双相位共轭镜的工作条件参数分析

本文讨论了纯扩散机制的光折变晶体用作单作用区的双相位共轭镜（ＤＰＣＭ）时的阈值耦合强度和允许的输入光强比范围，并与双作用区的情况进行比较后，给出了在输入光强比远离１的条件下，双相位共轭镜的正常工作的条件参数。     

砼回弹法测强统计分析

简述了砼回弹法测强与抗压强度对比试验的方法，得出了影响砼回弹测强的种种因素，通过统计分析给出了砼回弹测强的实用计算公式，从而就可在结构物上直接进行回弹测强，达到及时，方便，准确地了解结构物的强度．     

三峡工程左厂房坝导墙抗震计算分析

 用反应谱理论对三峡左厂房坝导墙3种典型设计断面型式进行了抗震计算分析比较，得出了其自振特性及地震动位移、动应力响应。对选定的设计断面型式Ⅲ进行了抗拉应力强度安全性评价。     

100 t伸缩臂履带式起重机臂架结构设计和优化分析

为确保100 t伸缩臂履带式起重机臂架结构设计的合理性,采用壳单元建立该起重机的有限元模型,用ANSYS计算臂架结构应力和应变,得到臂架的应力和应变分布,验证臂架的强度和稳定性.在起重机性能满足要求的情况下,以减轻结构自重为优化目标,以截面尺寸为优化设计变量,用ANSYS对臂架进行优化设计.优化设计后的臂架满足设计规范,臂架截面尺寸缩小、自重降低,整机性能得到提高.     

黄河淤积粉土的两种复合稳定方案与性能对比

为探索路基工程中黄河淤积粉土的稳定技术和性能保障方案,针对德州齐河县境内的黄河淤积粉土,在乳化沥青复合稳定粉土(AE稳定土)的研究基础上,采用无机/有机复合材料制备出一种复合固化剂(FG固化剂),研究了AE稳定土和FG稳定土2种稳定方案下粉土的抗压强度性质、水稳定性和抗冻融能力;结合XRD、SEM表征技术,探讨了FG固化剂的稳定机理。研究认为,FG固化剂稳定土较AE稳定土有着更高的无侧限抗压强度、回弹模量和承载能力,水稳定性良好,在抗冻融能力上有着比AE稳定土更好的效果。XRD与SEM分析表明,FG固化剂提供了活性矿物质,其复合胶凝效应和填充增强保障了粉土的抗压强度,高分子物质起到粘结颗粒界面、填塞孔隙的作用,降低了内部孔隙率;两者造成土体的最大干密度变大;与AE稳定土的稳定机理不同。FG固化剂的使用为黄河粉土的稳定和工程应用提供了参考方法。     

初生空化与液体抗拉强度的关系

自1983年开始以液体的抗拉强度作为其空化临界压强研究初生空化的比尺效应以来,该方法已得到进一步的应用和完善。本文就研究中遇到的一些问题,如关于空化灵敏度仪的校正,“零抗拉强度”的概念,试验设备中液体抗拉强度的动态变化以及在空化试验中使用该方法的技术和意义等作详细的阐述。     

Nondestructive characterization of the mechanical strength of diffusion bonds. II. Application of a quasi-static spring model

It has been shown that the acoustic response of imperfect interfaces may be described by a quasi-static spring model. In the present paper, experimental data on the geometry of the contacts between two diffusion-bonded blocks have been used to determine the spring stiffness of such interfaces which have been correlated with experimentally determined ultrasonic reflection coefficients. The correlation between the theoretical reflection coefficient and the spring stiffness was found to be in excellent agreement with experimentally-observed values, if the disbonds are of infinitesimally small thickness. For disbonds of finite thickness, the agreement is less satisfactory. Reasons for the discrepancy in the latter case are unknown at the present time.     

An enhanced,acoustic emission-based,single-fiber-composite test

In the single-fiber-composite (SFC) test, a fiber imbedded in a matrix is loaded in tension, resulting in a fragmentation of the fiber. In the conventional version of this test, the final fiber fragmentation length distribution is used with a micro-mechanical model to determine the average fiber/matrix interfacial shear stress. In the enhanced version of this test, one also determines the applied stress at each fiber fracture, and from this, one can evaluate the strength of the fiber at short gage lengths. In our measurement system, we utilize an acoustic emission (AE) technique to detect the fiber fractures and to locate the fiber breaks and so determine both the fiber failure stresses as well as the fiber fragmentation lengths while the test is in progress. Critical to the success of this test is a broadband AE system that utilizes point-like AE sensors, procedures for evaluatingin situ, the wavespeed of the first wave arrival and signal processing techniques for determining the arrival time of this signal as precisely as possible for a broad range of wave shapes. Here we describe the application of such an enhanced SFC test procedure to investigate the failure of a Nicalon fiber in an epoxy matrix.     

WC15Ni磁合金的质量控制

在WC15Ni无磁硬质合金生产过程中,选用粒度分布范围较窄的优质WC以及添加适量的Cr3C2,促进了抗弯强度的提高。     

混凝土抗硫酸盐侵蚀试验的一种新方法

提出了一个测定混凝土抗硫酸盐侵蚀能力的新方法。采用这种方法对超高强混凝土的抗化学腐蚀性能进行了试验，并和普通混凝土进行了对比。发现用一般硅酸盐水泥配制的超高强混凝土虽然在抵抗化学侵蚀能力方面比普通混凝土有所提高，但由于化学组成上的原因，它对高浓度的(NH4)2SO4等化学介质也难以抵抗。