超瞬态凝固增材制造梯度整体涡轮叶盘用高温合金粉末特性研究Ⅱ：叶片用合金粉末

本文针对超瞬态凝固增材制造梯度整体涡轮叶盘高温合金叶片用合金粉末特性开展研究。根据合金的承温能力和JMatPro相平衡计算结果,选用DZ4125作为叶片材料,K418作为叶盘轮缘部位材料。采用真空感应熔炼氩气雾化制粉(VIGA)制备DZ4125高温合金粉末,筛分至53-105μm粒度范围,采用采用差示扫描量热分析（DSC）、场发射扫描电镜（FESEM）和能谱（EDS）、激光粒度仪、动态图像粒度粒形分析仪以及综合粉体性能测试仪对DZ4125高温合金粉末的相变温度、显微组织、析出相成分、元素偏析行为、粒度、粒形、松装密度、振实密度和流动性进行系统表征。结果表明：DZ4125比K418合金的固液凝固温度范围宽,过渡区DZ4125+K418混合成分合金其液相线温度和MC碳化物开始析出温度介于两种合金之间,γ′开始析出温度与两种合金相当。DZ4125合金粉末形貌主要为球形和近球形,表面和截面显微组织主要呈树枝晶结构。所含元素中偏析倾向较强的元素有Hf、Ta、Ti、Mo和W,而偏析倾向弱的元素包括Ni、Co、Cr和Al。粉末内部枝晶间区分布有细小的MC碳化物,尺寸约为200nm。激光衍射和动态图像分析法测得的DZ4125粉末粒度值接近,中位径D50分别为70.2μm和72.8μm。动态图像法测得DZ4125合金粉末具有较好的球形度,SPHT和b/l均值分别为0.91和0.86。所选DZ4125高温合金粉末具有较好的松装密度、振实密度和流动性,其松装和振实密度分别达到合金理论密度的52%和63%,压缩度为17.7%,且粉末具有较好的流动性（20.79 s?(50 g)-1）。     

镍基高温合金GH202高温氧化后的微观组织演变

研究了镍基高温合金GH202在800~1100 ℃高温氧化后晶粒、碳化物和强化相的演变过程。采用透射电子显微镜、扫描电子显微镜和电子背散射衍射对其微观结构进行了表征。结果表明：镍基高温合金的硬度随氧化温度的升高而降低,1100 ℃氧化100 h后,硬度降低了43.5%。800和900 ℃氧化后晶粒生长速度较慢,而经900 ℃氧化后晶界碳化物析出显著增加。在1000和1100 ℃氧化后,晶粒尺寸明显增大。氧化过程中晶界迁移是由晶界两侧自由能差决定,温度越高,晶界向曲率中心迁移越快,大量细小晶粒被吞并形成了大晶粒。大块状碳化物（MC）分解成大量的碳原子,与Cr原子结合形成少量的富Cr颗粒状M₂₃C₆。在900 ℃氧化150 h后,M₂₃C₆演化为富Ti的M₆C。随着氧化温度的升高,碳化物在γ相中回熔。在800、900和1000 ℃氧化后,γ′相逐渐长大,在1100 ℃氧化100 h后,完全溶解于γ相。     

Phase constitution,microstructure and mechanical properties of a Ni-based superalloy specially designed for additive manufacturing

In this study, a kind of Ni-based superalloy specially designed for additive manufacturing (AM) was investigated. Thermo-Calc simulation and differential scanning calorimetry (DSC) analysis were used to determine phases and their transformation temperature. Experimental specimens were prepared by laser metal deposition (LMD) and traditional casting method. Microstructure, phase constitution and mechanical properties of the alloy were characterized by scanning electron microscopy (SEM), transmission scanning electron microscopy (TEM), X-ray diffraction (XRD) and tensile tests. The results show that this alloy contains two basic phases, γ/γ', in addition to these phases, at least two secondary phases may be present, such as MC carbides and Laves phases. Furthermore, the as-deposited alloy has finer dendrite, its mean primary dendrite arm space (PDAS) is about 30-45 μm, and the average size of γ' particles is 100-150 nm. However, the dendrite size of the as-cast alloy is much larger and its PDAS is 300-500 μm with secondary and even third dendrite arms. Correspondingly, the alloy displays different tensile behavior with different processing methods, and the as-deposited specimen shows better ultimate tensile stress (1,085.7±51.7 MPa), yield stress (697±19.5 MPa) and elongation (25.8%±2.2%) than that of the as-cast specimen. The differences in mechanical properties of the alloy are due to the different morphology and size of dendrites, γ', and Laves phase, and the segregation of elements, etc. Such important information would be helpful for alloy application as well as new alloy development.     

GTD-111高温合金瞬时液相连接过程中显微组织的变化

研究连接温度和时间对瞬时液相连接GTD-111高温合金显微组织的影响.连接过程采用BNi-3填料,在1080、1120和1160℃下,分别进行195、135和90 min的等温凝固,再进行均匀化热处理.结果表明,在冷却过程中,接头区域连续形成富Ni硼化物、Ni?B?Si三元化合物和共晶γ的金属间化合物和共晶化合物.随着...     

Room temperature tensile deformation behavior of a Ni-based superalloy with high W content

K416B Ni-based superalloy with high W content has good high temperature properties and low cost, which has a great development potential. To investigate the room temperature tensile property and the deformation feature of K416B superalloy, tensile testing at room temperature was carried out, and optical microscopy (OM), scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were used to analyze the deformation and damage mechanisms. Results show that the main room temperature tensile deformation features of the K416B nickel-based superalloy are dislocations slipping in the matrix and shearing into γ′ phase. The <110> super-dislocations shearing into γ′ phase can form the anti-phase boundary two coupled (a/2)<110> partial-dislocations or decompose into the configuration of two (a/3)<112> partial dislocations plus stacking fault. In the later stage of tensile testing, the slip-lines with different orientations are activated in the grain, causing the stress concentration in the regions of block carbide or the porosity, and cracks initiate and propagate along these regions.

     

铸造镍基高温合金增材修复技术的研究现状

铸造镍基高温合金广泛用于燃气轮机与航空发动机叶片等高温部件,长时间运行过程中经常发生叶片局部损伤失效,其维修或更换成本极高.通过增材修复来恢复局部损伤叶片的性能,将极大地降低制造成本、缩短制造周期、节约资源,具有极大的社会效益和市场价值.本文针对燃气轮机与航空发动机用铸造镍基高温合金部件的服役工况与失效形式,结合铸造镍...     

航空航天用金属表面热防护涂层的研究进展

高温合金材料凭借其优异的综合性能而广泛应用于航空航天领域热端部件.近年来,随着航空航天技术的不断发展,飞行器的热端部件正逐渐面临着更为严峻和复杂的服役环境,因此对高温合金的耐高温、抗氧化等使用性能提出了更高的要求.表面涂层技术由于具有约束条件少、可设计性强、技术类型和材料的选择空间大、经济环保等优点,成为目前最常用的热...     

PdW20包晶合金的凝固组织及相选择

考察了凝固速率在50~1.8×103μm/s范围内的PdW20合金凝固组织及凝固速率对微观组织形态和领先相的影响。结果表明,三种不同凝固条件下的凝固组织由初生W相、包晶(Pd)相和固溶体Pd相组成。随着凝固速率增大,合金组织从树枝晶转变成等轴晶,晶粒大小快速减小。合金组织存在显微偏析,并且随着凝固速率增大,晶内与晶界上的成分差值减小。在3.2×102μm/s凝固速率下,观察到领先相W在进行包晶反应时不完全,还有部分W剩余。     

K403镍基合金热暴露下的组织稳定性研究

采用拉伸试验、扫描电镜、透射电镜等试验分析手段研究了K403镍基铸造高温合金在温度为800~950℃、时间为50~200 h热暴露后组织稳定性与性能的变化。结果表明:随着热暴露温度的提高,γ’相聚集长大、边角发生钝化,γ’相形貌由方形向圆形或近圆形转变,部分γ’相发生定向排列连接粗化的现象越显著;合金仅在850和900℃热暴露条件下有少量有害的针状TCP脆性相(σ相)析出;随着热暴露温度的升高,合金抗拉强度下降幅度增大,延伸率呈上升趋势。其主要原因是由于γ’相的粗化聚集和TCP相的析出。     

DZ125高温合金超高周疲劳裂纹萌生与扩展

裂纹的萌生与扩展是研究合金材料超高周疲劳行为的重要方面.本研究分析与探讨了温度和表面状态对DZ125合金的超高周疲劳裂纹萌生与扩展特征的影响.不同温度下,DZ125合金的超高周疲劳裂纹萌生位置和扩展方式不同.室温下,裂纹均沿表面起源,裂纹扩展以拉伸模式为主;700 ℃下,裂纹均沿亚表面起源,裂纹扩展以剪切模式为主.室温下,DZ125合金经激光冲击处理前后的超高周疲劳裂纹萌生位置和扩展方式均存在差异.经过激光冲击处理后,裂纹萌生于合金的内部孔洞缺陷,裂纹扩展完全以剪切模式进行.