Intermetallic phase formation in directionally solidified Al−Si−Fe alloy

The present study has been undertaken to better understand the solidification behavior of Al−Si−Fe alloys containing 7wt.% Si and 0.9wt.% Fe, with particular regard to the formation of phase during controlled solidification and influence of growth rates on intermetallic phase selection. The alloys studied were Al-7Si-0.9Fe alloys, which were produced by a modified Bridgman solidification arrangement. These alloys were solidified unidirectionally with different growth rates (1–30mm/min). The solidified microstructure of these alloys consists of the growth of primary aluminum and multiple second phase reactions.     

浅谈丁基胶垫与气门嘴的粘合

本文介绍了丁基橡胶垫与铜制气门嘴粘合的有关问题，并提供了解决方法。     

1-(2-吡啶偶氮)-2-萘酚分光光度法测定硫酸阳极氧化液中铜

研究了铜与1-(2-吡啶偶氮)-2-萘酚(PAN)的显色反应,建立了测定硫酸阳极氧化液中铜的新方法。以TritonX-100为增溶增敏剂,明胶作稳定保护剂,在酸性条件下Cu-PAN络合物稳定保持在水相中,直接进行光度分析。该络合物在558nm处有最大吸收峰,其表观摩尔吸光系数ε=2.25×104L.mol-1.cm-1。方法检出限为0.028μg/mL,线性范围为0～3.2μg/mL,用于测定硫酸阳极氧化液中的铜,加标回收率为98.2%～105.6%,相对标准偏差≤0.34%。     

Strain rate sensitivity of tensile properties in high Nb containing TiAl alloys

The effect of strain rate on the yield strength of high Nb containing TiAl alloy was studied. The results show that the strain rate sensitivity varies with the test temperature, and the yield strength is not sensitive to the strain rate at room temperature but significantly sensitive to the strain rate at high temperature. An increase of the strain rate or a decrease of the temperature results in an obvious change of fracture mode. It is found that the strain rate sensitivity of this alloy varying with temperature is due to the dislocation climb generated at high temperature.     

从国际铜加工行业的重组看我国铜加工行业的可持续发展

介绍了近年来国际铜加工行业的资产重组以及我国铜加工行业的特点,对正处于调整期的我国铜加工行业的可持续发展提出了一些建议。     

热交换器材料优化研究

对内螺纹铜管尺寸优化、铝箔厚度减薄前后的空调热交换器进行了单体性能实验和整机性能实验对比。实验结果表明优化后的内螺纹铜管、铝箔完全满足使用要求，为节约空调热交换器材料提供了有力的依据。     

Stresses in bent copper tubing: Application to fatigue and stress-corrosion cracking failure mechanisms

The residual and applied stresses in u-bent copper tubing are addressed in the context of both cyclic fatigue and stress-corrosion cracking. Failures as a result of fatigue and stress corrosion cracking in u-bent copper tubing have been observed to initiate at nonintuitive locations when only the applied stresses on the component are considered. This paper presents both qualitative classical and quantitative finite-element stress analysis results for the forming of u-bends. The resulting residual stress distributions are compared to fracture patterns generated by both fatigue and stress-corrosion cracking mechanisms.     

Strain rate sensitivity of the commercial aluminum alloy AA5182-O

The mechanical behavior of the commercial aluminum alloy AA5182-O is investigated at temperatures ranging from −120 to 150 °C and strain rates from 10⁻⁶ to 10⁻¹ s⁻¹. The strain rate sensitivity parameter is determined as a function of temperature and plastic strain, and the strain rate and temperature range in which dynamic strain aging leads to negative strain rate sensitivity is mapped. The effect of dynamic strain aging on ductility and strain hardening is investigated. The sensitivity of the measured quantities to the experimental method employed and their dependence on grain shape are discussed. The experimental data are compared with the predictions of a model constructed based on a recently proposed mechanism for dynamic strain ageing. The mechanism is based on the effect solute clustering at forest dislocations has on the strength of dislocation junctions. The model is shown to reproduce qualitatively the experimental trends.     

Fatigue damage accumulation of cold expanded hole in aluminum alloys subjected to block loading

Fatigue damage accumulation of cold expanded hole in aluminum alloys used in land transportation components was investigated. Tests were carried out using pre-cracked SENT specimens and inserting an expanded hole at the crack tip. The degree of the cold expansion was chosen equal to 4.3%. Tests were performed in two and four block loading under constant amplitude. Two sequences were compared.The increasing and the decreasing magnitude were compared. The experimental results were compared to the damage calculated by the Miner's rule and a new simple fatigue damage indicator. This comparison shows that the ‘model of the damage stress’, which take into account of the loading history, yields a good estimation of the experimental results. Moreover, the error is minimized in comparison to the Miner's model.