采用中频炉冶炼LCC低温钢的实践与应用

介绍了中频炉炼LCC钢时 ,通过选择合适的炉衬和包衬材料 ,严谨的操作工艺 ,降低钢水中的气体和夹杂 ,从而使LCC钢低温性能合格率大大提高     

玻璃包覆纯铜微丝的制备与表征

采用熔融纺丝法制备了玻璃包覆纯铜微丝,对微丝进行了组织观察以及尺寸和缺陷表征,提出了不同冷却条件下的纯铜芯丝凝固过程模型,讨论了制备过程中存在的问题并提出了相应的解决方案.结果表明:在空气中自然冷却凝固的纯铜芯丝内部组织为细等轴晶,加冷却水快速冷却凝固制备的纯铜芯丝内部的晶粒沿着微丝长度方向呈竹节状整齐排列;当微丝外径为45μm、芯丝直径为25 μm时,外径尺寸波动在6%以内,芯丝直径误差小于4%;当原料质量存在问题或制备过程中拉丝速度、冷却速度等工艺参数匹配不合理时,易导致芯丝表面存在凹坑和凹槽等缺陷.     

灰铁铸件牌号要求与熔炼配料选择

由于铸件壁厚对其性能有明显影响，牌号要求相同、壁厚不同的灰铁铸件必须采用不同的成分和配料。介绍不同灰铁铸件牌号标准的对照，并用生产实例说明如何根据图纸牌号要求、铸件结构和使用性能要求选择化学成分控制标准和熔炼配料。     

WD615气缸体铸件材料性能的改善

WD615气缸体铸件曾发生化学成分不稳定、铸件本体组织粗大、铁素体含量偏高、硬度偏低等质量问题，为此，采取了如下措施：1）加强熔炼用材料的质量控制；2）提高冲天炉的熔炼质量；3）改进熔炼工艺（调整C,Si量，采用Cu-Cr-Sn合金化；降低浇注温度）；4）改进孕育工艺；5）采用炉前快速检测技术；6）加强铸件本体质量检测。结果表明，缸体铸件的化学成分、金相组织及力学性能均满足技术要求。     

低成本钛合金制备技术研究进展

为了降低钛合金的生产成本,美、俄、日、中等国家都在此领域进行了广泛的研究。对国际上新出现的以降低钛合金生产成本为目的的新冶金方法、新的低成本合金化钛合金和新的加工生产技术进行了综述。目前,国际上研究较为活跃的低成本钛冶炼新方法有FFC剑桥法、Armstrong工艺、EMR复合阳极工艺、SRI工艺、Idaho钛工艺及OS工艺。其中,以FFC剑桥法为代表的TiO2直接电解还原方法,最有希望成为替代传统Kroll工艺的新方法。     

Analysis of Intermetallic Phases Formed on Surface Vapor Oxidized H13 Hot Work Steels in Molten Aluminum

In this paper, the author dipped surface vapor oxidized H13 steel specimens into 700℃ molten aluminum liquid for a certain period of time. Analyze the intermetallic phases formed on the H13 samples surface with optical microscope and X-ray diffraction method. The observation of immersion test sample's cross-section shows that Fe3O4 film will protect die substrate from molten aluminum erosion. The identification of the intermetallic phases reveals that they consist of 2parts, which is named as the composite layer and the compact layer. Further investigations are made in order to know the phase constituents of the 2 layers, they are Al8Fe2Si (outer composite layer), (AlCuMg) and Al5Fe2 (compact layer),respectively. The experimental results show that on the same specimen, a convex surface with bigger radius of curvature is more likely to be molten and the melting loss speed is also faster than a flat and smooth surface. The thickness of compact layer on a smooth surface is much bigger than that of the convex surface. Therefore, the author supposes the compact layer is favorable in stabilizing the die surface material from further melting loss, as their formation on the die surface, the melting loss speed will decrease.     

Suppression of the development of pores during laser-induced surface dispersion of TiC into aluminium, by means of a static magnetic field

A static magnetic field having the strength of B=0.6 T has been used as an additional process parameter in order to suppress the establishment of pores while dispersing TiC particles in surface layers of aluminium alloys using a laser. The migration of hydrogen towards regions of high temperatures within the melting pool can lead to the creation of gas bubbles, therefore yielding pores after resolidification in the processed layer. This mechanism (known for instance in welding technologies of aluminium) could be suppressed by Lorentz-forces induced by an externally applied magnetic field. It could be shown experimentally that magnetic fields could assist laser surface treatment processes beneficially if higher beam powers were coupled in. This may be interesting if, for instance, thicker dispersed layers should be achieved.     

Investigation on gradient material fabrication with electron beam melting based on scanning track control

A new electron beam control system was developed in a general vacuum electron beam machine by assembling with industrial control computer, programmable logic control （PLC）, deflection coil, data acquisition card, power amplifier, etc. In this control system, scanning track and energy distribution of electron beam could be edited off-line, real-time adjusted and controlled on-line. Ti-Mo gradient material （GM） with high temperature resistant was fabricated using the technology of electron beam melting. The melting processes include three steps, such as preheating, melting, and homogenizing. The results show that the GM prepared by melting technology has fine appearance, and it has good integrated interface with the Ti alloy. Mo and Ti elements are gradually distributed in the inter.face of the gradient material. The microstructure close to the Ti alloy base metal is α ＋ β basket-waver grain, and the microstructure close to the GM is a single phase of β solid solution.     

注射成型塑化过程的可视化实验研究

利用自行开发的可视化实验装置对注射成型的塑化过程进行了系统的观察,着重讨论了不同的工艺条件对塑化性能的影响,同时借助示踪粒子对塑化过程的重要参数——固相速度进行了测量。实验所取得的数据为注射成型熔融模型的建立和对模型的验证提供了依据,同时也是注射螺杆优化设计的基础数据。     

回收PET共混物的非等温结晶和熔融行为

采用双螺杆挤出机制备了聚丙烯(PP)/回收聚对苯二甲酸乙二酯(r-PET)、r-PET/马来酸酐接枝PP(PP-g-MAH)和r-PET/甲基丙烯酸缩水甘油酯接枝PP(PP-g-GMA)共混物,并研究了共混物组成、熔融温度与时间以及降温速率对共混物非等温结晶与熔融行为的影响.结果表明,r-PET与PP共混,结晶温度均提高,这与组分间起到异相成核诱导结晶作用有关.r-PET结晶温度随PP-g-MAH用量增加而降低,但受PP-g-GMA用量影响较小;r-PET可提高PP-g-MAH结晶温度,但降低PP-g-GMA结晶温度.熔融温度提高,共混物中PP结晶温度和熔点均降低,r-PET熔融峰形和熔点取决于共混物的熔融温度及界面相互作用.