within 250°C was about 1 μm/m/°C and maximum standard deviation of 5 gauges was 34 μm/m. Strain limit was > 4% at room temperature and at 250°C. Gauge factors of different strain ranges at R.T. and at 250°C are tabulated. Some applications are stated.     

Series resonant ZCS‐PFM DC‐DC power converter with high‐frequency high‐voltage transformer link for high‐power magnetron drive

This paper presents a single lossless inductive snubber‐assisted ZCS‐PFM series resonant DC‐DC power converter with a high‐frequency high‐voltage transformer link for industrial‐use high‐power magnetron drive. The current flowing through the active power switches rises gradually at a turned‐on transient state with the aid of a single lossless snubber inductor, and ZCS turn‐on commutation based on overlapping current can be achieved via the wide range pulse frequency modulation control scheme. The high‐frequency high‐voltage transformer primary side resonant current always becomes continuous operation mode, by electromagnetic loose coupling design of the high‐frequency high‐voltage transformer and the magnetizing inductance of the high‐frequency high‐voltage transformer. As a result, this high‐voltage power converter circuit for the magnetron can achieve a complete zero current soft switching under the condition of broad width gate voltage signals. Furthermore, this high‐voltage DC‐DC power converter circuit can regulate the output power from zero to full over audible frequency range via the two resonant frequency circuit design. Its operating performances are evaluated and discussed on the basis of the power loss analysis simulation and the experimental results from a practical point of view. © 2005 Wiley Periodicals, Inc. Electr Eng Jpn, 153(3): 79–87, 2005; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20126     

强流质子直线加速器中束晕现象研究

从束流包络方程与单粒子运动方程联立模型出发，考虑了纵向能量方程的耦合，研究了强流质子直线加速器中的束晕现象。采用相交间的Ｐｏｉｎｃａｒｅ截面方法和实空间Ｐｏｉｎｃａｒｅ截面方法，研究了周期聚焦系统失配的情况下束晕的形成以及加速对束晕形成的影响。     

浅议轨道交通直流牵引供电系统的构成及保护配置

介绍了城市轨道交通直流牵引供电系统的构成,详细叙述了直流牵引供电系统的主要电气设备及其连接方法,以及系统的运行方式.另外,还简单介绍了系统配置的直流保护以及保护原理和保护作用.     

利用热管纺丝技术一步法生产FCY

利用平板型热管纺丝装置对普通高速纺丝机进行技术改造，并一步法生产出充分结晶的ＰＥＴ纤维（ＦＣＹ）。该纤维可直接用于织造，调节热管温度、热管安装位置可获得满足后道工序不同需要的ＦＣＹ。