催化裂化装置结焦问题的探讨

针对中国石化股份公司所属56套催化裂化装置近两年半以来由于结焦造成非计划停工的原因，进行分析、探讨并提出了解决办法。指出催化裂化装置的结焦虽然是不可避免的、但通过采取有效措施，可以把结焦对装置安全生产的危害降低到最小程度。     

两栖装甲装备新型防腐材料的研究

沿海地区特殊海洋环境造成装甲装备的严重腐蚀,为了研制一种新型的耐蚀有机涂层,该文作者研究了有机硅改性环氧树脂的化学反应,并对改性树脂的性能进行了测试分析.结果表明,改性树脂克服了环氧树脂的耐温性差、亲水性强以及盐水渗透率高的性能缺陷,为进一步制备该地区装甲装备防腐涂料奠定基础.     

Ideally selective diisocyanate building blocks: New perspectives for dendrimers and coating binders

Using zirconium (IV) salts as catalyst, the reaction of a diisocyanate carrying one tertiary and one primary isocyanate group (IMCI, DIMP) with alcohols can be conducted with complete regioselectivity. This unique selectivity enables the use of a diisocyanate building block in unprecedented ways. Incomplete regioselectivity of diisocyanates, as commonly encountered in currently commercial ones like IPDI and TDI, inevitably leads to polydisperse products in reaction with polyols. The ultimate monodisperse polymer architecture, dendrimers, can now be made in a facile, straightforward manner using IMCI as the ideal diisocyanate building block. Coating applications of this unique building block are not restricted to these perfect branching polymers, but also include isocyanate-functional coating resins. Without any increase in polydispersity, a hydroxyl-functional polyester can be end-capped with the IMCI diisocyanate and subsequently serve as a crosslinker in powder coatings.     

In situ polymerization and characterization of polyester‐based polyurethane/nano‐silica composites

Polyester‐based polyurethane/nano‐silica composites were obtained via in situ polymerization and investigated by Fourier‐transform infrared spectroscopy (FTIR), or FTIR coupled with attenuated total reflectance (FTIR‐ATR), Transmission electron microscopy (TEM), atomic force microscopy (AFM), an Instron testing machine, dynamic mechanical analysis (DMA) and ultraviolet‐visible spectrophotometry (UV‐vis). FTIR analysis showed that in situ polymerization provoked some chemical reactions between polyester molecules and nano‐silica particles. FTIR‐ATR, TEM and AFM analyses showed that both surface and interface contained nano‐silica particles. Instron testing and DMA data showed that introducing nano‐silica particles into polyurethane enhanced the hardness, glass temperature and adhesion strength of polyurethane to the substrate, but also increased the resin viscosity. UV‐vis spectrophotometry showed that nano‐silica obtained by the fumed method did not shield UV radiation in polyurethane films. Copyright © 2003 Society of Chemical Industry     

Surface structural change of ZnO-coated LiNi0.5Mn1.5O4 spinel as 5 V cathode materials at elevated temperatures

LiNi_0.5Mn_1.5O₄ powder was synthesized via sol-gel method and coated with ZnO in order to test the electrochemical cyclability of the material as a cathode for the secondary Li battery in the 5 V range at 55 °C. The ZnO-coated LiNi_0.5Mn_1.5O₄ powder nearly maintained its initial capacity of 137 mA h g⁻¹ after 50 cycles whereas the uncoated powder was able to retain no more than 10% of the initial capacity after 30 cycles. TEM analysis of the cycled cathodes suggests that the formation of the graphitic surface phase, hindering the Li migration, may be responsible for the rapid capacity loss of the uncoated material while no such phase was observed on the surface of the ZnO coated LiNi_0.5Mn_1.5O₄ powder.     

聚酰胺的改性与加工应用

本文介绍了有关尼龙树脂材料改性，共聚和新品种尼龙等聚合物设计技术，聚合物合金等复合技术，以DSI等胶粘技术为中心的相关加工技术的动向和具体事例。     

聚氨酯干法涂层的应用

介绍了涂层织物的特点及聚氨酯在涂层整理中的作用,并对干法直接涂层工艺进行了探讨.     

烷基烷氧基硅烷的合成方法及其在涂料中的应用

介绍了烷基烷氧基硅烷的合成方法(包括烷基的引入方法和烷氧基的形成方法)、近几年来在涂料中的应用及其结构与性能的关系。     

涂层材料的断裂分析(英文)

和基体厚度相比,涂层很薄,因此细观力学模型可把基体作为半无限弹性体。由于涂层和基体材料的膨胀系数及弹性系数不匹配,涂层材料中残余热应力的解析解为 E_c/(1-γ_c)·(α_s-α_c)△T。用有限元法校核,该应力和解析解吻合得好。通过对涂层产生裂纹驱动力和断裂韧性的讨论,提出了抗裂涂层厚度公式。     

化学镀SiCp／Ni－P复合镀层与基体结合强度及其影响因素

论述了ＳｉＣｐ／Ｎｉ－Ｐ复合镀层与钢基体的结合强度及其影响因素。复合镀层中离界面５μｍ厚度以内区域的组成及应力状态对镀层／基体的界面结合有决定性作用，在该区域以外ＳｉＣ粒径变化不影响镀层的结合强度。适当的热处理可提高界面结合力。