注硼中子寿命测井注硼工艺优化设计

注硼中子寿命测井是一项水淹层测井新技术 ,对老油田的产层分析评价、剩余油含量估算等方面发挥了重要的作用。但测井施工时 ,往往由于注硼工艺不当导致硼酸的渗吸量难以准确反映地层可动水的含量 ,从而产生解释上的困难和误区。在渗流与扩散理论相结合的基础上 ,结合华北油田的施工实践 ,介绍了确定注硼管柱、硼酸用量、注硼压力以及硼酸扩散时间的基本原则和实际经验 ,为工艺的优化设计提供了一些方法与思路     

提高连续油管使用寿命的方法

从采用软件跟踪疲劳寿命 ,截断法 ,变径连续油管 ,反转使用连续油管 ,防止连续油管损伤 ,合理配置设备 6个方面讨论了控制管串疲劳 ,提高连续油管使用寿命的方法 ,并得出结论 :控制管串疲劳的方法中 ,最有效的方法是实际作业截断法。指出要尽量减少连续油管在带内压下工作 ,也要研究开发降阻性能好的工作液 ,以延长连续油管使用寿命、降低作业风险。     

Effect of doping polyacrylic acid with some dopants as studied by different techniques

The molecular weight of polyacrylic acid (PAA) was determined by a viscometric method using NaNO₃ as solvent at 30°C. The specific electric conductivities (σ) of PAA as well as PAA doped with carbon black (CB), chromium oxide (Cr₂O₃), and cupferron with different concentrations (from 0.25 to 1 wt %) were measured at a temperature range 360–400 K. IR spectra of some polymers were determined and it was shown that when PAA was doped with 0.5 wt % CB, a C? O? C band appeared at 775–875 cm^?1. The positron annihilation lifetime (PAL) spectra in PAA doped with the above‐mentioned dopants were measured as a function of their concentrations. It was observed that the short lifetime intensity I₁ decreased, whereas the intermediate lifetime intensity I₂, which is related to the conductivity of the material, increased with increasing the wt % of Cr₂O₃ and cupferron as well as at low concentrations of CB. These results are discussed in terms of the conducting island model. It was found that there were distinct positive relationships between σ and I₂. © 2002 John Wiley & Sons, Inc. J Appl Polym Sci 84: 877–883, 2002; DOI 10.1002/app.10381     

Crack growth in aluminium alloy sheet material under flight-simulation loading

Crack propagation tests were carried out on 2024-T3 sheet specimens to study the effects of omitting low-amplitude cycles from the gust-dominated TWIST load sequence (MiniTWIST) and the removal of small load ranges from the manoeuvre-dominated FALSTAFF load sequence (short FALSTAFF). In other tests high-amplitude loads of TWIST and MiniTWIST were truncated at different levels. The results are compared with data from similar test programmes, including crack initiation. Attention is paid to unstationary crack growth retardation and a transient retardation during initial crack growth started by an artificial crack.     

延长分米波电视发射管使用寿命的探讨（上）

文章从原理上讨论了影响分米波电视发射管寿命的若干因素。并提出了若干延长寿命的建议：（１）正确的灯丝加热方法是行之有效的措施，经验证明：过分强调降低灯丝电压往往得到相反的效果。（２）必须有良好的冷却方式。（３）通过对帘栅电路的分析，说明对此电路必须作很好的处理以消除故障和防止寄生振荡。     

Microstructure-related fracture toughness and fatigue crack growth behaviour in toughened, anhydride-cured epoxy resins

Fracture toughness and fatigue crack propagation (FCP) of plain and modified anhydride-cured epoxy resin (EP) were studied at ambient temperature. Liquid carboxyl-terminated acrylonitrile-butadiene (CTBN) and silicon (SI) rubber dispersions were used as tougheners for the EP. The morphology of the modified EP was characterized by dynamic mechanical analysis (DMA) and by scanning electron microscopy (SEM). The fracture toughness, K_c, of the compositions decreased with increasing deformation rate. K_c of the EP was slightly improved by CTBN addition and practically unaffected by incorporation of the SI dispersion when tests were performed at low cross-head speed, v. Both modifiers improved K_c at high v, and also the resistance to FCP, by shifting the curves to higher stress intensity factor ranges, ΔK, by comparison with the plain EP. It was established that both fracture and fatigue performance rely on the compliance, J_R, at the rubbery plateau, and thus on the apparent molecular mass between crosslinks, M_c. The failure mechanisms were less dependent upon the loading mode (fracture, fatigue), but differed basically for the various modifiers. Rubber-induced cavitation and shear yielding of the EP were dominant for CTBN, whereas crack bifurcation and branching controlled the cracking in SI-modified EP. The simultaneous use of both modifiers resulted in a synergistic effect for both the fracture toughness at high deformation rate and the FCP behavior.     

Rolling contact fatigue behavior of sintered and hardened steels

Powder-metal-processed bearings and gears are finding increasing application because of their economical and technical advantages. The residual pores from the sintering operatives act as lubricant pockets and dampen sound and vibration. However, porosity also decreases the mechanical strength and reduces the life of components fabricated by powder processing relative to similar wrought components. The rolling contact fatigue behavior of sintered and heat treated steel rollers was investigated using a fatigue test machine designed and fabricated for that purpose. The powder-metal-processed and the wrought steel rollers that were tested had similar composition and hardness and were mated against wrought steel rollers of high hardness. The contact stress versus number of cycles to failure data showed that the wrought steel had a very high endurance limit under rolling contact fatigue compared to the sintered steels investigated. Rolling contact fatigue behavior was found to depend on the porosity present in the material. Large surface peeling failures and pitting type fatigue failures were observed in the sintered and hardened steels, while only pitting type failures were observed in the wrought steels     

Thermal shock and thermal fatigue study of ceramic materials on a newly developed ascending thermal shock test equipment

A test equipment was designed to study thermal shock and thermal fatigue of ceramic materials subjected to fast heating (ascending). The equipment was designed to generate thermal stress in a test specimen by heating one surface of it by an oxy-hydrogen flame while cooling the opposite surface. The sample cracked when thermal stress exceeded its mechanical strength. The in situ crack formation was detected by an acoustic emission system coupled to the set up. The hot zone temperature was measured by an infra red pyrometer. The equipment was also designed to run thermal fatigue test cycles in automatic mode between two selected temperatures. The temperature and thermal stress distribution in the test specimen were modelled using finite element software. The effect of temperature distribution of the top and bottom surfaces on thermal stresses was studied. It was observed that the thermal stress is very sensitive to the temperature distribution on the top surface and maximum near the periphery of the top surface. This was in agreement with the experimental results in which the cracks were originated from the periphery of top surface. It was also observed that the failure temperature was higher for thicker samples.     

国产核电厂蒸汽发生器下封头接管区模拟装置承受循环载荷能力的试验

国产核电厂蒸汽发生器下封头群孔接管区具有应力分布复杂、焊接施工条件差的特点。为考核其承受循环载荷的能力，设计制造了与实物相似的模拟试验装置，根据核电厂运行寿命期内的载荷特点，确定了模拟试验装置的试验载荷与试验循环数。循环加载试验的结果表明，蒸汽发生器下封头群孔接管区承受循环载荷的能力在寿命期内是符合要求的。