塑木复合材料市场和发泡塑木复合材料

综述了塑木复合材料性能、应用、市场及其预测和发泡塑木复合材料技术、发展动向,重点介绍了发泡塑木复合材料的优点、发泡剂、基础树脂、木纤维和工业化产品。     

阳极氧化对压铸铝合金电解着黑色工艺的影响

选择压铸铝合金ADC12为研究对象,确定黑色为着色系,在确定的电解着色工艺下,重点探讨溶液种类、浓度和温度等阳极氧化工艺参数对黑色膜完整性、色泽度的影响。通过系列试验,优选工艺参数如下：以水磨、抛光、除油为前处理;在直流电压20V下,于20％H2SO4溶液中进行阳极氧化,温度为40℃。反应时间为40min,可获得黑度系数达0．9且膜色均匀的染色膜层。结合基体显微组织分析,认为要改善膜层着色效果,宜先通过有效的熔体处理,改善基体组织形态。     

泡沫混凝土配合比的设计

在研究泡沫混凝土各种原材料性能及大量实验和中试生产实践基础上,运用数理统计归纳分析,设计出既能满足泡沫混凝土干密度、导热率、强度、浇筑稳定性等技术要求,又经济合理、易于操作的各种原材料配合比,达到控制泡沫混凝土导热系数和抗压强度的目的,进而指导泡沫混凝土生产工艺过程,确保产品质量.     

Light metal compound casting

‘Compound casting’simplifies joining processes by directly casting a metallic melt onto a solid metal substrate. A continuously metallurgic transition is very important for industrial applications, such as joint structures of spaceframe constructions in transport industry. In this project, ‘compound casting’ of light metals is investigated, aiming at weight-saving. The substrate used is a wrought aluminium alloy of type AA5xxx, containing magnesium as main alloying element. The melts are aluminium alloys, containing various alloying elements (Cu, Si, Zn), and magnesium. By replacing the natural oxygen layer with a zinc layer, the inherent wetting difficulties were avoided, and compounds with flawless interfaces were successfully produced (no contraction defects, cracks or oxides). Electron microscopy and EDX investigations as well as optical micrographs of the interfacial areas revealed their continu- ously metallic constitution. Diffusion of alloying elements leads to heat-treatable microstructures in the vicinity of the joining interfaces in Al-Al couples. This permits significant variability of mechanical properties. Without significantly cutting down on wettability, the formation of low-melting intermetallic phases (Al3Mg2 and Al12Mg17 IMPs) at the interface of Al-Mg couples was avoided by applying a protective coating to the substrate.     

铝合金中锌、铁的快速测定--原子吸收分光光度法

样品以盐酸溶解，加入过氧化氢助溶，蒸至近干．加入1 1盐酸提取，移入100mL容量瓶中，分取部分溶液于50mL容量瓶中，调整盐酸酸度为5％，用水稀至刻度，摇匀后，以空气-乙炔火焰水相直接测定锌和铁。为了消除大量基体元素的影响，在标准系列中加入相当量的铝。此方法快捷、简便，亦可用于锰、镁、铜、铅、镍的测定。     

MnO_(x/γ)-Al_2O_3催化加氢合成3,5-二甲氧基苯甲醛

α将3,5-二羟基苯甲酸与硫酸二甲酯在碱性条件下反应生成3,5-二甲氧基苯甲酸甲酯,然后在高压下以MnOx/y-Al2O3为催化剂催化加氢得到3,5-二甲氧基苯甲醛。总收率81.7％。催化剂采用共沉淀法制备,Mn载量wMn=15.3％。     

氮化铝纳米粉末的氧化特性研究

采用直流电弧等离子体蒸发－凝聚法制备了高纯氮化铝（ＡＩＮ）纳米粉末。粉末的平均晶粒度为５０ｎｍ，纯度大于９８％。借助Ｘ射线光电子能谱、化学分析和差热失重等测试手段，探索了ＡＩＮ纳米粉末的表面化学组成和氧化特性。研究结果表明，ＡＩＮ纳米粉末易吸湿氧化，大大降低了其纯度。ＡＩＮ纳米粉末表面的氧是以两种状态即物理吸附态和化合态存在。     

Effects of silicone oil and polymeric modifiers on the mechanical properties of highly filled LLDPE

The effects of coupling agents, silicone oil, and three types of polymeric modifiers on the mechanical properties of linear low density polyethylene (LLDPE) composites highly filled with aluminium hydroxide [Al(OH)₃] were studied. Polymeric modifiers that contain polar groups, such as silane‐grafted polyethylene (Si‐g‐PE) and acrylic‐acid‐grafted ethylene‐vinyl acetate copolymer (AA‐g‐EVA), improve the mechanical properties dramatically, while nonpolar modifiers improve them to some extent. When Al(OH)₃ was treated using a titanate coupling agent, the silicone oil increased the impact strength and elongation at break of the LLDPE/Al(OH)₃ composites. Introduction of a polymeric modifier containing polar groups destroys the beneficial effects of silicone oil on film mechanical properties, while the introduction of a nonpolar elastomeric polymeric modifier retains the high impact strength and elongation at break. SEM analyses provide the indirect evidence of the encapsulation of silicone oil around the filler. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 121–128, 2002     

The Effect of Temperature on the Strength of Adhesively-Bonded Composite-Aluminium Joints

Different materials have different coefficients of thermal expansion, which is a measure of the change in length for a given change in temperature. When different materials are combined structurally, as in a bonded joint, a temperature change leads to stresses being set up. These stresses are present even in an unloaded joint which has been cured at say 150°C and cooled to room temperature. Further stresses result from operations at even lower temperatures.

In addition to temperature-induced stresses, account also has to be taken of changes in adhesive properties. Low temperatures cause the adhesive to become more brittle (reduced strain to failure), while high temperatures cause the adhesive to become more ductile, but make it less strong and more liable to creep.

Theoretical predictions are made of the strength of a series of aluminium/CFRP joints using three different adhesives at 20°C and 55°C. Various failure criteria are used to show good correlation with experimental results.     

Refinement mechanism of in-situ Al4C3 particles on AZ91 magnesium alloys

The effects of SrCO3 on the microstructure of AZ91 magnesium alloy were investigated by OM, SEM, EDS, XRD and DTA analyses. The results show that AZ91 magnesium alloy with 1.0% SrCO3 addition has the best refining effect at 730 ℃ for 20 min, the average size of the α-Mg grain in AZ91 matrix alloy is reduced from about 91 μm to 58 μm, with reduction of about 36%. Based on the analysis results of EDS, binding energy, and Gibbs free energy, it is evident that the grain is refined because of the generation of A14 C3 particles which can be used as the crystal nucleus of the magnesium alloy when SrCO 3 is added. Owing to the generation of A14C3 in AZ91 magnesium alloy, the grain boundary is pined and the grain growth is inhibited. In the accession to the Al4C3, small subcooling temperature difference leads to the formation of fine grain microstructure in alloy melt. Fine grain microstructure in AZ91 alloy melt with the addition of SrCO3 can be obtained on the condition of lower undercooling temperature according to the DTA analysis results.