Surface finish generated in hard turning of quenched alloy steel parts using conventional and wiper ceramic inserts

Significant progress has already been achieved in green manufacturing including dry and hard, often high-speed, machining technologies. For instance, the demand for higher productivity has resulted in the wider application of ceramic and PCBN tools with special multi-radii (wiper) geometry. This paper reports some important characteristics of the surface roughness produced in the turning of a hardened low-chromium alloy steel using mixed alumina–titanium carbon (TiC) ceramic cutting tools equipped with both conventional and wiper inserts. The characteristic geometrical features of surfaces obtained in both these turning operations have been assessed by means of representative two-dimensional (2D) surface roughness parameters, and some 3D visualizations, which allowed more complete characterization of the surface topography and prediction of its service properties. Results show that keeping equivalent feed rates, i.e. 0.1 mm/rev for conventional and 0.2 mm/rev for wiper tools, the surfaces obtained have similar 3D height roughness parameters, and comparable values of skew and kurtosis. At defined cutting parameters, surfaces produced by wiper tools contain blunt peaks with distinctly smaller slopes resulting in better bearing properties. Only marginal changes of Ra parameter were recorded during 15 min machining trials.     

Structures of ceramics coatings on steel fabricated by hot-dipping and micro-arc oxidation

Firstly, an aluminum coating was produced metallurgically on mild steel by hot-dipping, then an aluminum oxide coating was formed self-growingly from the aluminum coating by micro-arc oxidation treatment. The structures of the composite coatings were investigated by means of SEM, TEM and XRD. The results show that the composite coating consists of three layers which are Fe-Al alloy, aluminum coating and aluminum oxide orderly outward from the steel substrate. There are amorphous phases, k-Al2O3 and θ-Al2O3 mainly in the aluminum oxide.     

Effect of surface free energy of ceramic glaze on oil droplet shape and its behavior in water

A super-hydrophilic functional ceramic was prepared by adjusting the chemical components of ceramic glaze. Effect of surface flee energy of ceramic glaze on oil droplet shape and its behavior in water were studied. The results show that water can spread on ceramic surface with high surface free energy, and oil droplet can aggregate rapidly and separate from the ceramic surface in water. For the ceramic with lower surface free energy, the polar shares are dependant on its easy-cleaning property. The higher the polar shares, the better the easy-cleaning property, and the easier the droplet separates from the ceramic surface in water.     

后氧化处理对等离子喷涂陶瓷涂层性能的影响

用正交实验法研究了后氧化处理温度、时间对大气等离子喷涂(Al/Ni+Cr2O3)陶瓷涂层性能的影响,由此获得的优化工艺参数为500℃×4h.研究表明,温度是影响后氧化效果的主要因素,优化的后氧化处理能明显改善涂层性能气孔率减少,致密性改善,硬度提高7.4HR15N,结合强度提高20.39MPa.     

Probability of precision micro-machining of insulating Si3N4 ceramics by EDM

Electrical discharge machining (EDM) is used as a precision machining method for the electrically conductive hard materials with a soft electrode material. But recently we succeeded to machine on insulating material by EDM. The technology is named as an assisting electrode method. The EDMed surface is covered with the electrical conductive layer during discharge. The layer holds the electrical conductivity during discharge. For micro-EDM, the wear of tool electrode becomes lager ratio than the normal machining. So the micro-machining is extremely difficult to get the precision sample.

In this paper to obtain a fine and precise ceramics sample, some trials were carried out considering the EDM conditions, tool electrodes material and assisting electrode materials. Insulating Si₃N₄ ceramics were used for workpiece. The machining properties were estimated by the removal rate and tool wear ratio. To confirm the change of micro-machining process, the discharge waveforms were observed. The micro-machining of the Ø0.05 mm hole could be machined with the commercial sinking electrical discharge machine.     

Effects of gold plating on the resistance to high temperature discoloration of the cavity for ceramic packages

The effects of thickness and types of gold plating on the resistance to high temperature discoloration of gold plating on cavity surface of ceramic package were investigated. It was found that the thicker gold plating, the less discoloration degree for ceramic packages. Non-cyanide gold plating performed better resistance to high-temperature aging than cyanide gold plating. The relationship between the gold plating thickness and the amount of diffused Ni to the gold plating of ceramic packages with Au/Ni and Au/Ni-Co platings after heating at 420℃for 15 min was also studied. When the gold plating thickness reach 2.0 μm and 1.6 μm for Au/Ni and Au/Ni-Co plating systems, respectively, no discoloration was observed on the gold plating surface of cavity, and the corresponding diffused Ni amounts (mass fraction) are 1.0% and 0.4%, while the diffused Co to the gold plating is 0.04%.     

口腔修复用Y-TZP陶瓷材料制备工艺研究

采用国产3Y-TZP亚微米粉体，通过双向模压结合等静压成形有效克服了条形试样的烧结弯曲，探讨了24h排胶工艺对预烧试样力学性能的影响，通过对预烧试样热膨胀曲线的测定、不同烧结温度试样力学性能和密度的比较及XRD定量分析确定了适宜的烧结工艺。结果表明，牙科支架用陶瓷，将预烧试样升至1550℃保温0．5h，排胶工艺对预烧试样的抗弯强度和断裂韧性并无显著影响，对于即可获得足够的抗弯强度，提高其断裂韧性。     

精密铸造硅溶胶模壳的制造工艺

介绍用石蜡-硬脂酸低温模料，生产铸件的熔模和用精密铸造硅溶胶，作为制壳粘结刑，制造铸件的模壳的工艺要求。主要研究熔模制造工艺、硅溶胶模壳工艺和焙烧工艺。五年多来的生产实践充分证明精密铸造硅溶胶模壳制造工艺是成熟的。为生产合格模壳和精密铸件提供了技术保障。     

Bonding of Al2O3 ceramic and Nb using transient liquid phase brazing

The brazing of Al2O3 to Nb was achieved by the method of transient liquid phase (TLP) bonding. Ti foil and Ni-5V alloy foil were used as interlayers for the bonding. The base materials were brazed at 1423-1573 K for 1-120 min. The results show that the shear strength of the joint first increases and then decreases with increasing holding time and brazing temperature. The joint interface microstructure and elements distribution were investigated. It can be concluded that a composite structure, in which the base metals are solid solution Nb(V) and Nb(Ti) reinforced by Ni3Ti, is formed when the brazing temperature is 1473 K and holding time 15 min, and a satisfactory joint strength can be achieved. The interaction of Ti foil and Ni-5V foil leads to the formation of liquid eutectic phase with low melting point, at the same time the combination of Ti come from the interlayer with O atoms from Al2O3 results in the bonding of Al2O3 and Nb.     

扩散处理对Si3N4陶瓷与金属钎焊接头的强化作用

用扫描电子显微镜、能谱仪及X射线衍射仪分析和讨论了复合电镀Ni-Ti陶瓷与金属钎焊接头的强度、微观结构和其界面结合机制。试验表明：扩散处理对陶瓷与金属钎焊接头有强化作用。经辉光扩散处理后，Ti向陶瓷界面扩散，Ni-Ti层与陶瓷发生界面反应。