Complex study of protective Cr3C2–NiAl coatings deposited by vacuum electro-spark alloying,pulsed cathodic arc evaporation,magnetron sputtering,and hybrid technology

Coatings were obtained by vacuum electro-spark alloying (VESA), pulsed cathodic arc evaporation (PCAE), magnetron sputtering (MS) techniques and VESA-PCAE-MS hybrid technology using Cr₃C₂–NiAl electrodes. The structure of the coatings was analyzed using scanning and transmission electron microscopy, X-ray diffraction and energy-dispersive spectroscopy. Mechanical properties were determined by nanoindentation, while tribological properties were assessed using pin-on-disk tribometer. Corrosion resistance was estimated by voltammetry in 1 N H₂SO₄ and 3.5%NaCl solutions. Oxidation resistance tests were performed at 800°С in air. The VESA coating had the highest thickness, low friction coefficient and high wear resistance. PCAE coating demonstrated the highest hardness (24 GPa) and elastic recovery (59%), oxidation resistance and superior corrosion resistance both in 1 N H₂SO₄ (i_corr = 70 μА/cm²) and 3.5%NaCl (i_corr = 0.74 μА/cm²) solutions. The MS coating had average mechanical properties and low corrosion current density (71 μА/cm²) in 1 N H₂SO₄. Deposition of coatings using VESA-PCAE-MS hybrid technology led to an increase in corrosion and oxidation resistance at least by 1.5 times in comparison with the VESA coating.     

Chromium evaporation and oxidation characteristics of alumina-forming austenitic stainless steels for balance of plant applications in solid oxide fuel cells

The chromium (Cr) evaporation behavior of several different types of iron (Fe)-based AFA alloys and benchmark Cr₂O₃-forming Fe-based 310 and Ni-based 625 alloys was investigated for 500 h exposures at 800 °C to 900 °C in air with 10% H₂O. The Cr evaporation rates from alumina-forming austenitic (AFA) alloys were ~5 to 35 times lower than that of the Cr₂O₃-forming alloys depending on alloy and temperature. The Cr evaporation behavior was correlated with extensive characterization of the chemistry and microstructure of the oxide scales, which also revealed a degree of quartz tube Si contamination during the test. Long-term oxidation kinetics were also assessed at 800 to 1000 °C for up to 10,000 h in air with 10% H₂O to provide further guidance for SOFC BOP component alloy selection.     

真空制盐蒸发结晶器的设计与实践

真空蒸发制盐外热式强制逆循环轴向出料蒸发结晶器，经多个厂家生产应用实践证明是成功的，具有生命力的。这种新型结构，作为一项新技术新设备应加强研究，总结提高，推广应用。不断完善。文章从流体力学、结晶机理角度要求，到具体工程设计参数和材质选用。论述了该罐的特点。     

Minimizing sample evaporation in the environmental scanning electron microscope

The ElectroScan environmental scanning electron microscope (ESEM) enables wet samples to be observed by eliminating air but allowing water vapour into the sample chamber. However, evaporation from, and condensation on, the sample may occur during the pumpdown sequence used to reach this state, which means that the sample may not be in its natural state when viewed if due care is not taken. In this paper, the pumping system of the ESEM is described mathematically and expressions are derived for the evaporation and condensation. This treatment is then used to calculate the optimum pumpdown sequence. The importance of using the optimized procedure is illustrated by micrographs of fat emulsions.     

硫铁矿沸腾炉内蒸发管组防磨技术的探讨

为减少磨损,沸腾炉内蒸发管采用加焊半圆形钢板防磨.探讨了沸腾炉内蒸发管加焊半圆形钢板的防磨机理.实际使用情况表明,加焊半圆形钢板防磨大大降低了维修费用,显著提高了防磨效果.     

Evaporation and Evolution of Suspended Solution Droplets at Atmospheric and Reduced Pressures

Thermal history and solute precipitation behavior of suspended solution droplets of sodium chloride (NaCl), magnesium sulphate (MgSO₄), and zirconium hydroxychloride (ZrO(OH)Cl) evaporating at atmospheric and reduced pressures are studied. Experimental measurements on the variation of droplet diameter, solution concentration, and temperature during the evaporation period are presented and discussed. The results of solute precipitation behavior in solution droplets observed under an optical microscope are displayed and discussed. Results indicate that reducing the pressure (∼ 33 kPa) results in a change in the solution droplet evaporation rate, but the thermal histories of a particular solution droplet are similar at the atmospheric and reduced pressures. At atmospheric and reduced pressures used in this study, the d² law for solution droplets is valid at early stages of the evaporation and before the solute precipitation initiates. Drying of MgSO₄ and ZrO(OH)Cl solution droplets results in the formation of spherical particles, whereas drying of spherical NaCl solution droplets results in the formation of cubic particles.     

Finite Element Analysis of a Moving Boundary Value Problem

A finite element formulation and the solution of a set of nonlinear coupled heat and mass transfer equations for a two-phase system with a moving evaporation interface is presented. The interface condition takes into account the moisture transfer balance at the moving boundary. The finite element results were compared with existing results for a single phase system for model validation. In the two-phase system, the movement of evaporation front has an appreciable effect on the temperature and moisture distribution inside the porous medium during drying. The effect of the nondimensional heat of vapourization parameter γ on the evaporation front, temperature and moisture distribution in porous medium was studied. The higher the value of γ, the slower is the movement of the evaporation front. The temperature decreased and the moisture content increased as the nondimensional vapourization parameter γ increased. This model has potential applications in studying the heat and mass transfer characteristics in food and biomaterials.     

Evaluation of Textile Bobbins Drying Processes: Experimental and Modelling Studies

Drying of textile bobbins was carried out on two kinds of laboratory-scale dryers: in a cross circulation drying rig, atmospheric pressure heating air is used, while in the through circulation drying apparatus, the heating air is pressurized before the drying process takes place. In both cases, a bobbin was fitted with seven thermocouples, placed in a plane normal to the bobbin axis but at different radial distances, in order to provide temperature data during the drying process. In cross circulation drying, plots of temperature against time indicated the presence of two moving fronts, one starting from inside the bobbin, another from the outside, while in through circulation drying, similar plots showed the presence of an evaporation front, moving from inside the bobbin to the outside. In both canes, numerical models were developed to simulate the drying processes.     

纳米ZnO薄膜制备及液态源掺杂

用真空蒸发法在玻璃和单晶硅片 (10 0 )上制备Zn薄膜 ,然后对Zn薄膜进行氧化、热处理获得纳米ZnO薄膜。对在硅片上制备的Zn薄膜一次性进行高温掺杂、氧化获得纳米ZnO∶P和ZnO∶B薄膜。研究不同氧化、掺杂温度和时间对薄膜结构、电学性能的影响。结果表明 :氧化温度和时间对ZnO薄膜结构影响较大 ,液态源掺P可明显改善纳米ZnO薄膜的导电性能、结构特性和化学组分