唐山建龙900mm冷轧机组的工艺与设备

较系统地介绍了我国第1条国产化的中宽带钢冷连轧生产线，即唐山建龙钢铁控股有限公司900mm冷连轧生产线的工艺流程、主要设备组成及技术特点。重点介绍了900mm 4机架六辊轧机的技术参数、性能特点及自动控制系统。该生产线投产以来，取得了较好效果。     

Analysis of trace mercury in water by solid phase extraction using dithizone modified nanometer titanium dioxide and cold vapor atomic absorption spectrometry

A new method for analysis of trace mercury in water samples was developed, based on the combination of preconcentration/separation using dithizone-modified nanometer titanium dioxide (TiO2) as a solid phase extractant and determination by cold vapor atomic adsorption spectrometry (CVAAS). Dithizone was dissolved with alcohol and loaded on the surface of nano-sized TiO2 powders by stirring. The static adsorption behavior of Hg2 on the dithizone-modified nanoparticles was investigated in detail. It was found that excellent adsorption ratio for Hg2 could be obtained in the pH range of 7-8 with an oscillation time of 15 min, and a 5 mL of 3.5 mol·L-1 HCl solution could quantitatively elute Hg2 from nanometer TiO2 powder. Common coexisting ions caused no obvious influence on the determination of mercury. The mechanisms for the adsorption and desorption were discussed. The detection limit (3σ) for Hg2 was calculated to be 5 ng·L-1. The proposed method was applied to the determination of Hg2 in a mineral water sample and a Zhujiang River water sample. By the standard addition method, the average recoveries were found to be 94.4%-108.3% with RSD (n = 5) of 2.9%-3.5%.     

省煤器管开裂原因分析

对省煤器开裂管进行了化学成分及宏、微观分析。分析结果表明，在高温高压条件下，在其焊缝溶合区出现粗大的魏氏组织，管材中的珠光体组织产生了不同程度的球化，而母材组织又存在严重的带状组织。在过热条件下熔合区极易出现裂纹，并由此快速扩展，造成省煤器管开裂。     

进口VPSA制氧装置的流程特点及配置

详细介绍了进口的VPSA制氧装置的流程特点、工艺参数及主要设备的配置。实际运转证明 ,该制氧装置具有运行可靠、启动时间短、部分负荷性能优越、负荷转换速度快等优点 ,能满足金隆铜业有限公司的实际生产要求。     

百万吨级乙烯冷箱的设计

分析了百万吨级乙烯冷箱的设计难点和采取的对策，介绍杭氧设计、制造的乙烯冷箱的技术参数和设计方案，与国外公司设计方案的比较，说明杭氧乙烯冷箱的设计、制造技术与世界先进水平的差距大大缩小。     

A Cold Model Aerodynamical Test of Air-Staged Combustion in a Tangential Firing Utility Boiler

The purpose of this paper is to present the flow field in the 300MW tangential firing utility boiler that used the Low NOx Concentric Firing System （LNCFS）. Using the method of cold isothermal simulation ensures the geometric and boundary condition similarity. At the same time the condition of self-modeling is met. The experimental results show that the mixture of primary air and secondary air becomes slower, the average turbulence magnitude the relative diameter of the tangential firing enlarges of the main combustion zone becomes less and when the secondary air deflection angle increases When the velocity pressure ratio of the secondary air to the primary air （p2/p1） enlarges, the mixture of the secondary air and the primary air becomes stronger, the average turbulence magnitude of the main combustion zone increases, and the relative diameter of the tangential firing becomes larger. Because the over fire air （OFA） laid out near the wall has a powerful penetration, the relative diameter of the tangential firing on the section of the OFA is very little, but the average turbulence magnitude is great. When the velocity pressure ratio of the OFA to the primary air POFA/p1 increases, the relative diameter of the tangential firing on the section of the OFA grows little, the average turbulence magnitude becomes larger and the penetration of the OFA becomes more powerful.     

脉动燃烧控制技术在隧道式淬火炉上的应用

为解决隧道式淬火炉炉温分布不均匀的问题，采用了高速调温烧嘴脉动燃烧控制技术。实践证明：脉动燃烧控制对象是带延迟的一阶惯性环节，因此对控制对象采用常规的PID控制策略完全可行。还阐述了高速调温烧嘴脉动燃烧控制技术运用于隧道式淬火炉的优越性和取得的显著效果。     

山西铝厂锅炉水冷壁膨胀异常原因分析及对策

针对山西铝厂160t／h锅炉在实际运行中膨胀异常的问题，对不同的施工方法下，水冷壁膨胀量是否正常这一问题进行分析，找出了水冷壁膨胀异常的原因，并提出了解决对策。     

A generalized equation for the prediction of melting temperatures of homopolymers and copolymers

A generalized equation was derived to calculate the melting temperatures of homopolymers and copolymers. The Gibbs‐Thomson equation for homopolymers and a modified application to copolymers were derived using the proposed equation. The melting temperature T_m⁰ in the Flory equation corresponds to the melting temperature T_m^C,∞ of copolymer crystals with stems of infinite length. Also, T_m^C,n*, the melting temperature for copolymer crystals with stems containing the maximum possible number of structural units, n*, should be used instead of T_m⁰ as the basis of supercooling in crystallization. The proposed equation shows good agreement with experimental data for α‐alkene‐ethylene homogeneous copolymers.     

Rheology in Processing of in Situ Composites of Polypropylene and Low Melting Poing Metals

The low melting point metallic tin powder or alloy of tin and lead was blended with polypropy-lene. A kind of in situ composite has been prepared. The variations of torque were studied when the composites were mixed in Haake torque rheogeniometer. By way of capillary extrusion, effects upon rheology of the in situ com-posites of the low melting point metals (LMPM) and coupling agent for their different variety and content, were investigated. From flow curves, the results indicate that in situ composites mixed with the LMPM are a kind of pseudoplastic fluid. If the LMPM were melted, the higher the content of the LMPM , the lower apparent viscosity of composites. Meanwhile, when the coupling agent is added into composites, the viscosity of composite will go up first and drop then. This shows that the LMPM have a promoter flow action on the polypropylene.