盘磨机磨盘间隙在线测量技术研究

介绍了国内外对于磨浆机磨盘间隙测量的研究现状,以及磨浆机磨盘间隙在线测量的改进方法,进一步探讨了电涡流传感器在磨浆机上齿盘边界特性、齿盘变转速响应特性、进退盘响应特性、齿盘的静动态响应性能、输出特性等最佳特性曲线拟合方程。优化了电涡流传感器结合超声波测厚仪对磨浆机磨盘间隙的实时在线测量方案。传感器安装与磨片边缘的距离大于2 mm、动盘外缘线速度大于360 m/min时,电压值稳定,进退盘响应及静动态输出特性变化总体趋于一致,最佳特性拟合曲线方程线性系数大于0.99。     

再谈制作高温电阻应变式称重传感器的若干问题(1)

为了提高高温称重传感器的性能,本文对应变片、应变片装置及高温称重传感器在实际应用环境中的温度传递作深入介绍,以利于研究人员能更深入、全面地了解高温称重传感器及高温环境下称量技术的特点。     

感压膜片预张力对电容薄膜真空规输出特性的影响

电容薄膜真空规中感压膜片在安装时通常须先施加预张力,再固定.为研究感压膜片预张力对电容薄膜真空规输出特性的影响,以现有电容薄膜真空规为对象,基于COMSOL Multiphysics软件,建立有限元模型,得到了不同预张力下输出电容的仿真解,并与理论计算结果进行了比较,分析了预张力对输出电容的影响.同时分析了真空规线性度...     

轻钢龙骨结构体系受力性能的比较分析

介绍了轻钢龙骨体系的主要特点,通过对某工程分别采用轻钢龙骨结构和混凝土结构等其他结构方案的对比分析,表明了该结构体系在我国大多数地区建造是切实可行的,符合现行相关规范的要求.     

液体分布器检测专用工具在汽提塔中的应用

介绍一种液体分布器检测专用工具的原理,该工具应用在尿素汽提塔后,保证了汽提塔液体分布效果,对汽提塔设备保护和节省汽耗起到关键作用.     

某轻钢厂房倒塌事故分析

通过对某轻钢厂房在一次大雪中倒塌事故的检测鉴定,对该钢结构厂房的倒塌事故进行全面分析,并对当前钢结构设计施工中存在的问题提出建议.     

方形角尺的测量及不确定度评定

介绍了方形角尺垂直度误差的测量方法、测量中的关键问题以及测量不确定度分析.     

Length of small gauge zone between cylinder and flat of a card

The length of small gauge zone (SGZ) between cylinder and flat of a card was studied mathematically. A formula to calculate the length was derived with geometry and calculus methods, by which the abscissa of the point at which the flat–cylinder gauge was minimal was obtained. The effect of heel–toe difference (HTD), cylinder radius, flat setover, minimum flat–cylinder gauge, as well as the difference between outlet gauge and minimum flat–cylinder gauge on the length of SGZ was discussed, respectively. It is concluded that a smaller cylinder radius, smaller HTD and a longer flat setover will help to lengthen SGZ. Given an appropriate value of the difference between the outlet gauge and the minimum gauge, δ, a longer SGZ will be beneficial to improving the carding intensity. But the influence of δ and the minimum flat–cylinder gauge on the length of SGZ can be ignored. The conclusion is of some theoretical value for manufacturers of textile accessories or machinery to accurately choose parameters such as cylinder radius, HTD and setover in production.     

Identification of bearing load by three section strain gauge method: Theoretical and experimental research

Reasonable bearing load distribution is important for the safe and reliable operation of rotating machinery. However, it is difficult to measure bearing load in field. This paper puts forward a bearing load identification method based on the measured three section strain values. Shaft is divided into several sections at strain gauge locations. The force and moment equilibrium equations are set up and assembled to form bearing load solving equations. This method can reduce the modeling error, especially for the machines with irregular rotating parts. It can also be applied for the entire shaft system bearing load distribution study with high accuracy and fault tolerant. Test was done on a rotor-bearing system rig. Bearing load distribution in different shaft alignment states is identified and analyzed. Test results show that the bearing load distribution varies sensitively and linearity to the change of bearing elevation. Further research shows that the accuracy of the method depends on the strain gauge locations. It would be best to place the strain gauge at location where the bending moment is sensitive to the change of bearing load. Moreover, mounting the strain gauge further from the bearing reduces the relative error due to the exact reaction point location is not known, which influences the accuracy of beading moment arm from the strain gauge location to the reaction point.     

电浮筒液位计的在线维修

介绍PET装置反应器上使用的电浮筒液位计的结构、原理,并对其典型故障进行在线维修的处理步骤进行了分析。