机械研磨 Ni_(50)B_(50)合金形成非晶的过程

本文研究了机械研磨 Ni_(50)B_(50)合金非晶的形成过程。唯象地提出用 J-M-A 方程描述此过程,并作了简单的讨论。     

混合结构楼房爆破拆除倒塌范围的确定

通过对混合结构楼房爆破倾倒过程特点的分析,提出了楼房在倾倒过程中的运动计算模型,并应用体积平衡原理,得到这类楼房爆破爆堆参数计算公式,用该公式计算的结果与实例中爆堆实测数据相比较,相对误差不超过11%.     

羰基铁类随机混合吸波材料等效电磁参数的计算

本文为计及多重散射偶极子间的相互作用，引入参量εｈ和μｈ，导得一组公式。它不仅能计算铁氧体类也能计算羰基铁类的随机混合吸波材料的等效电磁参数，均与实验结果吻合良好。     

宣汉——达县地区飞仙关组储层预测方法研究

在宣汉-达县地区,以往仅依据地震属性来预测飞仙关组储层分布,钻探结果与实际情况不符,为此本文提出量化分析预测结合主参数分析的新方法和新思路。在量化分析中首先对飞仙关组储层进行高分辨率反演,获得储能系数图;然后结合主振幅剖面和主频率剖面分析,对储层进行预测。在研究区,本方法的预测结果与实钻情况相吻合。     

Color characteristics of Cu-Zn-Al alloys

ＣＯＬＯＲＣＨＡＲＡＣＴＥＲＩＳＴＩＣＳＯＦＣｕ－Ｚｎ－ＡｌＡＬＬＯＹＳ￣①Ｌｉ，Ｂａｏｍｉａｎ；Ｚｈａｎｇ，Ｘｉｕｈｕａ（ＳｈｅｎｙａｎｇＩｎｓｔｉｔｕｔｅｏｆＧｏｌｄＴｅｃｈｎｏｌｏｇｙ，Ｓｈｅｎｙａｎｇ１１００１５）ＣＯＬＯＲＣＨＡＲＡＣＴＥＲ...     

Structural and electrical properties of brush plated ZnTe films

Zinc telluride thin films were deposited by the brush plating technique at a potential of −0.90 V (SCE) on conducting glass and titanium substrates at different temperatures in the range 30–90 °C. The films were polycrystalline in nature with peaks corresponding to the cubic phase. Direct band gap of 2.30 eV was observed. XPS studiers indicated the formation of ZnTe. Depth profiling studies indicated a uniform distribution of Zn and Te throughout the entire thickness. EDAX measurements were made on the films and it was found that there was a slight excess of Te. The carrier concentration was found to vary from 10¹⁴–10¹⁵ cm⁻³ with increase of substrate temperature. The mobility was found to vary from 5 to 60 cm² V⁻¹ s⁻¹.     

An investigation of carbon nanotube jet grinding

Since their observation in 1976 and 1991, carbon nanotubes (CNTs) have generated much interest due to their properties and potential applications. CNTs are tubular carbon molecules with remarkable mechanical, electrical, chemical and thermal properties, which make them useful in various applications. Industries producing CNTs via the fluidized bed chemical vapor deposition technique face challenges related to the size of CNT bundles. The two main challenges are agglomeration and agglomerate size distribution control. A solution to these challenges involves the use of jet mills to grind the CNT agglomerates. The goal of this study was to determine whether the nanotubes could be ground with air jets using a commercial jet mill and apply a two-parameter model to describe the grinding process. The present study has indicated that air-jet grinding of CNTs is feasible with a typical commercial jet mill. This paper presents the effect of operational parameters on the arithmetic mean diameter of the ground product. Sonic velocity through the grinding nozzles was required to obtain reasonable grinding rates and relatively narrow particle size distributions. This occurs at high air to solids feedrate ratios. Additionally, a simple attrition model can describe the grinding process in the spiral jet mill.     

Polyaniline-multiwalled carbon nanotube composites: Characterization by WAXS and TGA

Polyaniline/carboxylated multi-walled carbon nanotube (PAni/c-MWNT) nanocomposites have been synthesized by micellar aided emulsion polymerization with various c-MWNTs compositions, viz., 0.5, 1, 5, and 10 wt %. The microcrystalline parameters such as the nanocrystal size (〈N〉), lattice strain (g), interplanar distance (d_hkl), width of the crystallite size distribution, surface weighted crystal size (D_s), and volume of the ordered regions were calculated from the X-ray data by using two mathematical models, namely the Exponential distribution and Reinhold distribution methods. The effects of heat ageing on the microcrystalline parameters of the PAni/c-MWNT nanocomposites were also studied and the results are correlated. The thermal stability and electrical resistivity of the PAni/c-MWNT nanocomposites were examined with thermogravimetric analysis (TGA) and a conventional two-probe method. The TGA data indicate that the thermal stability of the nanocomposites improved after the incorporation of c-MWNTs. The influence of temperature on the resistivity of the nanocomposites was also measured. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

Novel approach in investigation of the poly(acrylic acid) hydrogel swelling kinetics in water

The swelling kinetics curves of structurally defined poly(acrylic acid) hydrogel in bidistilled water at temperatures: 25, 30, 35, 40, and 45°C were determined. The possibility of kinetically explaining the isothermal swelling process by applying the following models: reaction controlled by diffusion, first order chemical reaction kinetics, and second order chemical reaction kinetics, was investigated. It was found that kinetically explaining the swelling process using these methods was limited to only certain parts of the process. The swelling process in bidistilled water was described in full range assuming that the hydrogel's swelling rate was a kinetically controlled reaction by the rate of the movement of reactive interface of hydrogel. Based on that model, the kinetic parameters, activation energy (E_a) and preexponential factor (A), of the swelling process were determined to be E_a = 35 kJ/mol and lnA = 8.6. A possible mechanism of the investigated swelling process was discussed. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

GJ5×2双槽剥片机及其在高岭土剥片中的应用

GJ5×2大型双槽剥片机是国内超细物料加工中最新出现的超细磨/剥片设备,也是目前国内这一领域内最大规格的设备,已成功应用于煤系硬质高岭土剥片中,单机能力可达1.5～2.0t/h,产品细度可达小于2μm颗粒占85%～90%。