Flammability characteristics at applied heat flux levels up to 200 kW/m2

This paper documents the first of the two interrelated studies that were conducted to more fundamentally understand the scalability of flame heat flux, the motivation being that it has been reported that flame heat flux back to the burning surface in bench‐scale experiments is not the same as for large‐scale fires. The key aspect was the use of real scale applied heat flux up to 200kW/m² which is well beyond that typically considered in contemporary testing. The main conclusions are that decomposition kinetics needs to be included in the study of ignition and the energy balance for steady burning is too simplistic to represent the physics occurring. An unexpected non‐linear trend is observed in the typical plotting methods currently used in fire protection engineering for ignition and mass loss flux data for several materials tested and this non‐linearity is a true material response. Using measured temperature profiles in the condensed phase shows that viewing ignition as an inert material process is inaccurate at predicting the surface temperature at higher heat fluxes. The steady burning temperature profiles appear to be invariant with applied heat flux. This possible inaccuracy was investigated by obtaining the heat of gasification via the ‘typical technique’ using the mass loss flux data and comparing it to the commonly considered ‘fundamental’ value obtained from differential scanning calorimetry measurements. This comparison suggests that the ‘typical technique’ energy balance is too simplified to represent the physics occurring for any range of applied heat flux. Observed bubbling and melting phenomena provide a possible direction of study. Copyright © 2007 John Wiley & Sons, Ltd.     

安钢高线粗中轧机导卫设计特点

介绍了安钢自行设计的高线粗中轧机导卫装置的设计原则和特点。     

Si相的析出状态对Al—Si合金性能的影响

控制Si相的析出状态,会对Al-Si(1wt％)合金的性能产生不同的影响。本文阐述通过不同的热处理工艺改变了Al-Si(1wt％)合金的机械、物理性能,获得了高形变强化率、高塑性变形能力、高拉伸强度的工艺,还讨论了具有上述高拉伸强度的微细丝在半导体器件应用中所具有的优越性。     

连续式棒线材轧机孔型系统的选择

论述了连续式棒线材轧机孔型系统的种类和特点，介绍了粗轧机组和中轧机组孔型系统的选择原则和方法。     

大小样品在液氮中的淬冷沸腾换热比较研究

分析了大小样品在液氮中的淬冷沸腾换热特性。大小样品的淬冷沸腾换热有着明显的差别，小样品的热流密度比大样品的明显高得多。小样品的淬冷沸腾有一起始段，其温降高达６０Ｋ。从实验结果还可以看到，小样品的Ｌｅｉｄｅｎｆｒｏｓｔ点和临界热流点对应的壁面过热度明显比大样品的高。最后还分析了样品直径对临界热流密度的影响。     

导线物证的扫描电镜及能谱鉴定方法

对导线物证同一性的鉴定，可先用X射线能谱仪快速确定物证为同一物的必要条件，再用扫描电镜对物证的特征条纹或金相组织进行最后判定。该方法简便，可靠。     

A Study of Surface Deformation during Wire‐Rod Rolling of High Speed Steels using Experimental and Computational Techniques

The evolution of surface defects during shape rolling of high‐speed steel billets is studied using longitudinal surface defects prepared by machining and welding. The reduction of the defects during rolling in a production mill is compared to the total area reduction of the billets. Samples are collected after pass 4, 6, 8, 14, 19 and the final pass, 28, representing the finished 5.5mm wire. By inspecting the cross sections, the rotation of the billets from pass to pass is evaluated. Results from FE simulations on solid billets are compared to the experimental results. Generally, simulations predict less reduction than observed experimentally. In most cases cracks reduce most effectively followed by carbon steel welds and stainless steel welds.     

Effect of site-selective substitution in bulk superconducting Tl2Ba2CaCu2O8

Magnetization measurements were carried out on bulk Tl₂Ba₂CaCu₂O₈ (referred to as Tl-2212) and on various site-selective substituted Tl-2212 samples. At 5K between 0 and 4.5 T, the 5 at. % Mg-doped Tl-2212 (Tl,Mg-2212) samples displayed enhanced pinning as demonstrated by a field dependent increase of the magnetic critical-current density J_c by 18 to 25 percent over that of pristine Tl-2212. Excess Mg (10–15 at. %), however, is deleterious. Rietveld refinement of the x-ray diffraction pattern showed Mg on the Tl sites. Auger electron spectroscopy analysis showed part of the Mg on grain boundaries. The flux-creep activation energies are higher for flux expulsion than for flux penetration in both Tl-2212 and Tl,Mg-2212 samples; the latter displays higher individual values. Our results demonstrate an increase in the number density of flux lines as a result of increased density of atomic-size-structural, defects by Mg (5 at. %) doping. In the Tl_2−yBa₂(Ca_1−zY_z)Cu₂O_8−x(z=0–0.3; single phase; x and y represent oxygen and thallium vacancies) system also studied, the T_c decreases as z increases. At z=0.3, the sample becomes an antiferromagnetic semiconductor.     

管杆漏磁探伤现场应用中的问题及对策

阐述了漏磁探伤漏磁场沿管、杆径向的分布特征 ,分析了影响探伤装置漏磁检测准确性的 4个因素 ,验证了信号提离距离的变化对传感器和探伤装置灵敏度的影响。针对在用的大多数浮动式传感器固定机构存在的两个严重缺点 ,提出采用自定位传感器固定机构 ,可消除机械装置对传感器灵敏度的影响。提出了一套标定和校验检测装置的方法 ,以保证探伤仪器的检测灵敏度始终恒定 ,提高检测结果的准确性和可靠性。     

斜井提升钢丝绳磨损“失效树”分析

介绍了引起斜井提升钢丝绳失效的各种因素 ,并建立“失效树” ,为煤矿生产中判断其失效原因及预防提供可靠依据。