DLL23XA双侧向测井仪的研制

以往双侧向测井仪动态范围小，测量精度低，为此开发了DLL23XA双侧向测井仪。该仪器主要单元采用厚膜电路，稳定性、一致性好；深、浅屏流源采用可变功率控制，提高了仪器的动态范围。仪器采用3506P例进行数据传输，可方便地配接各种地面系统。     

CZF90测井中子发生器使用寿命浅谈

Ｃ／Ｏ测井中采用同步测量技术来分析非弹性γ与俘获γ，但在一些ＭＳＩ Ｃ／Ｏ测井中发现非弹性γ的一小部分或一大部分超前于非弹性门而进入俘获门，我们把这一问题叫做“错位”。“错位”使得Ｃ／Ｏ的ＣＩ值不正常，测井曲线不合格。这样的仪器不能用来测井。吉林油田测井公司碳氧比维修班成功地解决了Ｃ／Ｏ仪器“错位”等技术难题，在该油田所使用的ＣＺＦ９０－９４－０９发生器已测井８８口，累计打靶时间２３０ｈ，并且至今     

涂层材料的断裂分析(英文)

和基体厚度相比,涂层很薄,因此细观力学模型可把基体作为半无限弹性体。由于涂层和基体材料的膨胀系数及弹性系数不匹配,涂层材料中残余热应力的解析解为 E_c/(1-γ_c)·(α_s-α_c)△T。用有限元法校核,该应力和解析解吻合得好。通过对涂层产生裂纹驱动力和断裂韧性的讨论,提出了抗裂涂层厚度公式。     

液压胀形轧辊油槽深度的确定

对液压胀形轧辊（即国外的ＶＣ轧辊）辊套热装后的弹性变形进行了有限元分析，给出了确定油槽最小深度的计算公式。本文的有限元计算结果与实验结果吻合，某些结论可为液压胀形轧辊的结构设计提供理论依据。     

Longitudinal elastic waves in columns due to earthquake motion

An analysis is presented of longitudinal waves in a thin elastic column. Velocity is specified at one end, and the boundary condition at the other end is expressed in terms of a range of effective impedances of an attached structure. Propagation, reflection and interference of the waves are followed by the method of characteristics. Integration of differential equations along characteristics yields the wave-induced stress, which is then applied to problems of earthquake excitation. Numerical examples are given for recorded updown ground motion of the Kobe Earthquake.     

FEATURE SOLID MODELING TOOL SYSTEM:FSMTS

In conformity with the principle of Design for Manufacture,feature-based design strate-(?)es have been developed.As the“feature”is relevant to the“macro process plan”and“macro NCprograms”,obviously,“feature”is beyond the power of conventional solid modellers.Neverthe-less,substantial breakthrough has not been made in the solid modeling field,except“feature at-taching”or“feature recognizing”methods have been taken on.In this paper,the theory,concepts,system architecture,and algorithm principles of solid modeling tool system have beenrepresented.The practice of Feature Solid Modeling Tool System (FSMTS) developed atHuazhong University has proved that the tool may be a new foundation of Feature-Based Design.     

铣槽专用夹具设计

从零件的几何形状 ,配合要求入手 ,设计零件铣槽的专用夹具     

On an invariance principle for unilateral contact at a bimaterial elastic interface

This paper examines the axisymmetric elastostatic problem related to the unilateral receding contact at a pre-compressed smooth bimaterial elastic interface. The separation at the interface is caused by the action of axisymmetric stress fields of unequal magnitude, which are applied at any location of the separate halfspace regions. The analysis of the problem focuses on the determination of the zone of separation as a function of the pre-compression, the magnitudes and locations of the axisymmetric stress fields inducing the separation, and the elasticity characteristics of the halfspace regions. It is found that the radius of the separation zone can be evaluated in explicit form. In the particular instance when the loadings applied at the surface of the halfspace regions are equal in magnitude and distribution, the analysis reveals that the radius of the separation zone is independent of the elasticity properties of the halfspace regions and can be evaluated in exact closed form.     

弹性筛管防砂技术

弹性筛管防砂技术是根据稠油油藏高轮次吞吐和蒸汽驱井防砂生产需要而研制的筛管防砂新技术。进行了筛管结构优化、加厚过滤单元外罩设计、固定方式研究、弹性过滤材料筛选、防腐实验研究等。室内试验表明，筛管的过流能力在900cm^2／m以上、渗透率在100μm^2以上、筛管抗内、外压强度达到20MPa、防砂粒径在0.1mm以上、耐温350℃、pH值在3～12之间不被腐蚀。现场试验证明，该技术防砂和抗堵塞性能好，防砂有效期长，地层适应性强，施工简便，防砂生产效果明显，具有良好的应用前景。     

节理岩体的代表单元集合体模型及弹性参数预测

本文明确提出了节理岩体“代表单元集合体”的概念和模型，通过对节理岩体的“代表单元集合体”进行数值模拟，研究了节理岩体的“代表单元集合体”的变形特性，建立了节理岩体的弹性模型，提出了预测节理岩体宏观等效弹性参数的计算机模拟方法，并将其应用于岩体工程稳定性分析中。