硅酸铋晶体的蚀像形貌

本文研究了提拉法生长的硅酸铋晶体(BSO)的蚀像形貌,比较了{100},{110},{211},{111}面族的腐蚀像特征和腐蚀速度,并用周期性键链(PBC)的形貌理论分析了腐蚀形貌。通过蚀像形貌特征便可方便地进行晶体定向,准确地确定各族晶面之间的相对位置和极轴的方向等。     

Properties of ligno‐cellulose fiber Hildegardia

Studies on some properties such as the density, the degradation temperatures, the morphology and the spectral features of the ligno‐cellulose fiber Hildegardia were carried out in both untreated and alkali treated form. The fibers are found to have good morphology and moderate initial and final degradation temperatures. On alkali treatment, the lignin was found to be eliminated. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 2216–2221, 2002     

局部施肥对植株生长及根系形态的影响

本文论述了局部施肥对植株地上部与地下部的影响。局部施肥促进了施肥区根系的发达 ,第一侧根与第二侧根较多 ,根的吸收表面积增多 ,根鲜重增加 ,对养分的吸收能力增强 ,但整个根系与地上部的干鲜重下降。     

Surface tailoring of an ethylene propylene diene elastomeric terpolymer via plasma‐polymerized coating of tetramethyldisiloxane

In the research presented here, we explore the use of a low‐energy plasma to deposit thin silicone polymer films using tetramethyldisiloxane (TMDSO) (H(CH₃)₂? Si? O? Si? (CH₃)₂H) on the surface of an ethylene propylene diene elastomeric terpolymer (EPDM) in order to enhance the surface hydrophobicity, lower the surface energy and improve the degradation/wear characteristics. The processing conditions were varied over a wide range of treatment times and discharge powers to control the physical characteristics, thickness, morphology and chemical structure of the plasma polymer films. Scanning electron microscopy (SEM) shows that pore‐free homogeneous plasma polymer thin films of granular microstructure composed of small grains are formed and that the morphology of the granular structure depends on the plasma processing conditions, such as plasma power and time of deposition. The thicknesses of the coatings were determined using SEM, which confirmed that the thicknesses of the deposited plasma‐polymer films could be precisely controlled by the plasma parameters. The kinetics of plasma‐polymer film deposition were also evaluated. Contact angle measurements of different solvent droplets on the coatings were used to calculate the surface energies of the coatings. These coatings appeared to be hydrophobic and had low surface energies. X‐ray photoelectron spectroscopy (XPS) and photoacoustic Fourier‐transform infrared (PA‐FT‐IR) spectroscopy were used to investigate the detailed chemical structures of the deposited films. The optimum plasma processing conditions to achieve the desired thin plasma polymer coatings are discussed in the light of the chemistry that takes place at the interfaces. Copyright © 2004 Society of Chemical Industry     

基于复合顺序形态变换的车牌边缘检测

边缘检测是图像分割的重要环节,边缘提取的好坏直接影响了整个图像处理的效果。数学形态学用具有一定形态结构的“结构元素”去度量图像的形态,以解决图像处理和分析问题。文章通过对多种边缘检测方法的分析比较,结合高速公路路口汽车图像噪声大的特点,提出了基于复合顺序形态变换的车牌边缘检测。该方法不但能有效地改善有噪图像边缘检测的效果,鲁棒性好,而且并行快速,便于硬件实现。     

Effect of Reactor Ambient Pressure on the Morphology of Spray Dried Magnesium Sulphate Powders

The effect of reducing the reactor air pressure on the morphology of spray dried magnesium sulphate powders is investigated, experimentally. A reactor, capable of drying and pyrolyzing solution sprays at low pressures, is designed and manufactured. A vibrating mesh nebulizer is employed to generate the spray. Four different pressures, starting from 60 Torr to the atmospheric pressure, and two different reactor air temperatures of 130°C and 420°C, are considered. In addition, two different concentrations of magnesium sulphate solutions are tested. The results are explained based on the effect of reactor air pressure on the droplet evaporation rate.     

Morphology development in polyethylene/polystyrene blends: the influence of processing conditions and interfacial modification

The influence of processing conditions and interfacial modification on the morphology evolution and the composition range within which fully co‐continuous high density polyethylene/polystyrene blend structures can exist during blending in a single screw extruder was studied. Blends ranging from pure A to pure B component, with and without compatibilizer, were prepared under two different shear rates. It was found that high shear rates displaced the breakdown–coalescence balance of the dispersed nodules to the side of coalescence, narrowing the percolation domain and the critical composition for full co‐continuity decreased with increasing shear rates. The addition of a tri‐block compatibilizer induced the percolation threshold of the polystyrene phase to begin at lower percentages of polyethylene but the phase inversion point did not change. The experimental results are discussed in the light of various theoretical models. Copyright © 2005 Society of Chemical Industry     

Influence of Gaseous Atmosphere on Morphology and Cellular Fatty Acid Composition of Campylobacter jejuni

ABSTRACT: We evaluated the effect of growth environment on morphology and fatty acid (FA) profiles of 2 strains of C ampylobacter jejuni (ATCC 29428 and 33560) grown under various gaseous conditions. Viable counts were determined by plate count and percentages of coccoid cells. FA profiles were measured by gas chromatography. Plate counts were lowest when cultures were grown in air and highest in CO₂ (10%), O₂ (5%), and N₂ (85%). For 29428, percentages of coccoid cells did not differ among treatments. For 33560, percentages of coccoid cells were greater than for 29428 and varied among treatments (13% to 87%). There were no significant ( P > 0.05) relationships between percentages of coccoid cells and amounts of individual or combinations of FA either between or within strains.     

The effect of support morphology on the reaction of oxidative dehydrogenation of ethane to ethylene at short contact times

The oxidative dehydrogenation of ethane is carried out in short contact time reactors over Pt and LaMnO₃ based catalysts supported on a large number of different ceramic substrates (45, 60 and 80 ppi foam monoliths and 200, 400, 600, 900 and 1200 cpsi honeycomb monoliths). Experimental results, obtained under the same conditions at varying the C₂H₆/O₂ ratio, showed that the highest performance in terms of ethylene selectivity and yield is always attained on LaMnO₃ catalysts. Furthermore, the results are significantly influenced by the morphology and cell density of the support, with 45 and 60 ppi foams and 400 and 600 cpsi honeycombs giving the best performance. The experimental results are explained by means of geometrical and fluid dynamic considerations on the support, and by means of a 2D mathematical model, which clearly indicates an optimal intermediate cell density for maximising ethylene selectivity and yield.     

Application of ultrasonic waves in activation of microcrystalline cellulose

In this work, microcrystalline cellulose (MCC) was activated with ultrasonic waves. The influences of ultrasonic treatment on the changes of supramolecular structures and morphology structure were studied by WAXS and SEM. The accessibility of the MCC was characterized by water retention value (WRV) and specific surficial area. The influence of ultrasonic treatment on the reactivity of MCC was investigated through the reaction of MCC being oxidized into 2,3‐diadehyde cellulose (DAC) by periodate sodium. The mechanism of the reactivity change of ultrasonically treated MCC was examined. The results showed that the degree of crystallinity of MCC decreased and the degree of polymerization showed little change after treatment with ultrasonic waves. The morphologial variation of the treated MCC was significant when compared with the untreated MCC, which contribute to the improvement of accessibility. The aldehyde content of DAC prepared from ultrasonically treated MCC was improved from 64.19 to 85.00%, indicating that the regioselective oxidation reactivity of MCC was significantly improved. The aldehyde content was found to first increase with time of ultrasonic treatment to a point, and then decrease as time progressed. In addition, the aldehyde content was found to increase with an increase in ultrasonic power. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008