弱酸性铵盐与碱性锌酸盐双缸套镀锌工艺及低铬钝化

总结了弱酸性链盐镀锌和碱性锌酸盐镀锌的优缺点，并综合两者的优点，提出了一种弱酸性铵盐与碱性锌酸盐双缸套镀锌工艺。钝化膜的性能得到了改善。     

接插件的表面处理

综述了接插件连续镀金、钯、锡的电镀工艺，包括设备、镀液和镀层性质。     

均匀设计试验方法及其在Ni-P-MoS2化学镀上的应用

均匀设计是基于试验点在整个试验范围内均匀散布的一种试验设计方法。介绍了该法的特点及其软件的基本功能与基本操作过程。从均匀设计试验方案的建立、试验结果的回归分析及优化、镀液最佳配方的试验验证3个方面介绍了均匀设计法在Ni-P-MoS2化学复合镀中的应用，并得到了最佳的Ni-P-MoS2化学复合镀液配方。该法应用于化学镀的工艺试验，简便可行。     

添加剂对化学镀铜的影响

研究了亚铁氰化钾和α，α′-联吡啶对陶瓷表面化学镀铜沉积速率、阻抗、镀层晶体结构和外观的影响。加入亚铁氰化钾，铜沉积速率降低，阻抗增大，镀层外观得到改善，镀层晶体呈无序生长；α，α′-联吡啶的加入对铜沉积的抑制更明显，镀层晶体取向为（2，2，0）。     

钛基体化学镀镍及其耐蚀性能

采用化学镀在钛基体上制备Ni-P合金镀层.研究了活化时间、镀液pH值、热处理温度及时间对镀层的影响.用动电位极化曲线法比较镀层的耐均匀腐蚀性能,并用X-射线衍射仪和扫描电子显微镜分别研究镀层结构和表面形貌.结果表明,以HF为主剂的活化液,时间60 s,pH值4.8～5.2的活化工艺以及250 ℃、保温2 h的热处理为最佳工艺.镀层具有较高的耐蚀性能,属于非晶和微晶组成的混晶结构.借助于正交试验,确定了最佳工艺.     

稀土元素在金属电沉积中的应用

综述了稀土元素的性质和在电镀铬、锡、锌、锌－镍合金、镍－铁合金以及在复合镀技术中的应用现状和前景。介绍了水溶液中电沉积稀土金属及其合金的可行性。     

Theoretical studies of displacement deposition of nickel into porous silicon with ultrahigh aspect ratio

A model is developed to address the uniformity of displacement deposition of nickel inside porous silicon with an ultrahigh aspect ratio as high as 200. The nickel distribution is treated as a current distribution issue as in electrodeposition. It is shown that the deposition distribution along the pore depth exhibits a strong dependence on a polarization parameter ξ. High values of ξ correspond to mass transport limitations and lead to non-uniform distributions, whereas small ξ values, representing interfacial reaction control, produce uniform distributions. Non-uniform deposition primarily occurs at an initial stage in which the reaction is dominated by mass transfer. As the deposition process continues, the deposition rate drops to a low value, and the deposition uniformity shifts from Ni²⁺ mass transport limitations to its interfacial reaction control, leading to uniform Ni²⁺ concentration and deposition rate distributions. It is predicted that the non-uniformity at the initial stage could be remedied by increasing the bulk concentration of the nickel ions and decreasing the plating bath pH. In addition, the uniformity of the deposition distribution can be significantly improved by introducing inhibiting additive coumarin to the plating solution.     

The effect of vacuum evaporation plating on phase structure and electrochemical properties of AB5–5 mass% LaMg3 composite alloy

In this paper, Cu, Al and Ni were plated on the AB₅–5 mass% LaMg₃ composite hydrogen storage alloy using a vacuum evaporation plating method. The phase structure and the electrochemical properties were investigated. The X-ray diffraction (XRD) analysis shows that the phase structure is not changed obviously after the plating Cu, Al and Ni on the composites. The electrochemical tests show that maximum discharge capacity, high rate dischargeability (HRD), dischargeability at low temperature and cyclic stability was improved by vacuum evaporation plating Cu, Al and Ni. Maximum of discharge capacity of the AB₅–5 mass% LaMg₃ composite alloy plating Ni can reach 351 mAh/g, which is 3.5% higher than that of the untreated. HRD at I_d = 1200 mA/g of the composite alloy plating Cu is 45.0% of that at 60 mA/g, which is 20.4% higher than the untreated. Discharge capacity of the composite alloy plating Cu at low temperature 233 K is 205 mAh/g, which is 57.3% of that at 298 K, and it is much higher than 36.8% of the untreated composites. The discharge capacity retention of the composite alloy plating Al after 200 cycles is 7.8% higher than the untreated.     

化学镀镍-铜-磷三元合金工艺的研究

为提高化学镀镍－磷合金镀层的性能及获得多种性能的合金镀层以拓宽其应用范围。在化学镀镍－磷合金液中加入硫酸铜制得镍－铜－磷三元合金。研究了镀液中硫酸镍、次磷酸钠、柠檬酸钠、硫酸铜、稳定剂、光亮剂的含量以及pH值和温度等因素对合金镀层的外观、沉积速度及铜含量的影响。通过5％氯化钠溶液和10％硫酸溶液浸泡试验比较了所得镍－铜－磷合金镀层与镍－磷合金镀层以及前人制得的镍－磷合金镀层的耐蚀性，同时比较了上述镀层的其它性能。结果表明，所得镍－铜－磷合金镀层的耐蚀性、外观、结合力、孔隙率、沉积速度、硬度和耐磨性等性能优于镍－磷合金及前人制得的镍－铜－磷合金镀层。     

锌酸盐镀锌层的三价铬蓝色钝化

以外观、醋酸铅点滴实验和中性盐雾实验（NSS）为评价标准，通过正交实验和单因素实验，得到了一种三价铬钝化膜的最佳工艺条件：0．1mol／L CrCl3，0．2mol／L有机羧酸CM，0．24mol／LNaNO3，0．01mol／L Co（NO3）2，8g/LNa2SiO3，pH为1．2，钝化温度为10℃，钝化时间为30s。探讨了配合物CM浓度、硝酸钠浓度、氯化铬浓度、硝酸钴浓度、硅酸钠浓度及钝化液pH、钝化温度、钝化时间的影响。在上述条件下得到的钝化膜呈蓝色，均匀，能通过48h NSS实验。