Synthesis,characterization, and thermal properties of phosphorus‐containing,wholly aromatic thermotropic copolyesters

A series of phosphorus‐containing, wholly aromatic thermotropic copolyesters from acetylated 2‐(6‐oxide‐6H‐dibenz〈c,e〉〈1,2〉oxa phosphorin‐6‐yl)‐1,4‐dihydroxy phenylene, p‐acetoxybenzoic acid, terephthalic acid, and isophthalic acid were prepared by melting polycondensation. The structure and basic properties of the polymers, such as the glass‐transition temperature (T_g), melting temperature (T_m), thermal stability, crystallinity, and liquid crystallinity, were investigated with Fourier transform infrared, elemental analysis, differential scanning calorimetry (DSC), thermogravimetric analysis, wide‐angle X‐ray diffraction, and hot‐stage polarizing optical microscopy. The copolyesters had relatively high T_g values ranging from 183 to 192°C. The T_m values obtained from DSC curves for samples P‐20 and P‐25 were 290 and 287°C, respectively (where the number in the sample name indicates the molar fraction of the phosphorus‐containing monomer in the reactants). The initial flow temperatures of other samples observed with hot‐stage polarizing microscopy were 271–290°C. The 5% degradation temperatures in nitrogen ranged from 431 to 462°C, and the char yields at 640°C were 41–52%. All the copolyesters, except P‐40, were thermotropic and nematic. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 1278–1284, 2002     

Structural development in cycloolefin copolymers under uniaxial elongational flow

Development of structures in new cycloolefin copolymers (COCs) of ethylene–norbornene (E–NB) and ethylene–tetracyclododecene (E–TD) of different NB/TD compositions were investigated under uniaxial elongational flow. For E–NB copolymer, which has multiblock sequences, a shoulder in WAXD at 0.76 nm was evident besides its amorphous halo, and the relative intensity of the peak increased with increasing comonomer content (NB). The appearance of a new peak for E–TD copolymer, and a relatively higher intense peak for E–NB copolymer at the same position of 0.76 nm, indicated that local ordering of the segments occurred when the COC was subjected to uniaxial flow. A lower comonomer composition of elongated COC, at a constant Hencky strain rate, exhibited two T_g values, whereas a higher composition showed a single T_g. Both local ordering and segmentization occurred in low comonomer content COCs but only local ordering occurred in higher comonomer content COCs. Both the shear viscosity and roll processing experiments exhibited similar phenomena of segregation. A model is proposed to illustrate the structure of COC after uniaxial elongation/deformation. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 91: 3421–3427, 2004     

发展玻璃纤维产业纺织品

本文层层深入地介绍产业用纺织品发展与应用、玻璃纤维纺织品发展与应用,以及它们的国内外概况并给出一些意见,以期待玻璃纤维产业纺织品有更好的发展.     

Low-E镀膜中空玻璃窗的能量平衡探讨

介绍了各种结构Low-E中空玻璃窗的传热性能,对窗户各个朝向的能量平衡进行了分析,说明通过Low-E中空玻璃窗户能更多地获得太阳能,同时可以减少建筑物能耗.建议根据建筑物的方向不同,在窗户的设计上也应有相应的差别.     

Isotactic polypropylene hollow microfibers prepared by CO2 laser‐thinning

An isotactic polypropylene hollow microfiber was continuously produced by using a carbon dioxide (CO₂) laser‐thinning method. To prepare the hollow microfiber continuously, the apparatus used for the thinning of the solid fiber was improved so that the laser can circularly irradiate to the hollow fiber. Original hollow fiber with an outside diameter (OD) of 450 μm and an internal diameter (ID) of 250 μm was spun by using a melt spinning machine with a specially designed spinneret to produce the hollow fiber. An as‐spun hollow fiber was laser‐heated under various conditions, and the OD and the ID decreased with increasing the winding speed. For example, when the hollow microfiber obtained by irradiating the CO₂ laser to the original hollow fiber supplied at 0.30 m min^?1 was wound up at 800 m min^?1, the obtained hollow microfiber had an OD of 6.3 μm and an ID of 2.2 μm. The draw ratio calculated from the supplying and the winding speeds was 2667‐fold. The hollow microfibers obtained under various conditions had the hollowness in the range of 20–30%. The wide‐angle X‐ray diffraction patterns of the hollow microfibers showed the existence of the highly oriented crystallites. Further, the OD and ID decreased, and the hollowness increased by drawing hollow microfiber obtained with the laser‐thinning. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 2600–2607, 2006     

离子交换增强玻璃表面化学稳定性的研究

系统研究了化学钢化及盐溶液后处理对Na2O-CaO-SiO2玻璃表面化学稳定性的影响。详细考察了用熔融KNO3化学钢化的玻璃以及用适当盐溶液后处理的化学钢化玻璃,在受水侵蚀后R2O的沥滤量和失重以及受碱侵蚀后SiO2的溶出量和失重。结果表明,用熔融KNO3对玻璃进行钢化处理后,玻璃的耐水性和耐碱性均有明显下降。而将化学钢化的玻璃利用适当盐溶液处理后,可以改善钢化玻璃的化学稳定性,因而可以进一步提高化学钢化玻璃的使用性能和拓展其使用范围。     

溶液中钙离子对玻璃颗粒电泳沉积的影响

研究了玻璃颗粒在乙醇溶液中对Ca^2 的选择吸附，反转了玻璃颗粒在乙醇中的荷电性质，使玻璃颗粒能够在乙醇中与羟基磷灰石发生共沉积。讨论了不同离子浓度下电泳沉积的沉积量与沉积电流的变化情况，并以此对Ca^2 在电泳沉积中的作用进行了分析。实验结果证实：悬浮液中Ca^2 或吸附到玻璃颗粒上，改变其荷电性质；或留在溶液中，作为电泳沉积过程中电流的主要承载者。离子浓度对电泳沉积的效果有重要的影响，离子浓度太低或太高都易使涂层出现缺陷。分析了不同沉积条件下电泳沉积所得涂层的各种缺陷及其成因。     

无机抗菌磷酸盐玻璃及其性能的研究

采用高温熔融法,在磷酸盐玻璃的配合料中引入抗菌剂硝酸银,一次熔化制得抗菌玻璃材料。通过对磷酸盐玻璃的抗菌性能和缓释性能分析,结果表明:制备抗菌磷酸盐玻璃,合适的银含量为1.5%~2.0%(质量),处理温度在1200~1350℃,即可获得良好的抗菌效果和缓释性。     

21世纪新玻璃的发展

新玻璃是指与传统玻璃相比具有不同性质、功能和用途,或采用与传统玻璃不同的成分、原料和制备工艺而得到的玻璃材料及制品.在以信息技术为主导、多门高新技术为支柱的新经济时代,新玻璃主要用于信息技术、生命科学、新能源与再生能源、新材料、海洋科学、环境保护方面.本文阐述了新玻璃的特征、品种、制备与发展.     

Effect of Enameling on the Strength and Dynamic Fatigue of Soda–Lime–Silica Float Glass

The effect of a glass enamel coating on the strength and fatigue behavior of float glass was investigated. Commercially available enamel that was comprised of Cu₂Cr₂O₄ pigment particles in a bismuth-zinc borosilicate glass matrix was applied to a soda–lime–silica float glass via screen printing, followed by fusion at elevated temperature. Strengths of the enameled specimens were evaluated in biaxial flexure using a ring-on-ring (ROR) test geometry, and the data were analyzed using a conventional two-parameter Weibull distribution. Enameling was found to significantly degrade the strength of the float glass. There was no statistical difference in the characteristic strengths of samples enameled on the air side (66 MPa) compared with samples enameled on the tin side (61 MPa) of the float glass. Fractographic analysis revealed that the failures in the enameled float glass samples initiated at pores and pigment aggregates in the enamel, whereas failures in float glass samples initiated solely from surface flaws. Dynamic fatigue tests were performed on enameled float glass and indented float glass samples to determine the effect of the enamel on the stress corrosion behavior of the enameled components. There was no statistically significant difference between the stress corrosion exponents for the float glass and enameled float glass specimens.