避免发生芯片裂纹的倒装片BGA技术概述

介绍了把断裂力学法应用于倒装片BGA的设计方法。概述了一些关键的材料特性和封装尺寸对倒装片BGA芯片裂纹的影响作用，从而断定基板厚度和芯片厚度是倒装片BGA芯片发生裂纹的两个最重要的因素。     

漂白麦草浆细杂组份对阳离子淀粉吸附的影响

本文研究了漂白麦草浆中细杂组份(通过100目,其中大部分是杂细胞,如薄壁细胞,表皮细胞)对阳离子淀粉吸附的影响。 实验表明,漂白麦草浆中细杂组份的比表面积明显大于纤维组份(保留在100目以上)的比表面积。阳离子淀粉优先吸附在比表面积大的细杂组份上。纤维组份的吸附能力受化学环境的影响较细杂组份更为敏感。     

热压细晶高功率微波铁氧体

利用热压工艺制备出了细晶粒（２μｍ）ＹＩＧ铁氧体材料,测量了其微波性能,结果表明,细晶粒铁氧体的自旋波线宽ΔＨｋ显著提高,其ΔＨｋ与晶粒尺寸有ａ０＾－１．７的相依关系。同时,分析讨论了细晶粒铁氧体铁磁共振线宽ΔＨ的致宽因素。     

Wettability of micron/submicron-sized particles in oilsands bitumen characterized by suspension turbidity

Determination of the wettability of micron/sub-micron sized particles remains a great challenge. The present work proposes a new approach to evaluate the particle wettability by measuring the turbidity of particle suspension. The fine solid samples with varying wettability were prepared by hydrothermal treatment of oilsands bitumen at different temperatures. The turbidity of particle-in-toluene suspension was determined and correlated to the particle surface chemical composition, i.e., C/(Al?+?Si). A good linear relationship was observed between particle wettability and suspension turbidity. The results suggest suspension turbidity can be used to characterize the wettability of organically-modified fine solids in oilsands bitumen.     

超细活性氧化锌在轿车子午线轮胎胎面胶中的应用

对超细活性氧化锌在轿车子一轮胎胎面胶中的活尼效果分两组配方做了实验。结果表明,超细活性氧化锌由于活性高、等效用量小,与普通氧化锌相比有加快硫化速度的效果,并能改善胶料的加工性能,提高硫化胶的扯断永久变形、耐老化性和耐疲劳性能;超细活性氧化锌胶料加入活性碳酸钙后,能胶料生产成本,提高经济效益。     

HDI精细线路制作工艺的探讨

随着HDI制作工艺的飞速发展,不同品种类型HDI的制作决定着其本身所选用的积层方式和线路制作工艺。本文通过对各种HDI线路制作工艺的对比分析,探讨了目前国内各HDI生产厂家普遍采用的线路制作工艺与品质特性及其未来发展趋势。     

Statistical Characterization of Open Failures in the Fine-Pitch COG Interconnection

Chip-on-glass (COG) interconnection using anisotropic conductive film (ACF) is susceptible to open failures. Open failures can be induced by the absence of conductive particles or an insufficient contact. Experimental results as well as statistical approaches were used to understand the conditions for open failures in COG bonding. The binomial distribution was used to predict the probability of the open failure due to the deficiency of conductive particles. The probability of an open failure decreased with increasing bump area and decreasing particle size. The bump height variation was also an important factor that affected the probability of the open failure together with the bump-to-electrode gap and the particle size. The variation in bump height should be minimized to avoid open failures in fine-pitch applications where a smaller particle size is required.     

Cu－Zn－Al合金贝氏体的三个生长阶段及其精细结构研究

利用透射镜研究了Ｃｕ－Ｚｎ－Ａｌ合金贝氏体ａ＿１相在相变过程中的精细结构变化，发现贝氏体的生长经历三个阶段：初生态、中间态和退化态。初生贝氏体内不含层错亚结构，ａ＿１依台阶机制长大到一定程度后，内部出现层错；随转变进一步进行，ａ＿１内的层错结构逐渐消失，发生“过退火”，最终向平衡相转变。     

型煤发展的回顾与展望

煤炭科学研究总院建院以来型煤研究工作的进展状况、主要成果,并对几项工业型煤技术进行了概述和评价,还对今后型煤研究方向提出了建议。     

A universal roll‐to‐roll slot‐die coating approach towards high‐efficiency organic photovoltaics

This work develops a combinational use of solvent additive and in‐line drying oven on the flexible organic photovoltaics to improve large‐area roll‐to‐roll (R2R) slot‐die coating process. Herein, addition of 1,8‐diiodooctane (DIO) in the photoactive layer is conducted to yield a performance of 3.05% based on the blending of poly(3‐hexylthiophene) (P3HT) and [6,6]‐phenyl C₆₁‐butyric acid methyl ester (PC₆₁BM), and a very promising device performance of 7.32% based on the blending of poly[[4,8‐bis[(2‐ethylhexyl)oxy] benzo[1,2‐b:4,5‐b’] dithiophene‐2,6‐diyl] [3‐fluoro‐2‐[(2‐ethylhexyl)carbonyl]thieno[3,4‐b]thiophenediyl]] (PTB7) and [6,6]‐phenyl C₇₁‐butyric acid methyl ester (PC₇₁BM). Based on this R2R slot‐die coating approach for various polymers, we demonstrate the high‐performance result with respect to the up‐scaling from small high‐PCE cell to large‐area module. This present study provides a route for fabricating a low‐cost, large‐area, and environmental‐friendly flexible organic photovoltaics.