关于彩涂压型钢板构件设计中的选材问题

近年来 ,在彩涂压型钢板构件设计应用中 ,由于不重视、不了解如何合理选材 ,在实际工程的材料订货中也都不提出对材料性能的技术要求 ,致使供货材质、材性不能满足使用要求 ,存在降低彩板构件承载力或减少其使用寿命的隐患 ,应引起设计人员的注意。同时对当前如何按使用条件及材料供应条件合理地选定彩板材料的性能技术要求 ,包括基板钢材的级别及力学性能、板厚及公差控制要求、镀锌层质量与彩涂层类别以及参照的技术标准等 ,提出了一些建议 ,供设计应用参考。最后还对板的强度、厚度以及镀铝锌板的选用问题进行了讨论     

Resilient metal spring network silicone-matrix composite for separable interconnections

Resilient metal spring silicone-matrix conducting composites for separable interconnections in electronics were fabricated by the impregnation of silicone into a preform comprising randomly oriented C-shaped Cu-Be springs and a small proportion of Sn-Pb solder, which served to connect the springs at some of their intersections. Composites containing 6.1-9.8 vol.% total filler exhibited volume electrical resistivity 0.5-1.0 mΩ.cm and contact resistivity (with copper) 11-17 mΩ.cm². A compressive stress of about 30 kPa was needed for the low contact resistivity to be reached. The volume 17-26% and the contact resistivity increased by 5% after heating in air at 130-150°C for seven days. Composites containing <9 vol.% total filler showed no stress relaxation for seven days at 6.0% strain.     

Charge transfer resistance of spray deposited and compressed counter electrodes for dye-sensitized nanoparticle solar cells on plastic substrates

Electrochemical impedance spectroscopy was used to determine the effective charge transfer resistances of porous dye-sensitized solar cell counter electrodes prepared by low-temperature spray deposition and compression of conductive carbon and platinized Sb-doped SnO₂ powders on indium tin oxide-coated plastic substrates. The charge transfer resistances were 0.5–2 and 8–13 Ω cm², respectively, when using 3-methoxypropionitrile as the electrolyte solvent. The manufacturing method used lends itself to produce mechanically stable and even-quality electrodes in an easy and fast manner.     

Growth of CeO_2, Y_2O_3 Buffer Layers for YBCO Coated Conductor

~~Growth of CeO_2, Y_2O_3 Buffer Layers for YBCO Coated Conductor     

Catalyst instabilities during the liquid phase partial oxidation of methane

A promising catalytic system for the low temperature oxidation of methane to a methanol derivative has been investigated under both batch and semi-continuous operation in two different reactor types. The system comprises of a bimetallic palladium and copper(II) chloride catalyst contained in a trifluoroacetic acid (TFA) and an aqueous phase. Methane, oxygen and a co-reductant carbon monoxide constitute the gas phase. Typical operating conditions were a temperature of 85 °C and a pressure of 83 bar.

The yields of the methyl trifluoroacetate product observed in this present work were less than those obtained in other batch autoclave works, which employed only 4 ml of liquid phase, compared with 50 ml in this study. Furthermore, an encouraging initial product formation rate of ca. 40 mol/m³ h, quickly decreased after the first hour, and came to an apparent end after only 2 h. This observation had not been reported previously.

Work performed in a semi-continuous porous tube reactor (300 ml of re-circulating liquid phase) also showed the same reaction characteristics as in the batch reactor. Thus, the deteriorating product formation rate cannot be attributed to gaseous reactant depletion (batch operation). The results suggest problems associated with catalyst instabilities, e.g. with the previously elucidated Wacker chemistry.     

电解铜箔产业发展趋势

随着技术的进步,电解铜箔在厚度上迅速向薄、超薄方向发展,THE、RCC、CAC等特殊性能铜箔需求比例快速 增加,以锂离子电池为代表的新应用领域正在形成。     

纯铜双层辉光离子渗钛组织形成机理及性能分析

采用双层辉光离子渗金属技术对纯铜进行了渗钛处理。用配有能谱仪(EDS)的扫描电子显微镜(SEM)、X射线衍射仪和透射电子显微镜对合金层的显微组织形貌、钛含量分布、相组成及相结构类型进行了观察与测定，对合金层的形成机理进行了探讨，并对其性能进行了对比测定。结果表明：渗钛层由合金层和扩散层组成，合金层主要由TiCu (Cu)固溶体 TiCu4构成，TiCu4为Dla型有序相，TiCu为B2型有序相，扩散层为(Cu)固溶体。渗钛处理后纯铜的表面得到显著强化。     

On the permeation rate of copper extraction through liquid membranes

The understanding of the permeation rate of metal ions through liquid membranes is important for the design of such systems. In this paper, the permeation rates of copper ions through liquid surfactant membranes, including interfacial reaction rates and the diffusion rate of the copper ion, were analyzed using a model based on a mobilized hollow spherical globule configuration. The analysis shows that the extracting reaction is dominant at the external interface of the membrane and the stripping reaction is dominant at the internal interface; this means the reactions at both interfaces are not in equilibrium during the course of extraction. It also shows that the extraction rate, the diffusion rate and the stripping rate are not of equal value, especially at the early stage of the run.     

Effects of Substrate Temperatures on the Structure and UV-shielding Properties of TiO_2-CeO_2 Films Deposited on Glass by Radio-frequency Magnetron Sputtering

1Introduction Theultravioletrays(UV)insunlight(-4%)cantransmitintoroomthroughcommonfloatglass,theUVcanmakethematerialsintheroom,eg,paper,furni ture,textilefabricandplastics,becoloredanddeterio rated.ShieldingfromUVirradiationisofinterestinmanyfields.Formu…     

Growth and characterization of barium copper oxalate single crystals in gels

Barium copper oxalate was grown in silica hydrogel at ambient temperature. The effect of various parameters like gel pH, gel density, gel aging and concentrations of reactants on the growth of these crystals was studied. The crystals grown were characterized by chemical analysis, X-ray powder diffractometry, infrared spectroscopy, thermogravimetric and differential thermal analysis. The results of these observations are described and discussed.