化学气相沉积法制备碳化铬薄膜的研究

以三（2,2,6,6-四甲基-3,5-庚二酮）化铬为前驱体,采用化学气相沉积（CVD）法在氧化铝（Al₂O₃）陶瓷基板上制备碳化铬（Cr₃C₂）薄膜,其中沉积温度为723 K至923 K,沉积时间为1 200 s。研究了不同沉积温度对Cr₃C₂薄膜的相组成、择优取向、宏观表面、微观结构及电学性能的影响。结果表明,在723 K至923 K下制备得到具有高度（130）择优取向的Cr₃C₂薄膜。随着沉积温度的升高,Cr₃C₂薄膜表面先由光滑变粗糙,后逐渐变光滑;薄膜晶粒呈椭球型生长;薄膜的厚度先增加后减小,从而导致电阻先减小后增大。在798 K时制备得到厚度最大且电阻最小的（130）择优取向的最佳Cr₃C₂薄膜。同时,在实验条件下Cr₃C₂薄膜表面存在少量的碳和Cr₂O₃。     

腐解稻草DOM提取液洗脱六价铬污染土壤试验研究

工矿企业产生的铬渣、含铬废水由于管理不善导致土壤铬污染严重,迫切需要寻求低成本铬污染土壤修复技术。提出腐解稻草中溶解性有机质（Dissolved Organic Matter, DOM）提取液洗脱铬污染土壤的技术,通过实验室模拟试验,以2种铬污染土壤（总铬含量为分别为121.54、941.90 mg/kg,六价铬含量分别为119.90、856.90 mg/kg）为研究目标,采用振荡淋洗法考察了固液比、淋洗时间、淋洗次数等因素对土壤中总铬、六价铬洗脱效果的影响,并探讨了淋洗前后铬形态变化及淋洗后土壤残留六价铬的持续钝化能力。研究结果表明：稻草经35 d腐解后的DOM提取液洗脱土壤中铬效果最佳,确定为最佳淋洗剂;固液比1：15、淋洗4h/次、淋洗2次为最佳淋洗工艺条件,该条件下,2种铬污染土壤总铬分别洗脱了47.79%、85.92%,六价铬含量分别削减了51.76%、95.09%;DOM提取液呈弱碱性,包含大量羧基、羟基及酚类物质,对水溶态、弱酸提取态和残渣态铬有较好的洗脱效果,有效降低了土壤环境风险,且能持续钝化淋洗后土壤中残余的六价铬。     

Effect of SiC nanowhisker addition on microstructure and mechanical properties of regenerated cemented carbides by low-pressure sintering

The hardness and toughness of regenerated cemented carbides, in general, are contradictory. Therefore, it is critical to explore regenerated cemented carbides with both high hardness and high toughness. In this study, regenerated WC-8-wt% Co cemented carbide with SiC nanowhisker were prepared by low-pressure sintering. The influence of SiCw contents on the microstructure and mechanical properties of regenerated WC-8-wt% Co cemented carbide was investigated. The results indicated that the hardness, density, flexural strength, and fracture toughness of regenerated cemented carbide first increased and then decreased with the addition of SiCw. The Vickers hardness, density, flexural strength, and fracture toughness could reach 1575 HV, 14.6 g/cm³, 2204 MPa, 16.85 MPa·m^1/2, respectively, with SiCw content 0.5 wt%, which were increased by 14.4%, 0.7%, 12.2%, and 17.3%, respectively, when compared with the regenerated cemented carbide without SiCw. The lowest friction coefficient and the best wear resistance could be also reached when 0.5-wt% SiCw was added. The fracture mechanism of the regenerated cemented carbide contained both transgranular and intergranular fracture through the microscopic observation of fracture surface via scanning electron microscope.     

Ni/W比对NiWCx催化剂加氢性能的影响

过渡金属碳化物具有类似贵金属的电子结构和加氢性能。采用等体积浸渍法制备了不同Ni/W比的NiW/γ-Al₂O₃催化剂,以程序升温碳化法转化为NiW碳化物后对芳烃模型化合物和低温煤焦油中分离所得芳烃组分进行加氢处理。催化剂的N₂吸附、XRD、H₂-TPR和SEM表征表明,Ni的添加促进了载体表面WO₃物种的分散和还原,抑制了WO₃晶体的团聚和大晶粒的生成。萘的加氢实验表明,Ni/W原子比为0.6时催化剂的活性最佳,而添加苯酚和吡啶后的模型油加氢过程中萘的转化率和十氢萘的产率均明显下降,Ni/W原子比为0.47和0.6的催化剂性能相近,煤焦油中芳烃组分加氢后Ni/W原子比为0.47的催化剂性能更优。结果表明,Ni和W均具有良好的加氢活性,但Ni耐杂原子性能较差,二者存在一个最佳的配比以使加氢性能更优。有杂原子化合物存在时,如煤基芳烃组分的加氢,Ni/W原子比为0.47的NiW碳化物催化剂具有更好的加氢性能。     

Influence of pre-oxidation on the hot corrosion of Ti3SiC2 in the mixture of Na2SO4-NaCl melts

Polycrystalline Ti₃SiC₂ suffered from serious hot corrosion attack in the mixture of 75wt.%Na₂SO₄ + 25wt.%NaCl melts at 850 °C. In order to improve the hot corrosion resistance of this material, pre-oxidation treatment was conducted at 1200 °C in air for 2 h. A duplex oxide scale with an outer layer of TiO₂ and an inner layer of a mixture of TiO₂ and SiO₂ was formed during the pre-oxidation. Because the outer oxide layer of the pre-oxidation treated specimens could inhibit hot corrosion process, they exhibited good hot corrosion resistance in the mixture of 75wt.%Na₂SO₄ + 25wt.%NaCl melts at 850 °C for 50 h. However, during the hot corrosion the outer layer of TiO₂ would degrade gradually. Once the outer layer damaged, the hot corrosion rate increased sharply, the corrosion behavior was similar to Ti₃SiC₂ corroded under the same conditions. The microstructure and phase compositions of the hot corrosion samples were investigated by SEM/EDS and XRD.     

不锈轴承钢真空制备过程洁净度及碳化物变化

 为了提高G102Cr18Mo高碳不锈轴承钢的洁净度、细化碳化物组织,采用真空感应熔炼、两次真空自耗重熔、大锻压比锻造的工艺路线,研究了真空处理及大锻压比锻造对化学成分、气体含量、夹杂物分布、二次枝晶间距及碳化物颗粒度的影响。研究结果表明,真空感应熔炼过程(VIM)中,随着铝含量的增加,碳的脱氧能力大幅降低,即使铝质量分数为0.003%也对碳的脱氧能力有明显的阻碍作用;真空自耗重熔过程(VAR)由于高的真空度、高的重熔温度等热力学条件以及反应动力学条件的改善,氧含量显著降低,第一次自耗重熔后氧质量分数从0.001 49%降低至0.000 57%,降低了61.7%,第二次自耗重熔后氧质量分数降低至0.000 50%。真空感应熔炼、真空自耗重熔过程,夹杂物的成分变化不大,主要以Al-Si夹杂为主,其次为Al₂O₃夹杂,再次为MnS夹杂、Mg-Al-Ca、Mg/Ca-Al夹杂。双真空冶炼后,钢中夹杂物主要为0～5 μm的细小夹杂物,未发现大于20 μm的夹杂,含有少量10～20 μm的夹杂,钢的洁净度大幅度提高。在真空自耗锭横断面上,从边部向芯部二次枝晶的形貌变化不大,二次枝晶间距逐渐增大,但是变化趋势缓慢,二次枝晶间距为85～95 μm,这主要得益于低的自耗重熔速度。对真空自耗锭进行大变形处理,最终锻造成40 mm的圆棒,碳化物颗粒的最大尺寸不大于20 μm,平均尺寸为15 μm,且没有碳化物聚集的现象。低的自耗重熔速度和大锻压比锻造是碳化物细化的关键。     

Formation of a chromium-carbide conversion coating on silicon carbide

The formation of a chromium-carbide conversion coating on SiC was achieved using the pack-cementation technique. The conversion coating is intended to improve the corrosion resistance of SiC and its derivatives, such as SiC-base continuous fibers and composites, by forming a protective Cr₂O₃ scale upon exposure to high-temperature corrosive environments. Different pack chemistry and processing parameters were evaluated in the laboratory. Results indicated that the coating morphologies and compositions achieved were significantly affected by variation of these processing factors. In this paper, the conversion coating obtained from one of the systems investigated is reported. The coating consists of a multilayered structure with each of the sublayers containing a high-Cr concentration. In addition, the coating surface is relatively dense and pore free compared to the underlying SiC substrate material. A dense and pore-free morphology is highly desirable for coating applications, especially on porous substrates. The multilayered coating structure consists of the following sublayers: Cr₂₃C₆/Cr₇C₃/Cr₇C₃+Cr₃Si/Cr₅Si₃C_x/SiC substrate.     

Use of electron microscopy on microstructure characterization of high chromium cast irons

The physical metallurgy underlying the development of cast microstructures in abrasion resistant high chromium cast irons, and their structural modification by thermal treatments is relatively complex. Structural characterisation via electron microscopy therefore has a key role to play in furthering our understanding of the phase transformations that control the microstructures and hence the service performances of these irons as wear parts. This paper shows how both scanning and especially transmission electron microscopy can provide valuable information on the nature of eutectic and secondary carbides and on the matrix structures in these irons. Particular attention is given to current characterisation research on conventionally cast 30%Cr irons that are used for applications involving corrosive wear e.g. slurry pumps and on a semi-solid cast 27%Cr iron that has a potential for applications in industry.     

熔渣法碳化铬涂层的抗氧化性能研究

对熔渣法碳化铬涂层在各种温度下经20h和200h的氧化性能进行了研究，与常用的一些锅炉用钢进行了对比试验，结果表明碳化铬涂层抗氧化性能比15CrMo、102、T91钢好，可以与TP347钢相媲美。     

单晶高温合金定向凝固过程中初生碳化物的上浮现象SCIEI

本文在一种抗热腐蚀单晶镍基高温合金平面及胞状液-固界面定向凝固条件下,发现了初生碳化物(TiC)的上浮现象并分析了其形成原因。