Improving corrosion resistance of Q235 steel by Ni-Cr alloyed layer

Ni-Cr alloyed layer was formed on surface of Q235 steel by double glow plasma surface metallurgy to improve the corrosion resistance of substrate. The composition and microstructure of alloyed layer was analyzed by SEM and XRD. Potentiodynamic polarization and electrochemical impedance spectroscopy was applied to evaluate the corrosion resistance of the alloyed layer. The results showed working pressure had a great effect on structure of Ni-Cr alloyed layer, and the dense and smooth alloyed layer was prepared at 50 Pa working pressure. Compared with substrate, Ni-Cr alloyed layer exhibited higher corrosion potential, lower corrosion current density and larger charge transfer resistance, which indicated that Ni-Cr alloyed layer significantly modified the corrosion resistance of Q235 steel.     

锂离子电池负极材料 Na2Li2Ti6O14的嵌脱锂过程动力学研究

为了研究钛酸钠锂(Na2Li2Ti6O14)负极材料嵌脱锂的动力学行为,用溶胶-凝胶法合成 Na2Li2Ti6O14负极材料,采用 X 射线衍射法(XRD)和电子显微镜(SEM)分别对材料进行物相分析和微观形貌的观察.采用恒流充放电测试、循环伏安法(CV)和恒电流间歇滴定法(GITT)研究了 Na2Li2Ti6O14的电化学性能和嵌脱锂过程动力学.研究结果表明,制备的 Na2Li2Ti6O14材料纯度高,结晶度良好,循环稳定性好;由不同扫描速率的循环伏安法测出的 Na2Li2Ti6O14中锂离子在氧化、还原峰对应的化学扩散系数 Da和 Dc分别为7.3×10-11和7.8×10-11cm2/s;由恒电流间歇滴定技术测得的锂离子在 Na2Li2Ti6O14电极中的扩散系数为10-11~10-8cm2/s.     

La1-xCexNi3.54Co0.78Mn0.35Al0.32贮氢合金相结构和电化学性能的研究

采用真空电弧熔炼和热处理方法制备了La1-xCexNi3.54Co0.78Mn0.35Al0.32(x=0.1,0.2,0.3,0.4,0.5,0.6)贮氢合金.X射线衍射(XRD)分析表明,合金含有单一CaCu5型六方结构相.电化学性能测试表明,随着x的增加,合金的最大放电容量从348.1mAh/g(x=0.1)单调地减小到310.1 mAh/g(x=0.6);HRD1200先从28.6%(x=0.1)增加到65.4%(x=0.5)然后降低到60.1%(x=0.6),归因于合金表面的电催化活性和合金体内氢原子扩散速率均随x的增大先增大后减小.     

柠檬酸根辅助电沉积制备铂纳米粒子及其制备条件的优化

以氧化铟锡（ITO）透明导电玻璃为基体,在柠檬酸根存在下,采用恒电位电化学沉积法制备铂纳米粒子,并通过改变施加电位、柠檬酸钠浓度、前驱体浓度和电解质浓度来优化铂纳米粒子的制备条件.利用X射线衍射（XRD）表征在ITO表面沉积的Pt颗粒的晶相结构,并运用循环伏安法（CV）测定Pt/ITO电极在酸性介质中的电催化氧化性能.实验结果表明,在施加电位为-0.3V、H2PtCl6浓度为0.8mmol/L、柠檬酸钠浓度为20mmol/L和电解质HClO4浓度为0.1mol/L的条件下,制备出的铂纳米粒子的电催化性能较好.     

Influence of zinc on electrochemical discharge activity of Mg-6%Al-5%Pb anode

Mg-6%Al-5%Pb (mass fraction) anodes with different contents of zinc were prepared by melting and casting. The electrochemical discharge behavior of these anodes in 3.5% NaCl solutions was investigated by galvanostatic test and electrochemical impedance spectroscopy (EIS). The microstructures and the corroded surfaces of these anodes were studied by scanning electron microscopy (SEM) and emission spectrum analysis (ESA). The phase structures and the corrosion products of the anodes were analyzed by X-ray diffraction (XRD). The results show that zinc promotes the grain refinement of Mg-6%Al-5%Pb anode and makes the average discharge potential of Mg-6%Al-5%Pb anode more negative during galvanostatic test. Mg-6%Al-5%Pb anode with the addition of 1% (mass fraction) zinc has the best electrochemical performance. The activation mechanism of zinc to Mg-6%Al-5%Pb anode is as follows: The hydrolyzation of dissolved Zn²⁺ ions reduces the pH value of the solution near the surface of the anode and accelerates the dissolution of Mg(OH)₂ film; The precipitated Zn(OH)₂ with similar structure as Mg(OH)₂ combines with Mg(OH)₂ film easily and makes it break down.     

多孔Co3O4纳米片的制备及其电化学性能研究

采用溶剂热法制备片状Co(CO3)0.5(OH).0.11H2O前驱物,经400℃煅烧2 h即可得到多孔Co3O4纳米片.通过场发射扫描电镜(FESEM)和透射电镜(HRTEM)观测了纳米片的形貌,利用X射线衍射(XRD)分析了纳米片的结构,通过循环伏安、恒流充放电和交流阻抗测试了材料的电化学电容性能.结果表明:多孔Co3O4纳米片厚度约为50 nm,孔径主要分布在10 nm左右;0.5 A/g恒流充放电情况下,比容量高达707 F/g,当电流密度高达8 A/g时比容量依然高达547 F/g;同时,该材料循环1 000次后,容量保持率为97.4%.     

Ag_2Se/Se/SiO_2纳米复合物的制备及其光电性质

通过两步法成功合成了Ag2Se/Se/SiO2纳米复合物。首先采用Na2SiO3和Na2SeSO3为反应物,制得纳米Se/SiO2前驱物,然后将前驱物与AgNO3反应制得产物。讨论了产物的形成机理,利用TEM、XRD、UV-vis、FT-IR、LRS、PL等方法对产物进行了表征,并对产物的电化学和电致发光特性进行了研究。结果表明,产物有一定的电化学活性,并有较好的电致发光行为。