Contribution of metal vapor mass at periphery part of pulsed arc to electromagnetic force in weld pool

The arc welding has been used in various welding methods because it is inexpensive and high in strength after welding. However, it is a problem that accidents such as collapse of the bridge occur because of the welding defects. The welding of low cost and high productivity is required without the welding defects. The pulsed TIG welding is inexpensive and capable of high‐quality welding. The electromagnetic force contributing to penetration changes because the transient response of arc temperature and iron vapor generated from anode occurs. However, the analysis of pulsed TIG welding with metal vapor has been elucidated only metal vapor concentration near anode with transient phenomenon and heat flux. Thus, the theoretical elucidation of penetration depth with control factor has not been researched. In this paper, the contribution of metal vapor mass at the periphery part of pulsed arc to the electromagnetic force in the weld pool is elucidated. As a result, the iron vapor mass at periphery part decreased with increasing the frequency. The iron vapor was stagnated at axial center within one cycle. The electromagnetic force to the penetration depth direction in weld pool increased at axial center. Therefore, the metal vapor mass at periphery part plays an important role for the electromagnetic force increment at axial center.     

Theoretical study of a thermoelectric-assisted vapor compression cycle for air-source heat pump applications

This paper proposes a thermoelectric-assisted vapor compression cycle (TVCC) for applications in air-source heat pump systems which could enhance the heating capacity of the system. Performances of TVCC are calculated and then compared with that of basic vapor compression cycle (BVCC). The simulation results show that when coefficients of performance (COPs) of the two cycles are almost equal, the TVCC under maximum COP condition of the thermoelectric modules still performs better than BVCC by 13.0% in heating capacity through selecting the appropriate intermediate temperature. In addition, the TVCC can also achieve an improvement of 16.4%–21.7% in both the heating COP and capacity when compared with the BVCC with an assistant electric heater that is provided with the equivalent power input of thermoelectric heat exchanger. Thus, the TVCC could be beneficial to the applications in small heat pumps if there is always need for auxiliary electric heat.     

宁夏宁东供水工程主机设备形式参数选择与国际招标

宁东供水工程供水水泵共有卧式和立式离心泵2种方案可供选择,也是工程论证时争论的焦点,经综合比较及主机设备的国际招标,最终确定了奥地利安德里兹公司的卧式双吸中开式离心泵为宁东供水工程的供水水泵。     

电路电磁兼容建模与仿真

提出了对暴露在任意外场中的传输线进行时频分析的新方法，这种方法非常稳定，它能够与任意的传输线模型和电路仿真方法兼容，并且使用这种方法得到的仿真值和实际值之间的差别小于1％。     

迷宫螺旋泵和密封工作特性研究

介绍了一种实测迷宫螺旋泵和密封工作特性的实验方法,通过该方法可以测得迷宫螺旋泵的泵送特性曲线、迷宫螺旋端面组合密封的最大密封压力以及端面开启的开始转速,具有一定的实用价值。     

无油分子泵机组的组装

介绍了将ALCATEL公司生产的一台ATPl00涡轮分子泵、一台MDP50ll牵引分子泵及一台VRC公司生产的lBy6型干泵组装成无油分子泵机组的过程。文中给出了泵间配合的计算、机组方案的设计、连接管路、仪器支架的设计及选择。本机组所采取的设计方案使三个泵都最大限度地发挥了优点避免了缺陷，较好地满足了使用要求，为今后选购单泵和组装无油分子泵机组提供了可靠的理论和实验依据。     

双级染料激光放大器泵浦能量分配的数值研究

用染料激光放大器的横向稳态泵浦理论，对不同的入射光能量选择不同的增益计算方法，研究了双级染料放大器的泵浦能量分配比例、泵浦光总能量和信号光能量大小对激光增益的影响。计算结果表明，对于其他参数确定的放大系统，存在着最佳的泵浦能量分配比例，可获得最大增益输出。通过自编程序的计算，可方便地找出特定系统泵浦能量分配比例的最佳值。     

射孔枪+内置式压力计托筒+水力泵新三联作试油(测试)工艺技术在大港油田研制与应用

该工艺技术是在原三联作(TCP+MFE+JET)基础上,根据大港油田勘探试油(测试)的需要,研制开发出的又一新技术,与原三联作相比,一趟管柱不但完成求产、测压、泵排工作,而且还能进行酸化等措施,提高了资料品质,减少了作业成本。经过6井次现场应用,全部达到了设计要求,取得了工艺、资料、成本、速度的较大进步,具有较高推广应用价值。     

医用激光治疗机的触摸屏控制系统设计

介绍了医用红宝石激光器触摸屏控制系统的基本结构，分析了医用红宝石激光器中主要电磁干扰（EMI）的产生机制，提出了具体的电磁兼容（EMC）技术措施并得到实验验证。     

高含沙水深井泵站的综合治理

对攀钢动力厂深井泵站自投产以来出现的主要问题及其解决方案，方法进行了分析和论述。